Samsung RS261M Repair Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Refrigerator
  5. RS261M Series
  6. Repair manual

Samsung RS261M Repair Manual

Hide thumbs Also See for RS261M:
Table of Contents

Advertisement

Quick Links

See also: User Manual
HA Repair Guide
Refrigerator
SSEDA – RS261*
- 1/47 -

Advertisement

Table of Contents
loading

Related Manuals for Samsung RS261M

Summary of Contents for Samsung RS261M

  • Page 1 HA Repair Guide Refrigerator SSEDA – RS261* - 1/47 -...
  • Page 2 SSEDA-PJT Repair Guide [ RS261M* ] • No Ice / dispensing problem No Ice • Shortage of ice • No Water / Water Dripping No Water • Water Leak Defrost • Evap Defrost build • Water hose Noise Noise • Unit Noise •...
  • Page 3 ● Ice & Water #1. Symptom : No Ice Repair Schematic Chassis Project Basic Model Type SSEDA RS261M* Plastic Ice Maker ※  Check Display “ICE off” selecting Block Reason Step Check-1 Check-2 Code  Inspect Display Water Display selection...
  • Page 4 Tip 1-1. Inspect Display Water & Ice selection Inspect “Ice Type” button select operation Check Point Step 1 ① Check “Child Lock” selection ② Inspect “Ice Type” Key operation - Key normal  Inspect Tip 1-2 - Key failure  Inspect Step 2 Step 2 ①...
  • Page 5 Tip 1-2. Inspect Lever S/W & Auger Motor S/W operation Check Point Inspect Dispenser Lever S/W operation. Step 1 ① Check the Auger motor rotation sound which is inside of F room with pushing DISPENSER LEVER. - When operation sound does not appear, check Step 2 - When operation sound appears, check “STEP 4”...
  • Page 6 Tip 1-3. Inspect ASSY Auger Motor operation Check Point Inspect Auger Motor. Step 1 ① Disassemble ice Bucket which is in F room. ② Disassemble 3 screws on the top. Step 2 (Single product inspection) ① Disassemble ice bucket which is in freezer. ②...
  • Page 7 Tip 2-1. Inspect Water supply / supply Check Point Inspect Water supply failure ※ Need lever operation for 3 min on initial and after replace Filter ! Step 1 ① Inspect water comes when lever operation after Water selection. ※ Initial product needs Water Tank filling time - When the water does not come...
  • Page 8 Tip 2-2. Inspect Ice Valve operation Check Point Inspect ice maker Water supplying problem Step 1 ① 점ㄱ ① Push the button for 2 sec which is on the bottom of ice maker after disassemble Ice Bucket. ② Check the water supplying after ice maker tray twist operation.
  • Page 9 Tip 2-3. Inspect ASSY PIPE-WATER (Heater) freezing Check Point Inspect ice maker Water supply problem Step 1 Connector ① Disassemble the Ice Maker which is on top of F room. ② Disassemble top PIPE-WATER Heater Wire. - Normal product 1.8 ~ 2.5 KΩ - Failure part : Open or 0 Ω...
  • Page 10 (※ Must select “Power Freeze” first) Tip 2-4. Inspect Self diagnosis test ※ Fan motor Fan motor displays failure for power on condition. Touch Display “Lighting”+ “Energy Saver” Key for 8 sec at the same time. - Press until all LED blink and “dingdong” sound appears.
  • Page 11 Tip 2-4-1. Inspect self-diagnosis test  Inspect Ice Maker Block Connector ① Disassemble F Ice Maker Screw Top ② Inspect Wire Harness connection which is on Sensor The top part. ※ Ice maker test operates and water does not come, Check TIP 2-2 Test ※...
  • Page 12 Tip 2-4-2. Inspect self-diagnosis test  F Sensor / Cabinet Fan / Defrost Sensor / Defrost Error Block D-Sensor F-Sensor Fan Motor ① Disassemble F Ice Maker Screw top Heater ② Inspect Cover Multi Front disassemble Defrost ③ Inspect Evap Cover disassemble Sensor Circuit diagram ①...
