1. Manuals
  2. Brands
  3. Digital Equipment Manuals
  4. Printer
  5. DEClaser 2100 plus
  6. Operator's manual

Digital Equipment DEClaser 2100 plus Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DEClaser 2100 plus Printer
Operator's Guide
Order Number EK–DECLA–OG–001
Digital Equipment Corporation
Maynard, Massachusetts

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DEClaser 2100 plus and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Digital Equipment DEClaser 2100 plus

Summary of Contents for Digital Equipment DEClaser 2100 plus

  • Page 1 DEClaser 2100 plus Printer Operator’s Guide Order Number EK–DECLA–OG–001 Digital Equipment Corporation Maynard, Massachusetts...
  • Page 2 Any software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license. No responsibility is assumed for the use or reliability of software or equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.
  • Page 3 FCC NOTICE: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.

  • Page 4: Table Of Contents

    Contents Preface Chapter 1 Printer Components Functions of the Printer Components ....1–1 Required Operating Space ......1–8 Chapter 2 Operating Information Powering the Printer On .
  • Page 5 2.16.1 Entering Control Representation Mode ....2–51 2.17 Resetting the Printer ....... 2–52 2.18 Emulation Mode of Operation .
  • Page 6 4.5.6 INTERFACE Menu ......4–26 4.5.6.1 Interface Selection (i/f) ......4–28 4.5.6.2 Baud Rate (baud) .
  • Page 7 Replacing the Ozone Filter ......7–36 Chapter 8 Service Digital Equipment Corporation Services ....8–1 Appendix A DEClaser Printer Quick Reference Guide Positioning Controls .
  • Page 8 Appendix D LN03 Compatibility General Differences ....... . D–1 Printable Area Compatibility ......D–2 Protocol Compatibility .
  • Page 9 C–3 Serial Connections Without Modem ....C–6 C–4 Parallel Pin Assignment ......C–9 C–5 Parallel Connections .
  • Page 10 Character Set Identification ......A–17 B–1 DEClaser 2100 plus Printer Accessories and Supplies ..B–1 B–2...

  • Page 11: Preface

    User-installable PostScript upgrade capability Software Requirements Some features of the DEClaser 2100 plus printer may or may not be available depending on the operating software used by the host computer system and the application software that you are using. For information about the printer features you can use with your application program, consult your application program documentation.

  • Page 12: Document Structure

    This chapter also describes how to save values in memory. • Chapter 5, Print Media, describes the various printing media that can be used with the DEClaser 2100 plus, including paper, envelopes, transparencies, and labels. It also addresses the proper way to store and handle paper. •...

  • Page 13: Associated Documents

    • Appendix B, Accessories and Supplies, describes the accessories and supplies available for the DEClaser 2100 plus printer and explains how to order them. • Appendix C, Specifications, lists the power, environmental, and physical specifications of the DEClaser 2100 plus printer.
  • Page 14 This manual is for programmers who need to convert ReGIS or Tektronix 4010/4014 documents to PostScript for printing on PostScript printers. The DEClaser 2100 plus has a PostScript option and can print Tektronix 4010/4014 and ReGIS files using the Common Print Symbiont (CPS).

  • Page 15: Conventions Used In This Guide

    Conventions Used in This Guide The following terms and conventions are used in this guide: Convention Meaning NOTE Notes provide important additional information. CAUTION Cautions provide information required to prevent damage to equipment. WARNING Warnings provide information to prevent personal injury. Dash (—) A statement preceded by a dash describes the result of a procedural step.

  • Page 16: Safety Information

    — The menu display reads FONT/FEED LAYOUT. Safety Information The DEClaser 2100 plus printer complies with all United States government safety regulations applicable to ozone gas emissions and laser beam light exposure. Read the following information to become familiar with ozone and laser safety.

  • Page 17: Cdrh Label

    Laser Safety The DEClaser 2100 plus printer complies with 21 CFR Chapter 1, Subchapter J, as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968.

