Hardware Bag Contents And Tool List; Mounting The Reflectors - Burley d’Lite Owner's Instruction & Safety Manual

XIII. Parts List and Drawing
ote: Subassemblies are indented. Inquire for additional parts.
N
1 (1) Preassembled Main Frame Assembly
2 (1) Front Main Frame, 1" Aluminum Tube
3 (1) Rear Main Frame, 1" Aluminum Tube
4 (1) Left Inner Frame, 1" Aluminum Tube
5 (1) Right Inner Frame, 1" Aluminum Tube
6 (1) Bag Holder, 3/4" Aluminum Tube
7 (4) Wheel Dropout
8 (1) Roll Bar Assembly
9 (1) Roll Bar Receptacle, Plastic
10 (1) Roll Bar Hinge, Plastic
11 (1) Tongue and Hitch Assembly
12 (1) Tongue, 1 1/8" Aluminum Tube w/Bushing, Spindle &
Dropout
13 (1) Hitch w/Hitch Knob & Ball
14 (1) Hitch Safety Strap
15 (1) Clip & D-Ring
16 (1) Rubber Flex Connector
17 (1) Tongue Receptacle, Plastic
18 (2) Side Rail, 3/4" Aluminum Tube
19 (2) Holder for Child Seat Center Support Strap
20 (2) Pair Plastic Batten Connector (Front & Rear)
21 (2) Upper Aluminum Batten
22 (2) Lower Aluminum Batten
23 (2) Pair Side Rail Hinges, Per Side Rail
24 (10) Side Rail Snap Stud
25 (4) Reflector Bracket
26 (1) Fabric Bottom Bag and Side Panel Assembly w/Vinyl Win-
dows
& Side Pockets
27 (1) Fabric Child Seat with Harness
28 (1) Buckle for Lap Belt
29 (1) 2-Piece Safety Flag
30 (1) Bungee Cord
31 (1) Sunscreen Cover
32 (1) Hardware Bag containing:
33 (2) Front Reflector with Self-Tapping Screw
34 (2) Rear Reflector with Self-Tapping Screw
(2) Wheel Quick-Release Levers (not shown)
(2) Dished Wheels w/Quick-Release Seal-Mech Hubs (not
shown)
35 (1) Upper Buckle Strap
36 (1) Lower Buckle Strap
Options (at additional cost):
Flow-Thru 2-in-1 Cover (not shown)
Walk 'n Roller stroller kit (not shown)
22
I.

Hardware Bag Contents and Tool List

IMPORTANT: Please verify that you have received all of the contents
listed. Do not proceed with assembly if any parts are missing;
contact Burley immediately for replacement parts.
Hardware Bag Contents
Reflectors:
(2) Front reflector, clear
(2) Rear reflector, red
(4) Self-tapping screw, reflector
Envelope:
Trailer Checklist
Warranty Card
Burley d'Lite Owner's Instruction & Safety Manual
II.

Mounting the Reflectors

1. With the trailer side panels in folded position locate one of the
black molded hinges (A) at the rear trailer corner.
2. At the top of the hinge locate the screw hole (B) and reflector
locating boss (C). Each reflector has a
screw hole (D) and a location
stub (E).
3. Take a red reflector
D
and screw it to the
hinge as shown in
the figure below.
Line the reflector
hole (D) up with the
hinge screw hole (B)
and the reflector stub
(E) with the hinge
locating boss (C).
4. Repeat the procedure
with the second red
reflector, on the other rear trailer
hinge.
5. In similar fashion, repeat steps 1
through 4 on the trailer front using
the two clear reflectors.
Quick-Release Levers:
(2) Quick-release lever
Tools Required:
5/16", 8mm or small adjustable wrench
Small, straight blade screwdriver
A
B
E
C
3