Sharp SF-2030 Service Manual page 134

Display codes other than trouble
Trouble codes
CH
PC
PF
(Key operator program)
The list below shows all key operator programs. These programs can be used only when the key operator code in inputted at the beginning.
Program
Program name
Code No.
P10 Auditing Mode
P11 Number of Copies per Account
P13 Resetting Account
P14 Account Number Control
P16 Account Limit Setting
P18 Account Number Security
P19 Key Operator Code Number Change
P20 Auto Exposure Adjust
P21 Auto Power Shut-off Timer
P22 Toner Save Mode
P23 Auto Clear Setting
P24 Add or Change Extra Preset Ratios
P25 Setting a Maximum Number of Copies
P26 Initial Margin Shift Setting
P27 Erase Width Adjustment
P28 Initial Status Setting
P29 Total Copy Count
P31 Preheat Mode Setting
P42 Right/Left Shift Direction Selection
P45 Message Time Setting
P46 Power On Control
P47 Stream Feeding Mode
P51 Sorter Bin Access Mode
P70 Disabling of Auto Paper Selection
P71 Disabling of Auto Tray Switching
P72 Prohibiting of Manual Feed Tray in
Duplex Copy
P73 Disabling Deletion of Job Programs
P74 Disabling of Document Feeder
P75 Disabling of Duplex Copying
P76 Disabling of Stapler
P77 Disabling of Covers
P83 Disabling of PC/Modem Access
P90 Display the List of All P Codes
Sub code
— Door open/DV unit uninstalled
— Personal counter uninstalled/auditor code input waiting
— Copy inhibit command is received from the host when installing PC/Modem.
Enables or disables the basic auditing mode, which controls access to copier.
Displays the total number of copies made against account numbers.
Resets all audit accounts or selectively resets individual accounts.
Registers accounts, deletes accounts, changes an account number, or displays all
registered account numbers.
Sets the maximum number of copies which can be made against a registered account
number.
Guards against trial and error entering of audit account numbers.
Changes the key operator code number.
Lightens or darkens copies in the automatic exposure mode.
Sets a time interval after which the copier automatically turns off.
Reduces toner consumption.
Sets a time interval after which the copier returns to the initial settings.
Adds or changes reduction and enlargement preset copy ratios.
Sets the maximum number of copies that can be selected.
Sets the initial margin shift values.
Sets the amount of the erase area.
Sets the copier's initial settings in the ready condition.
Recalls the total copy counts of the copier, document feeder, duplex module, and stapler.
Sets the time that elapses before the copier enters the preheat mode after copying is
completed.
Determines whether shift direction change is to be allowed.
Sets the length of time that messages are displayed.
Prevents the copier from being started by people other than key operator.
Enables the stream feeding mode for copying from an optional document feeder.
Enables or disables the sorter bin access mode when an optional 10-bin sorter (SF-S18)
is installed.
Prevents automatic paper selection when using the ORIGINAL SIZE ENTER key or
copying from an optional document feeder.
Prevents automatic switching between the paper trays.
Prohibits the use of the manual feed tray during duplex copying. (Duplex copying can be
performed when an optional duplex module is installed.)
Prevents stored programs from being replaced or deleted.
Prevents the use of an optional document feeder when it malfunctions.
Temporarily prevents the optional duplex system from operating when it malfunctions.
Allows the use of the copier but not the duplex system.
Prevents damage to the stapler while awaiting repair service. (Staple sorters are
optional.)
Prevents the selection of COVERS mode.
(The COVERS mode can be used when an optional document feeder is installed.)
Provides or prevents access to key operator programs through a PC/modem without key
operator code entry.
(Remote access to key operator programs can be performed only when a computer or
other equipment is connected to the copier directly or through a telephone line.)
Sequentially displays all available programs.
Operation
Function
8 – 19