  • Page 18: Chapter 1 Printer Components

    Chapter 1 Printer Components This chapter describes the components of the DEClaser 2100 plus printer and their functions. This chapter also provides information about the operating space required to perform day-to-day printing operations. 1.1 Functions of the Printer Components Figures 1–1 through 1–3 show the printer components. Tables 1–1 through 1–3 explain the printer components and their functions.

  • Page 19: Components: Front/Right-Side View

    Figure 1–1: Components: Front/Right-Side View MLO-004826 1–2 Operator’s Guide...

  • Page 20: Printer Components: Front/Right-Side View

    Table 1–1: Printer Components: Front/Right-Side View Component Function 1. Top Output Tray Printed sheets are automatically collated and stacked (facedown) here. 2. Top Cover Release Button Pressing this button unlocks the top cover so it can be opened. The top cover is opened to perform certain printer funtions such as adding a new EP-S cartridge or clearing a paper jam.

  • Page 21: Components: Rear/Left-Side View

    Figure 1–2: Components: Rear/Left-Side View MLO-004827 1–4 Operator’s Guide...

  • Page 22: Printer Components: Rear/Left-Side View

    This connector is used when the interface cable from Interface Cable Connector the host computer is a parallel cable. Refer to the DEClaser 2100 plus Printer Installation Guide for more information about connecting the printer to your computer. 5. Serial (RS232C)

  • Page 23: Components: Inside The Printer

    Figure 1–3: Components: Inside the Printer MLO-004828 1–6 Operator’s Guide...

  • Page 24: Printer Components: Internal View

    Table 1–3: Printer Components: Internal View Component Function 1. Print Density Dial Has a range of 1–9 to adjust the print density. Selecting the lower numbers results in heavier or darker print density. For most printing applications the dial can be set to 7. See Section 2.11 for additional information about setting the print density.

  • Page 25: Required Operating Space

    Always allow ample space around the printer to perform day-to-day printing operations. Figure 1–4 and Figure 1–5 show the minimum amount of space required to perform these operations. See the DEClaser 2100 plus Printer Installation Guide for additional information about location requirements and environmental conditions.

  • Page 26: Operating Space: Top View

    Figure 1–4: Operating Space: Top View MLO-004346 Figure 1–5: Operating Space: Side View MLO-004844 Printer Components 1–9...

  • Page 27: Chapter 2 Operating Information

    Chapter 2 Operating Information This chapter provides the operating information necessary to perform day- to-day printer operations. It covers typical tasks such as adding paper, selecting an output tray, or powering the printer on and off. This chapter also covers manual feed operation for all print media. 2.1 Powering the Printer On Power the printer on using the following procedure.
  • Page 28 For instance, if you are using PostScript protocol, the display reads PS READY/IDLE. Since several protocols can be used with the DEClaser 2100 plus printer, the remainder of this manual shows the ready message as 00 READY. If the printer does not power on correctly, refer to Chapter 6 for troubleshooting information.

  • Page 29: Powering The Printer Off

    2.2 Powering the Printer Off Power the printer off using the following procedure. 1. Be sure the printer is not printing and that the Data indicator is not CAUTION: Do not power the printer off while it is printing. Powering the printer off during printing causes paper jams and loss of data.

  • Page 30: Opening The Top Cover

    2.3 Opening the Top Cover Open the top cover using the following procedure. 1. Press the release button forward and then down. — The top cover releases and opens slightly. Fig 2-3, MLO-004830 2–4 Operator’s Guide...
  • Page 31 2. Lift the top cover open to the halfway position (about 30°) or to the upright position (about 90°). Fig 2-4, MLO-004831 The halfway position is intended for: • Replacing the EP-S cartridge • Adjusting the print density dial The upright position is intended for: •...

