Table of Contents
Advertisement
Quick Links
BTFP02040 AIR COMPRESSOR
OPERATION AND MAINTENANCE MANUAL
BEFORE OPERATING THIS COMPRESSOR, THE USER SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE COMPRESSOR FOR FUTURE REFERENCE. IF YOU HAVE ANY
QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
BOSTITCH FASTENING SYSTEMS
N202452 07/12
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bostitch BTFP02040
Summary of Contents for Bostitch BTFP02040
- Page 1 BEFORE OPERATING THIS COMPRESSOR, THE USER SHOULD STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE COMPRESSOR FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR. BOSTITCH FASTENING SYSTEMS N202452 07/12...
-
Page 2: Table Of Contents
INTRODUCTION Congratulations on your purchase of a High Performance BOSTITCH Portable Air Compressor. This compressor has been designed to provide compressed air to power various pneumatic tools - including pneumatic fastening tools. Before assembling, operating or maintaining this air compressor, users must read and understand the information contained in this operation and maintenance manual. -
Page 3: Rules For Safe Operation
RULES FOR SAFE OPERATION (continued) Attachments and Accessories: For any attachment or accessory you will be using with this compressor, the maximum allowable recommended pressure should be clearly marked on the product or should be clearly noted within the operations manual. Exceeding the pressure rating of these attachments (including, but not limited to: air tools, air operated accessories, spray guns, air hose, air hose connections, tires and other inflatables) could cause them to fly apart or explode and could result in serious injury. -
Page 4: Electrical Grounding Instructions
AS FAR FROM SPRAYING AREA AS POSSIBLE. Risk of Burns: All air compressors generate heat, even operating under normal conditions. Bostitch compressors have been designed to reduce the risk of burns by limiting access to tubes and cylinder head parts. In areas where tubes are exposed, a protective sheathing has been added to the tubes to reduce risk;... -
Page 5: Specifications
NOTICE!: BOSTITCH does not recommend the use of extension cords with compressors. The use of an extension cord can result in the loss of voltage supplied to the compressor which could prevent the compressor from starting. -
Page 6: Features
FEATURES OF THE BOSTITCH BTFP02040 A. On/Off Switch B. Air Tank Pressure Gauge: The tank pressure gauge indicates the air pressure that is present in the tank in PSI (lbs/sq. in.) and BAR. C. Regulated Pressure Gauge: The regulated pressure gauge indicates the amount of pressure that is allowed into the discharge line/Quick connect (I) according to the setting of the regulator. - Page 7 OPERATION Pre-Start Procedures: 1. Inspect the compressor for any damaged components Do not operate if compressor is damaged. 2. Verify that the tanks have been drained and are clear of any moisture or dirt. (See “Draining Tank”). 3. INSTALLING THE DIPSTICK To prevent oil from spilling during shipping, the air compressor has a plug installed in the oil fill hole.
-
Page 8: Operation Instructions
OPERATION (CONTINUED) 1. CHECKING THE OIL The compressor is supplied with 354 ml of ISO100/SAE 40 Non-Detergent Oil for filling the pump crank case before operation. It is necessary to check the oil level before each use, and add oil if needed. NOTE: Always check the oil when the unit is sitting on a level surface. - Page 9 OPERATION (CONTINUED) 3. COLD WEATHER STARTING • Turn the switch to the OFF (O) position. • Turn the tank drain valves counterclockwise to open. NOTE: The air compressor has two tanks. Be sure to open both tank drain valves. • Turn the switch out to the ON ( l ) position and run the compressor for 1 - 2 minutes. •...
-
Page 10: Maintenance
Prior to performing service and maintenance to the compressor, always disconnect all accessories and attachments from the unit, and disconnect the compressor from the electrical source. When replacing parts, only use Genuine BOSTITCH replacement parts. 1. REPLACING THE AIR FILTER If you notice a reduction in performance of the air compressor, and the air delivery is lower than desired, it may be necessary to replace the air filter. -
Page 11: Trouble Shooting Guide
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION 1) Loss of power or overheating 1) Check for proper use of extension cord 2) No electrical power 2) Check to be sure unit is plugged in. Check fuse/breaker or motor overload 3) Blown shop/house fuse 3) Replace shop/house blown fuse Compressor will 4) Shop/house breaker open... -
Page 12: Warranty
Stanley Australia recommends that all torque wrenches be recalibrated at least once per year, depending on usage); (f) Bostitch branded pneumatic staplers or nailers are warranted for a period of seven (7) years from the date of purchase; and (g) Bostitch compressors and tools used in production applications are warranted for twelve (12) months from the date of purchase. - Page 13 (e) Universal sockets, universal joints, thin-wall impact sockets, adapters and retaining rings; (f) Facom products that are not distributed through Stanley Australia's authorised Distributors and resellers; and (g) Ultrasonic measuring tools. 1.6 (Products capable of repair) For certain Stanley Products that are found to be defective but repairable, it may only be necessary to replace a particular part.
- Page 14 NOTES:...
- Page 15 NOTES:...
- Page 16 (e) Universal sockets, universal joints, thin-wall impact sockets, adapters and retaining rings; (f) Facom products that are not distributed through Stanley Australia's authorised Distributors and resellers; and (g) Ultrasonic measuring tools. 1.6 (Products capable of repair) For certain Stanley Products that are found to be defective but repairable, it may only be necessary to replace a particular part.
Need help?
Do you have a question about the BTFP02040 and is the answer not in the manual?
Questions and answers