  • Page 13 Tip 2-4-3. Inspect self-diagnosis test  R Sensor / F Damper Motor Block R-Sensor Damper Damper ① Disassemble R Ice Maker Screw top ② Inspect Cover Multi Front disassembly ③ Inspect Evap Cover disassembly R-Sensor Circuit diagram ① When the R cabinet Sensor is failure : Inspect disassembled Cover Damper blue 2-Wire...
  • Page 14 Tip 2-4-4. Inspect self-diagnosis test  External R Sensor / C-Fan Motor Block C-Fan EXT-Sensor - Inspect external air sensor ① Inspect R top HINGE-UPP Cover disassembled Wire Inspect - Inspect C-Fan Error Connector ① Inspect disassembled Unit Cover Fan restriction / Wire Circuit diagram ①...
  • Page 15 (※ Must select “Power Tip 2-5. Inspect cooling power Freeze” first) ※ Do not off the power  Measure self-diagnosis test on “TIP 2-4” Step 1 Press Display “Lighting”+ “Energy Saver” Key for 8sec at the same time. - Press until all LEDs are Blinking and “dingdong” sound appears ※...
  • Page 16 Step 4 (Comp single product operation failure) ① Inspect rotation failure by Comp Coil cutting - Measure Common + Sub resistance - Measure Common + Main resistance Normal : 1~50 Ω ∞ Failure : Open Ω Step 5 (Comp Relay Failure) ①...
  • Page 17 ● Ice & Water #2. Symptom : No Water & other(LEAK) Repair distribution diagram Chassis Project Basic Model Type SSEDA RS261M* Plastic Ice Maker ※ Check Display “Hold” selection Block Reason Step Check-1 Check-2 Code WATER supply  Inspect WATER...
  • Page 18 Tip 3-1. Inspect WATER connection / supply Check Point Inspect Water supply failure ※ Need lever operation for 3 min on initial and after filter replacement ! Step 1 ① Inspect lever water coming after Water selecting. ※ Takes water tank filling time of initial product - When the water does not come ...
  • Page 19 Tip 3-2. Inspect WATER VALVE operation Check Point Inspect WATER VALVE failure Step 1 ① Disassemble backside UNIT COVER. Step 2 ① After disassemble ASSY Valve and check WHITE 2-Wire - Normal parts : 350~450 Ω - Failure parts : Open or 0 Ω ②...
  • Page 20 Tip 3-3. Inspect WATER Lever S/W operation Check Point Inspect Dispenser Lever S/W operation. Step 1 ① After select DISPENSER WATER and check water coming with pressing LEVER Step 2 MAGNET CHECK ① Inspect F DOOR UPP MAGNET existence ② Inspect disassembled HINGE-UPP COVER DOOR S/W &WIRE CONNECTOR OPEN ※...
  • Page 21 Tip 3-4. Inspect WATER HOSE Check Point Inspect WATER HOSE LINE Step 1 ① Disassemble COVER-LEG FRONT. Step 2 ① Check it is the problem of WATER HOSE TUBE FITTING connection and disassemble it if there is no problem. ② On DOOR ALL CLOSE condition, check the water comes of hose when WATER LEVER operate.
  • Page 22 Tip 4-1. Inspect WATER LINE LEAK Check Point Inspect WATER HOSE LINE LEAK Step 1 ① Disassemble COVER-LEG FRONT. - FRONT WATER LEAK - ROOM WATER LEAK - BACK WATER LEAK Step 2 ① Inspect WATER HOSE SCRATCH  Re-connection after cutting the SCRATCH part ②...
  • Page 23 Tip 4-2. Inspect WATER DISPENSER DRIPPING Check Point Inspect WATER HOSE LINE LEAK Step 1 ① Disassemble COVER-LEG FRONT ※ WATER DRIPPING occurs as WATER LINE AIR Step 2 HOSE SCRATCH ① Inspect WATER HOSE SCRATCH  Re-connect after cutting SCRATCH part Step 3 ①...
  • Page 24 Tip 4-3. Inspect WATER HOSE NOISE Check Point Inspect WATER HOSE LINE LEAK HOSE Step 1 VIBRATION ① Dispense water with pressing WATER LEVER. - Inspect supply water pressure problem - Inspect CASE-FILTER problem Step 2 ① Check backside hose quake sound when operate with pressing WATER LEVER.