  • Page 32: Closing The Top Cover

    2.4 Closing the Top Cover Close the top cover using the following procedure. 1. Gently lower the cover and push down on the hand grip until the cover latches securely in place. Fig 2-5, MLO-004366 2–6 Operator’s Guide...

  • Page 33: Selecting The Output Tray

    2.5 Selecting the Output Tray To select the paper output tray, you position the rear output tray to the open or closed position. NOTE: You cannot select the output paper tray through a command from the host computer; opening or closing the rear output tray is the only way to select the output tray.

  • Page 34: Selecting The Top Output Tray (Facedown Print)

    2.5.1 Selecting the Top Output Tray (Facedown Print) If the rear output tray is not open, the printer sends printed paper facedown to the top paper tray. If the rear output tray is open, use the following procedure to select the top output tray. 1.

  • Page 35: Selecting The Rear Output Tray (Faceup Print)

    2.5.2 Selecting the Rear Output Tray (Faceup Print) Use the following procedure to select the rear output tray. 1. Open the rear output tray. Fig 2-9, MLO-004835 2. Fold out the extension tray. Fig 2-10 MLO-004836 Operating Information 2–9...

  • Page 36: Loading Paper

    2.6 Loading Paper The printer comes standard with either an A4-size (210 mm x 297 mm) or letter-size (8 ½ in. x 11 in.) paper cassette, depending on the country it is shipped to. Optional paper cassettes are available that can accommodate the following print media: •...

  • Page 37: Adding Paper To The Cassette

    2.6.1 Adding Paper to the Cassette Add paper to the cassette using the following procedure. 1. Check to see that the printer is not printing and that the display reads 00 READY (or 11 PAPER OUT) before removing the paper cassette. CAUTION: Do not remove the paper cassette while the printer is printing.
  • Page 38 3. Remove the cassette cover by lifting it off. Fig 2-12, MLO-004838 4. Insert paper into the left side of the cassette first, being sure it is inserted below the paper guide and maximum height guard. To prevent paper jams, do not load too much paper into the cassette. Leave a small amount of space between the paper and the maximum height guard.
  • Page 39 5. Replace the cover on the cassette. Fig 2-14, MLO-004840 Operating Information 2–13...
  • Page 40 6. Insert the paper cassette into the printer. — The Alarm indicator shuts off. — The display reads 00 READY. Fig 2-15, MLO-004370 2–14 Operator’s Guide...

  • Page 41: Loading Preprinted Media

    2.7 Loading Preprinted Media To print forms, letterhead paper, or punched paper in simplex mode, load the media faceup, with the top edge of the paper nearest to the printer. 2.8 Feeding Media Manually The paper feed guide on the cover of the cassette enables you to manually feed paper, labels, transparencies, and envelopes into the printer.

  • Page 42: Legal-Size Coding Example

    For paper sizes other than A4 or letter, you must use commands from the host computer that tell the printer the paper size you are using. These commands tell the printer where to print on the page. An example of this would be printing on legal-size paper.

  • Page 43: Manually Feeding Paper, Labels, And Transparencies

    Reference Manual and Digital ANSI-Compliant Printing Protocol Level 3 Programming Supplement. Section 2.8.1 describes how to feed media using on the control Manual Feed panel to invoke the manual feed mode. See Chapter 4 for information about setting the manual feed value from the FEEDER menu. 2.8.1 Manually Feeding Paper, Labels, and Transparencies Use the following procedure to manually feed paper, labels, and transparencies.
  • Page 44 2. Fold out the extension tray. Fig 2-17, MLO-004836 2–18 Operator’s Guide...
  • Page 45 3. Press to place the printer off line. On Line — The On Line indicator shuts off. 4. Press (once or twice) until the display reads Manual Feed FEEDER = Manual. — After about 3 seconds the display will read 00 READY. —...
  • Page 46 8. Insert a single sheet of paper, labels, or a transparency into the printer until it stops. — The paper is automatically fed into the printer. — The printed paper is sent to the preselected output paper tray. NOTE: It is advisable to remove transparencies from the rear output tray as each one is printed.
  • Page 47 10. Press to place the printer off line. On Line — The On Line indicator shuts off. 11. Press twice until the display reads FEEDER = Cass. Manual Feed — After about 3 seconds the display will read 00 READY. —...
  • Page 48 14. Close the rear output tray. Fig 2-21, MLO-004834 2–22 Operator’s Guide...

