On installation of the appliance, the technical ced, copied or utilised in any other way wit- and administrative regulations of the country hout written authorisation by Dometic GmbH, in which the vehicle will first be used must be Siegen. adhered to. Otherwise the refrigerator must be installed as described in these instructions.
Safety instructions 2.0 Safety instructions Application according to WARNING! regulations Never open the absorber cooling unit! It is This refrigerator is designed for installation in under high pressure. recreation vehicles such as caravans or motorhomes. The appliance has been type- There is a danger of injury! approval tested for this application in accor- dance with the EC Gas Directive.
Description of model 3.0 Description of model Refrigerator rating plate Model identification Example : The rating plate is to be found on the inside of (S) (L) 8 4 0 0 the refrigerator. It contains all important details of the refrigerator. You can read off from this the model identification, the product number and the serial number.
If the door/grille distance is between 25 mm and ons, as follows: 45 mm, we recommend installing a Dometic The electrical installation must comply ventilation kit ( item no. 241 2985 - 00/0 ) to with national and local regulations.
Installation 4.1.2 Side installation with floor-roof ventilation With this installation method, regular main- Proper ventilation of the refrigerator can also be tenance of the gas burner is only possible achieved by lower air intake aperture in the floor once the device has been dismantled. It is and upper roof exhaust vent (see Fig.
Adequate sealing between the back of the refri- Fig. 12 gerator and the vehicle interior has to be provi- ded. Dometic strongly recommends carrying this out using a flexible seal (in order to simplify later removal and installation of the unit for mainten- ance purposes.
Installation The refrigerator is later pushed into the installa- tion recess from the front. Ensure that the seals abut the case evenly. This installation option facilitates the removal and installation of the appliance for servicing. Fig. 16 Flue duct Proposal 2 Deviations require the consent of the manu- Fasten the sealing lips to a stop bar on the rear facturer!
250cm². This is functional parts during maintenance. achieved by using the Dometic L100 / L 200 absorber ventilation and air extraction system which has been tested and approved for this purpose.
Installation To install the ventilation grilles, cut two rectan- Exhaust gas duct and instal- gles (451 mm x 156 mm) in the outer wall of the ling the fume flue vehicle ( for position of the cuts, see point 4.2 ). The exhaust gas duct system must be made in such a manner as to achieve a complete extrac- tion of combustion products to the outside of...
Installation 4.5.1 Installation in the recess Note: When installing the appliance ensure that the door hinges are supported. Figure 28 shows the optimum installation of the refrige- rator, whereas Fig. 29 shows the minimum requirement with the maximum clearance bet- ween installation area and end of hinge.
Installation Securing the refrigerator Inserting the decor panel In the sidewalls of the refrigerator, there are four Model RM 8xxx, RMS 8xxx plastic sleeves for securing the refrigerator. The sidewalls or strips attached for securing the Remove the lateral ledge (1) the door refrigerator must be prepared to hold the screws (ledge is attached, not screwed).
Page 18
Installation Model RML 8xxx Model RML 8xxx, frameless decor panel Fig. 38 Fig. 35 CAUTION! Fig. 39 Fig. 36 Fig. 37 Fig. 40 Decor panel dimensions : Casing width 525 mm Height Width Thickness 1169,5 +0/-1 mm 507,5 +0/-1 mm max. 1.7 mm Fig.
A plate showing the permanent, clearly legible notice must be displayed in full view at the point where Dometic refrigerators are equipped for a con- the gas cylinder is installed. nection pressure of 30 mbar. For connection to...
(otherwise Should the connection cable be damaged, the battery would discharge within a few hours), have it replaced by Dometic Customer perform the power supply to the heating ele- Services or by qualified personnel to avoid ment (cf.
Installation 4.9.3 Terminal block on the appliance Connections : A = Ground heating element DC B = Positive connection, heating element DC C = Ground electronics D+ S+ D = Positive connection, electronics D+ = Alternator signal on the vehicle S+ = AES input signal from solar charge regulator Fig.
Page 23
Installation Wiring diagram RM8xx1 : Fig. 47 For MES and AES it is compulsory to provide a permanent 12V DC supply at the terminals C/D (permanent voltage supply for functional electronics).
Page 24
Installation Wiring diagram RM8xx5 : Fig. 48 For MES and AES it is compulsory to provide a permanent 12V DC supply at the terminals C/D (permanent voltage supply for functional electronics).