  • Page 25 ● DEFROST #1. Symptom : EVAP / ICE ROUTE DEFROST Repair Chassis Project Basic Model Type SSEDA RS261M* Plastic Ice Maker ※ Operate self-diagnosis test Block Reason Step Check-1 Check-2 Code DEFROST ERROR /  Self diagnosis test Sensor WIRE H...
  • Page 26 (※ Must select “Power Freeze” first) Tip 5-1. Self diagnosis test inspection ※ Fan motor displays failure for power on condition. Press Display “Lighting”+ “Energy Saver” Key for 8sec at the same time. - Press until all LEDs are Blinking and “Dingdong” sound occur - Normal on self-diagnosis test...
  • Page 27 Tip 5-1-1. Inspect self-diagnosis test  Inspect Ice Maker Block Connector ① Disassemble F Ice Maker Screw top ② Inspect wire harness contact on the top. Sensor ※ Ice maker test operation but water doesn’t come refer to TIP 2-2 ※...
  • Page 28 Tip 5-1-2. Inspect self-diagnosis test  F Sensor / cabinet Fan / Defrost Sensor / Defrost Error Block D-Sensor F-Sensor Fan Motor ① Disassemble F Ice Maker Screw top Heater ② Inspect disassembled Cover Multi Front 분해 Defrost ③ Inspect disassembled Evap Cover Sensor Circuit diagram ①...
  • Page 29 Tip 5-1-3. Inspect self-diagnosis test  R Sensor / F Damper Motor Block R-Sensor Damper Damper ① Disassemble F Ice Maker Screw top ② Inspect disassembled Cover Multi Front ③ Inspect disassembled Evap Cover R-Sensor Circuit diagram ① When the R cabinet Sensor is failure : Inspect disassembled Cover Damper blue 2-Wire...
  • Page 30 Tip 5-1-4. Inspect self-diagnosis test  External air R Sensor / C-Fan Motor Block C-Fan EXT-Sensor - Inspect external sensor ① Inspect disassembled R top HINGE-UPP Cover Wire Inspect - Inspect C-Fan Error Connector ① Inspect disassembled Unit Cover Fan restriction / Wire Circuit diagram ①...
  • Page 31 Tip 5-2. Inspect EVAP DEFROST BUILD ※ Do not off the power and operate self-diagnosis test on “TIP 5-1” first.  Must check the forced defrost operation after defrosting repair. Step 1 Press Display “Lighting”+ “Energy Saver” Key for 8 sec at the same time until “Dingdong”...
  • Page 32 Step 6 ① When it freezes only EVAP BOTTOM - Improve DRAIN freezing. ② Check the drain hole blocking with removing freezing with STEAMER. (Remove DRAIN freezing and foreign substance) ③ Bend the HATER to bottom with hand. - DRAIN HOLE should be closed. ★...
  • Page 33 Tip 6-1. Inspect ICE ROUTE DEFROST BUILD Step 1 ① Check frost attachment with ICE ROUTE on F- DOOR OPEN condition. - If the frost appears on ICE ROUTE only, it appears because of ICE dispensing so that is normal. Step 2 ( When freezing appears until ICE BUCKET bottom)
  • Page 34 ● NOISE #1. Symptom : Water Hose & UNIT NOISE Repair distribution diagram Chassis Project Basic Model Type SSEDA RS261M* Plastic Ice Maker ※ Operate self-diagnosis test Block Reason Step Check-1 Check-2 Code WATER HOSE  Inspect FILTER CASE Case-...
  • Page 35 Tip 7-1. Inspect WATER HOSE NOISE Check Point Inspect Noise when WATER dispensing HOSE Step 1 VIBRATION ① Dispense water with pressing WATER LEVER. - Inspect supplied water pressure problem - Inspect CASE-FILTER problem Step 2 ① Check backside hose quake sound with pressing WATER LEVER.
  • Page 36 Tip 8-1. Inspect UNIT NOISE Check Point Inspect UNIT NOISE Step 1 ① Disassemble backside UNIT COVER. Step 2 ① Inspect selecting “Power Freeze” and COMP ② Disassemble the part which is friction. PIPE + WIRE PIPE + TRAY PIPE + PIPE PIPE + TRAY FAN + WIRE PIPE + COVER...