  • Page 49: Using Duplex Printing

    2.9 Using Duplex Printing The manual feed functionality of the DEClaser 2100 plus printer allows you to do duplex (two-sided) printing. Since the paper must pass through the printer twice to perform two-sided printing, consider these additional cautions when making duplex prints.
  • Page 50 1. Open the rear output tray. Fig 2-23, MLO-004835 2. Fold out the extension tray. Fig 2-24, MLO-004836 2–24 Operator’s Guide...
  • Page 51 3. Press to place the printer off line. On Line — The On Line indicator shuts off. 4. Press (once or twice) until the display reads Manual Feed FEEDER = Manual. — After about 3 seconds the display will read 00 READY. —...
  • Page 52 7. Adjust the manual feed guides to accept the width of the paper. Fig 2-25, MLO-004841 8. Insert a single sheet of paper into the printer until it stops. — The paper is automatically fed into the printer. — The printed paper is sent to the rear output paper tray. Fig 2-26, MLO-004842 2–26 Operator’s Guide...
  • Page 53 9. Take the printed paper from the rear output tray and insert it into the printer printed side down when PF FEED xxx is displayed. Fig 2-27, MLO-004845 10. Continue feeding paper until the Data indicator light shuts off and the display reads 00 READY.
  • Page 54 14. Fold in the extension tray. Fig 2-28, MLO-004833 15. Close the rear output tray. Fig 2-29, MLO-004834 2–28 Operator’s Guide...

  • Page 55: Feeding Envelopes Manually

    Section 2.8 contains an example using escape sequences to set up your files to print in a particular area. Appendix A contains a listing of DEClaser 2100 plus commands and programming information for the experienced programmer.
  • Page 56 1. Open the rear output tray. Fig 2-30, MLO-004835 2. Fold out the extension tray. Fig 2-31, MLO-004836 2–30 Operator’s Guide...
  • Page 57 3. Press to place the printer off line. On Line — The On Line indicator shuts off. 4. Press (once or twice) until the display reads Manual Feed FEEDER = Manual. — After about 3 seconds the display will read 00 READY. —...
  • Page 58 7. Adjust the manual feed guides to accept the width of the envelope. Fig 2-32, MLO-004846 8. Insert a single envelope into the printer until it stops. — The envelope is automatically fed into the printer. — The printed envelope is sent to the rear output tray. Fig 2-33, MLO-004847 2–32 Operator’s Guide...
  • Page 59 9. Wait until PF FEED xxx is displayed and insert another envelope. 10. Continue feeding envelopes until the Data indicator light shuts off and the display reads 00 READY. If you want to continue to manually feed envelopes after the display reads 00 READY, go to step 6.
  • Page 60 14. Fold in the extension tray. Fig 2-34, MLO-004833 15. Close the rear output tray. Fig 2-35, MLO-004834 2–34 Operator’s Guide...

  • Page 61: Adjusting The Print Density

    2.11 Adjusting the Print Density Print density is the term used to describe the relative thickness of the line used to print characters. The thickness of a line is known as the line weight. The print density adjustment controls the amount of toner applied to the paper to make the line weight thinner or thicker.
  • Page 62 2. Lift the top cover open to the halfway position. Fig 2-37, MLO-004848 3. Rotate the print density adjustment dial so that the desired density number is opposite the index triangle. Numbers on the dial are displayed in increments of 2. Number 1 is the darkest setting;...
  • Page 63 4. Close the top cover by gently lowering the cover and pushing down on the hand grip until the cover latches securely in place. Fig 2-39, MLO-004366 Operating Information 2–37...

