Grundig UMS 25 Service Manual page 10

SETTINGS
____________________________________________________________________________
Setting the time
When the stereo is connected to the mains supply and the time has not been set,
the time display flashes.
Note:
Perform the setting in switched-off state.
1 1:20
1
Activate time-setting function by pressing »
down.
– In the display, »
2 Press » MEMORY« and set the hour with »
3 Press » MEMORY« and set the minute with »
15:00
4
Confirm input with » MEMORY«.
Note:
The time must be reset after a power failure or when the mains plug is pulled
out.
Setting the time for 12-hour display
1
14:00 Switch on stereo system by pressing »
2 Press »SOURCE« until »
| __ | __ | __ | __ | __ | __ | __ | __
I
I I I 3 Activate the time-setting function by pressing »
VOLUME I I I I
| __ | __ | __ | __ | __ | __ | __ | __
– In the display, for example, » I 4 : 0 0 « appears.
PM 02.00
4 Press » MEMORY« and hold down while pressing »
– » P M « appears briefly in the display; the time has been switched to
12-hour display.
| __ | __ | __ | __ | __ | __ | __ | __
I I I
I I I
| __ | __ | __ | __ | __ | __ | __ | __ VOLUME I I
Note:
Repeat procedure to set for 24-hour display.
CLOCK TIMER « and holding
« flashes.
– VOLUME + «.
– VOLUME +«.
ON «.
TAPE
« appears in the display.
CLOCK TIMER «.
«.
II
SETTINGS
____________________________________________________________________________________
Searching for and saving radio stations –
with the automatic station search
TUNER
Note:
MHz
When making this setting, no more than 5 seconds may elapse between
pressing various keys.
| __ | __ | __ | __ | __ | __ | __ | __
I I I
I I I
| __ | __ | __ | __ | __ | __ | __ | __ VOLUME I I
1 Switch on stereo system with
FM 87.50
MHz 2 Select desired frequency range (FM, MW or LW) with
– In the display, » F M 8 7 . 5 0 « may, for example appear.
| __ | __ | __ | __ | __ | __ | __ | __
I I I 3 Start the automatic station search for the FM range by keeping
I I I I
| __ | __ | __ | __ | __ | __ | __ | __ VOLUME I
»a a TUNE –
« or
– The search stops, as soon as a radio station with a sufficiently strong signal
is found.
– The frequency of the station can be tuned step-by-step (500kHz) with
»a a TUNE –
« or
FM PR:02
MHz
PROG.
4 Press »MEMORY« and select the desired station with »PRESET« or
ST
»1 ... 0« on the remote control (1 to 24 in the FM range, 1 to 12 in
| __ | __ | __ | __ | __ | __ | __ | __ the MW and LW ranges).
I I
I I I
VOLUME I I I
| __ | __ | __ | __ | __ | __ | __ | __
– The selected channel position appears in the display, » F M P R : 0 2 «, for
example, and in the case of RDS stations, the station name appears direct-
ly afterwards.
5 Save setting with »MEMORY«.
– In the display, the selected channel position will appear, for example
» F M P R : 0 2 «.
6 To tune into other radio stations in the FM range, repeat procedure from
point 3, for the ranges » M W « and » L W «, repeat from point 2.
»TUNER /BAND«.
»TUNER
/BAND«.
s« on the remote control pressed down.
»TUNE +s
s« on the remote control.
»TUNE +s