Sony RDR-GXD455 Service Manual page 16

Controlling TVs with the remote
You can adjust the remote control's signal to
control your TV.
Notes
• Depending on the TV, some or all of the buttons below
may not work for the TV.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
1 1 2 2 3 3
Number
4 4 5 5 6 6
buttons
7 7 8 8 9 9
0 0
TV DIGITAL/
ANALOG
TV "/1
TV VOL +/–
TV INPUT
TV CH +/–
1
Hold down TV "/1 located at the bottom of
the remote.
Do not press "/1 at the top of the remote.
2
With TV "/1 pressed down, enter your
TV's manufacturer code (see below) using
the number buttons.
3
Release TV "/1.
The following buttons are for TV.
Press To
TV "/1
Turn your TV on or off
TV VOL +/– Adjust the volume of
your TV
TV CH +/– Select the channel on
your TV
B While holding down ENTER, enter the
command mode code number using the
number buttons.
Command Mode Code number
DVD1 number button 1
DVD2 number button 2
DVD3 number button 3
C Hold down both the number buttons and
ENTER at the same time for more than
three seconds.
To return to the previous display
Press O RETURN.
To check the command mode for the recorder
Press x (stop) on the recorder when the recorder
is turned off. The command mode for the recorder
appears in the front panel display.
If the command mode for the recorder has not
been changed, set the command mode for the
remote to the default setting of DVD3. If the
command mode for the remote is changed to
DVD1 or DVD2, you will be unable to operate
this recorder.
TV INPUT Switch your TV's input
source
TV DIGITAL / Select the broadcast on a
ANALOG Sony TV that can switch
between digital and
analog
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
Manufacturer Code number
Sony 01 (default)
Akai 04
AOC 04
Centurion 12
Coronado 03
Curtis-Mathes 12, 14
Daewoo 04, 22
Daytron 03, 12
Fisher 11
General Electric 04, 06, 10
Hitachi 02, 03, 04
J.C.Penney 04, 10, 12
JVC 09
KMC 03
LG/Gold Star 03, 04, 17
Magnavox 03, 04, 08, 12, 21
Marantz 04, 13
MGA/Mitsubishi 04, 12, 13, 17
NEC 04, 12
Panasonic 06, 19
Philco 02, 03, 04, 08
Philips 08, 21
Pioneer 06, 16
Portland 03
Proscan 10
Quasar 06, 18
Radio Shack 05, 10, 14
RCA 04, 10
27
,continued
Step 7: Easy Setup
Follow the steps below to make the minimum
number of basic adjustments for using the
recorder. If you do not complete Easy Setup, it
will appear each time you turn on your recorder.
Settings are made in the following order.
OSD Language Setup
m
Tuner and Channel Setup
m
Clock Setup
m
TV Type Setup
m
Audio Connection Setup
m
Finished!
"/1
1 1 2 2 3 3
4 4 5 5 6 6
7 7 8 8 9 9
0 0
M/m/</,,
ENTER
O RETURN
1
Turn on the TV.
2
Press "/1.
The recorder turns on.
,continued 29
Manufacturer Code number
Sampo 12
Samsung 03, 04, 12, 20
Sanyo 11, 14
Scott 12
Sears 07, 10, 11
Sharp 03, 05, 18
Sylvania 08, 12
Teknika 03, 08, 14
Toshiba 07, 18
Wards 03, 04, 12
Yorx 12
Zenith 14, 15
If you have a Sony DVD player or
more than one Sony DVD recorder
If the supplied remote interferes with your other
Sony DVD recorder or player, set the command
mode number for this recorder and the supplied
remote to one that differs from the other Sony
DVD recorder or player after you have completed
"Step 7: Easy Setup."
The default command mode setting for this
recorder and the supplied remote is DVD 3.
1 1 2 2 3 3
Number
4 4 5 5 6 6
buttons
7 7 8 8 9 9
0 0
SYSTEM
MENU
M/m/</,,
ENTER
O RETURN
28
3
Switch the input selector on your TV so that
the signal from the recorder appears on
your TV screen.
"Initial setting necessary to operate the DVD
recorder will be made. You can change them
later using setup." appears.
• If this message does not appear, select "Easy
Setup" in the "Setup" display to run Easy
Setup (page 88).
4
Press ENTER.
The setup display for selecting the language
used in the on-screen display appears.
Easy Setup
No Disc
Select the screen language.
English
Français
Español
5
Select a language, and press ENTER.
The display to confirm scanning appears.
Easy Setup
No Disc
Press [ENTER] to start scanning
Digital and Analog channels.
Start
6
Press ENTER.
The setup display for channel setting appears.
7
Select whether or not you have a cable
connection.
No Disc Easy Setup
Select the way in which you will receive
channels.
Antenna
Cable
If you use an antenna only (no cable TV),
select "Antenna."
For all other connections, select "Cable."
30
1-6
1
Check that Easy Setup (page 29) has been
finished. If Easy Setup has not been
finished, first perform Easy Setup.
2
Press SYSTEM MENU.
The System Menu appears.
3
Select "Setup," and press ENTER.
No Disc Setup 10:10 AM
Title List
Tuner Preset
Clock Set
Timer
Video
Edit
Audio
DV/D8 Dubbing
Features
Disc Setting Options
Easy Setup
Setup
4
Select "Options," and press ENTER.
Options 10:10 AM
No Disc
Title List
Language
Parental
Timer
Digital Wide Control : 16:9
Edit
: Off
Caption Service
DV/D8 Dubbing
Caption Setting
Disc Setting Front Display : Auto
Command Mode : DVD 3
Setup
Factory Setting
5
Select "Command Mode," and press
ENTER.
Options
No Disc 10:10 AM
Title List
Language
Parental
Timer
Digital Wide Control : 16:9
Edit
Caption Service : Off
DV/D8 Dubbing
Caption Setting
DVD 1
Disc Setting Front Display : Auto
DVD 2
Command Mode : DVD 3 DVD 3
Setup
Factory Setting
6
Select a command mode ("DVD 1," "DVD
2," or "DVD 3"), and press ENTER.
7
Set the command mode for the remote so it
matches the command mode for the
recorder you set above.
Follow the steps below to set the command
mode on the remote.
A Hold down ENTER.
8
Press ENTER.
The Tuner Preset function automatically starts
searching for all of receivable analog channels
and presets them.
Easy Setup
No Disc
Searching for receivable Analog channels.
Please wait.
Stop
After searching for analog channels is
complete, receivable digital channels are then
searched for automatically.
Easy Setup
No Disc
Searching for receivable Digital channels.
Please wait.
Allow 40+ minutes for completion.
To stop searching, press [Enter].
Stop
• This may take 40 minutes or more to
complete.
• If you press ENTER during search for
channels, the recorder will stop searching
for channels and advance the next step.
To set analog channels manually, see page 77.
After the Tuner Preset is finished, the setup
display for clock setting appears.
9
Select a method for setting the clock.
No Disc Easy Setup
Select a method for setting the clock.
If you select "Auto", this recorder will look
for a time signal when you turn it off.
Auto
Manual