  • Page 37 Tip 8-2. Inspect CYCLE NOISE Check Point Inspect NOISE Step 1 ① Disassemble backside UNIT COVER. Step 2 ① When “Pooo~” “growling” sound occurs in the cabinet ② Disassemble EVAP COVER. - Capillary Pipe welding part should be as “-” shape.
  • Page 38 ● COOLING #1. Symptom : WEAK COOLING & TOO COLD Repair Chassis Project Basic Model Type SSEDA RS261M* Plastic Ice Maker ※ Operate self-diagnosis test Block Reason Step Check-1 Check-2 Code Inspect F WEAK  Self diagnosis test Wire Main COOLING Display “Lighting”+...
  • Page 39 (※ Must select “Power Freeze” first) Tip 9-1. Inspect self-diagnosis test ※ Fan motor displays failure only for power On condition. Press Display “Lighting”+ “Energy Saver” Key for 8sec at the same time. - Press until “Dingdong” sound appear after all LEDs is blinking - No problem on self-diagnosis test...
  • Page 40 Tip 9-1-1. Inspect self-diagnosis test  Inspect Ice Maker Block Connector ① Disassemble F Ice Maker Screw top ② Inspect Top Wire Harness contact. Sensor ※ Water doesn’t come even ice maker operates Test, TIP 2-2 ※ If there is no problem on water supply problem Test and Test, TIP 2-5 button...
  • Page 41 Tip 9-1-2. Inspect self-diagnosis test  F Sensor / cabinet Fan / Defrost Sensor / Defrost Error Block D-Sensor F-Sensor Fan Motor ① Disassemble F Ice Maker Screw top Heater ② Inspect disassembled Cover Multi Front Defrost ③ Inspect disassembled Evap Cover Sensor Circuit diagram ①...
  • Page 42 Tip 9-1-3. Inspect self-diagnosis test  R Sensor / R Damper Motor Block R-Sensor Damper Damper ① Disassemble F Ice Maker Screw top ② Inspect disassembled Cover Multi Front ③ Inspect disassembled Evap Cover R-Sensor Circuit diagram ① When R cabinet Sensor is failure : Inspect disassembled Cover Damper blue 2-Wire...
  • Page 43 Tip 9-1-4. Inspect self-diagnosis test  External R Sensor / C-Fan Motor Block C-Fan EXT-Sensor - Inspect external sensor ① Inspect disassembled R top HINGE-UPP Cover Wire Inspect - Inspect C-Fan Error Connector ① Unit Cover disassembled Fan restriction / Wire inspection Circuit diagram ①...
  • Page 44 (※ Must select “Power Tip 9-2. Inspect cooling power Freeze” first) ※ Do not off the power  Measure self diagnosis test inspection on “TIP 9-1” Step 1 Press Display “Lighting”+ “Energy Saver” Key for 8 sec at the same time. - Press until all LEDs are Blinking and “DingDong”...
  • Page 45 Step 4 (Comp single product operation failure) ① Inspect rotating failure by Comp Coil cutting - Measure Common + Sub resistance - Measure Common + Main resistance Normal : 1~50 Ω ∞ Failure : Open Ω Step 5 (Comp Relay failure) ①...
  • Page 46 Tip 9-3. Inspect EVAP DEFROST BUILD ※ Do not off the power and operate self-diagnosis test to“TIP 5-1” first.  Must check the forced defrost operation after defrost repairing. Step 1 Press Display “Lighting”+ “Energy Saver” Key for 8sec at the same time until “Dingdong” sound appears ※...
  • Page 47 Step 6 ① When EVAP BOTTOM is freezing only - improve DRAIN freezing. ② Check Drain hole blocking with remove freezing with STEAMER. (Remove DRAIN freezing and foreign substance) ③ Bending the HATER to bottom with hand. - DRAIN HOLE Should be closed. ★...
  • Page 48 Tip 10-1. Inspect R TOO COLD Check Point Inspect COVER DAMPER Step 1 ① Disassemble the R ASSY COVER DAMPER. R-Sensor Damper Damper Step 2 ① Inspect the location fixing condition of R- SENSOR - TOO COLD occurs when separate or cover the front with protection vinyl.

Table of Contents