  • Page 64: Printing The Engine Test Print

    2.12 Printing the Engine Test Print The Engine Test Print (Figure 2–1) is used to check the printer’s paper feed mechanism for proper operation, and to check toner dispersion and line weight. The area between the lines on the Engine Test Print should be free of excess toner or smudges, and the lines should print cleanly across the entire page with no faded areas.

  • Page 65: Engine Test Print

    Figure 2–1: Engine Test Print Fig 2-40, MLO-004525 Operating Information 2–39...
  • Page 66 1. Check to be sure the printer has stopped printing and the message display reads 00 READY. 2. Press the test button on the right side of the printer with a ballpoint pen. — The printer enters the offline state. —...

  • Page 67: Printing Test Print A

    2.13 Printing Test Print A Test Print A (Figure 2–2) lists the current printer settings along with information such as total page count and the amount of free memory available. Operating Information 2–41...

  • Page 68: Test Print A

    Figure 2–2: Test Print A Fig 2-42, MLO-004851 2–42 Operator’s Guide...

  • Page 69: Test Print A

    You can print Test Print A to check the current printer settings before making changes in Menu Mode (see Chapter 4). Table 2–2 describes the items on Test Print A, and Table 2–3 decribes how to print the test print. Table 2–2: Test Print A Item Description...

  • Page 70: Printing Test Print A

    Use the following procedure to print a copy of Test Print A. Table 2–3: Printing Test Print A Operation Display Reads 1. Press to place the 00 READY On Line printer off line. — The On Line indicator shuts off. 2.

  • Page 71: Printing Test Print B

    2.14 Printing Test Print B Test Print B (Figure 2–3) contains sample printouts of the character sets that can be examined for print quality. Operating Information 2–45...

  • Page 72: Test Print B

    Figure 2–3: Test Print B Fig 2-43, MLO-004852 2–46 Operator’s Guide...

  • Page 73: Printing Test Print B

    Test Print B is printed continuously (until instructed to stop) so it can also be used to test paper feed, paper delivery, and other mechanical functions of the printer. Use the procedure in Table 2–4 to print a copy of Test Print B. Table 2–4: Printing Test Print B Operation Display Reads...

  • Page 74: Printing The Font List

    2.15 Printing the Font List Figure 2–4 shows the Font List, which contains a listing of all the available character sets in the printer, along with a sample of the available fonts. 2–48 Operator’s Guide...

  • Page 75: Font List

    Figure 2–4: Font List Fig 2-44, MLO-004853 Operating Information 2–49...

  • Page 76: Printing The Font List

    The Font List includes internal fonts, cartridge fonts, and fonts that have been downline loaded into memory. You can select fonts only by using commands from the host computer; you cannot select them from the control panel. For information about selecting fonts, refer to the Digital ANSI-Compliant Printing Protocol Level 3 Programming Reference Manual and the Digital ANSI-Compliant Printing Protocol Level 3 Programming Supplement.

  • Page 77: Using Control Representation Mode

    2.16 Using Control Representation Mode The Control Representation Mode is used to print out unprocessed data or commands sent from the host computer. This procedure is sometimes referred to as ‘‘dumping.’’ The printing of unprocessed data (in the form of characters and symbols) is convenient for debugging programs. If a specified character is undefined, a hexadecimal representation is printed in its place.

  • Page 78: Resetting The Printer

    2.17 Resetting the Printer There are two methods of resetting the printer: • You can perform a hard reset by powering the printer off and then back on. • You can perform a soft reset by pressing Reset Perform a soft reset of the printer under the following circumstances: •...

  • Page 79: Emulation Mode Of Operation

    2.18 Emulation Mode of Operation The DEClaser 2100 plus operates using DEC PPL3 mode. If you have an optional emulation cartridge installed, select Emulation Mode to invoke a protocol from the cartridge. Use the procedure in Table 2–8 to select Emulation Mode.

  • Page 80: Chapter 3 The Control Panel

    Chapter 3 The Control Panel The control panel consists of a liquid crystal display (LCD), indicator lights, and a keypad. The keypad allows you to perform certain printer functions such as printing test pages or configuring the printer menus. This chapter explains the features and uses of the control panel.

  • Page 81: Control Panel

    Table 3–1: Control Panel Functions Item Function Keypad Some keys on the keypad perform a dual function depending on whether the printer is in Keypad Mode or Menu Mode. In Keypad Mode, the keys perform the primary function labeled on the key such as Test/Font or Manual Feed.
  • Page 82 Table 3–1 (Cont.): Control Panel Functions Item Function Data indicator (green) Indicates the status of the data sent to the printer. On: Data is being printed or is still in the print buffer. If the indicator is on and the printer is not printing, the last page needs to be printed.

  • Page 83: Using The Keypad In Keypad Mode

    3.1 Using the Keypad in Keypad Mode Some keys on the keypad perform a dual function, depending on whether the printer is in Keypad Mode or Menu Mode. In Keypad Mode, the keys perform the primary function labeled on the key, such as Test/Font or Manual Feed.

  • Page 84: The Control Panel

    Form Feed pressed again to resume printing. The DEClaser 2100 plus printer alerts you to certain error Error Skip conditions by stopping the printer and displaying the type of error on the control panel. When this happens you...

  • Page 85: Using The Keypad In Menu Mode

    Table 3–3 (Cont.): Keypad Functions: Keypad Mode Function Pressing for about 3 seconds performs a soft reset Reset Reset by clearing the data in the print buffer and returning the printer to the ready state. The printer operates with the values in operating memory and any values currently stored in RAM, which are loaded into operating memory when a reset is performed.

  • Page 86: Chapter 4 Printer Configuration

    You configure the DEClaser 2100 plus printer by selecting an appropriate set of values from a group of printer setup menus. You make these selections while the printer is in Menu Mode.

  • Page 87: Entering Menu Mode

    You can access some menu features by using commands from the host computer; you can select others only from the control panel. This chapter describes how to select features using the control panel. For information about selecting features using commands from the host computer, see the Digital ANSI-Compliant Printing Protocol Level 3 Programming Reference Manual and the Digital ANSI-Compliant Printing Protocol Level 3 Programming Supplement.

  • Page 88: Using The Keypad In Menu Mode

    4.1.1 Using the Keypad in Menu Mode Table 4–2 describes the function of the Menu Mode keys. After reading the description of the Menu Mode keys, you may want to try using the keys to better understand their funtionality. See Section 4.4.1 for an example that uses the Menu Mode keys to configure the printer.

  • Page 89: Reading The Display In Menu Mode

    NOTE: The menu names on the message display are written to accommodate all protocols available on the DEClaser 2100 plus printer (ANSI, PostScript, or CaPSL). Depending on the protocol being used, the menu names that appear on the message display may not read exactly as they do on Test Print A.

  • Page 90: Displaying Menu Values

    Figure 4–2: Menu Display LOAD< -ROM FONT/FEED LAYOUT COPY/OVERLAY 16 Characters Press to scroll to the left Press to scroll to the right LOAD< -ROM FONT/FEED LAYOUT COPY/OVERLAY MLO-004919 This manual shows items from the scrolling menus and features as they are displayed (uppercase, lowercase, or initial capitals) with the selected item shown in bold type for clarification.

  • Page 91: Printer Configuration Memory

    4.3 Printer Configuration Memory Printer configuration uses four types of memory: an operating memory that contains the currently selected values, and three storage memories in which values are stored or saved. These memories are known as ROM (read- only memory), RAM (random-access memory), and NVRAM (nonvolatile random-access memory).

  • Page 92: Operating Memory

    4.3.1 Operating Memory The printer operates using the currently selected values contained in operating memory. When the printer is powered on, it loads the values stored in NVRAM into operating memory. When you select new values (through escape sequences or from the control panel), they are placed in operating memory and become part of the printer settings that are currently in use.

  • Page 93: Rom (Read-Only Memory)

    4.3.2 ROM (Read-Only Memory) ROM contains default values that are set at the factory. They are called default values because they are stored in ROM and cannot be changed. You can load these default values into operating memory while in Menu Mode using the procedure shown in Table 4–3.

  • Page 94: Nvram (Nonvolatile Random-Access Memory)

    4.3.3 NVRAM (Nonvolatile Random-Access Memory) The printer can communicate with many systems using the factory default settings in ROM, but you may have to change values to accommodate your particular application or host computer. NVRAM allows those changes to be saved in a nonvolatile memory so that they are available each time you power on the printer.

  • Page 95: Ram (Random-Access Memory)

    4.3.4 RAM (Random-Access Memory) RAM is a temporary memory area that stores selected values until the printer is powered off. It is useful to store features in RAM when you need to change settings for specific print jobs. To save values in RAM while in Menu Mode, use the procedure in Table 4–5.

  • Page 96: Operational Flow Chart

    Figure 4–4: Operational Flow Chart Place the Printer Off Line Enter Menu Mode Select the Menu Select the Feature Change the Value Settings Save Save Settings in Memory Place the Printer Back On Line MLO-004946 Printer Configuration 4–11...

  • Page 97: Sample Procedure For Changing And Saving Values

    4.4.1 Sample Procedure for Changing and Saving Values This section contains an example of how to change and save values in Menu Mode. Use the steps in Table 4–6 to perform the following tasks: • Enter Menu Mode • Change page offset values of X and Y in the LAYOUT menu from •...
  • Page 98 Table 4–6 (Cont.): Changing and Saving Values Operation Display Reads 6. Press until the offsetX -10.0 value equals -10.0. NOTE: The value decreases in steps of 0.5. 7. Press to enter offsetX =-10.0 (momentarily) Enter the new value. offsetX offsetY 8.
  • Page 99 Table 4–6 (Cont.): Changing and Saving Values Operation Display Reads 15. Press to exit 00 READY On Line Menu Mode. — The On Line indicator lights. Verification To verify that the offset distances have been changed, print a copy of Test Print A and compare it with the copy made before the changes.

  • Page 100: Test Print A

    Figure 4–5: TEST PRINT A Verification MLO-004857 Note: This does not exist in the art package, however it is the art that I need. I don’t want 4851 here. Printer Configuration 4–15...

  • Page 101: Menu Descriptions

    4.5 Menu Descriptions This section describes the printer menus, features, and values. Table 4–7 for a complete listing of all menus and parameters. Table 4–7: Menu Mode Features and Values Menu Features Values FEEDER feeder Cass. Manual LAYOUT offsetX -10.0 +0.0 +10.0 offsetY...
  • Page 102 Table 4–7 (Cont.): Menu Mode Features and Values Menu Features Values paint Partial Full Dual paper Letter INTERFACE RS232C CENTRO Optional I/O baud 1200 2400 4800 9600 19200 rsmode 7OSS 7ESS Fix-H Ready-H xon/xoff etx/ack Factory default setting. Cannot be selected using a command from the host. Selectable from the control panel only. Factory default setting for North America.

  • Page 103: Feeder Menu

    4.5.1 FEEDER Menu The FEEDER menu determines whether paper is fed manually or automatically from the cassette. You can also select the paper feed selection using the key on the control panel. See Table 3–3 for more Manual Feed information about using the key.

  • Page 104: Layout Menu

    4.5.2 LAYOUT Menu The features of the LAYOUT menu shown in Table 4–9 allow you to make adjustments to the print position (the distances from the edges of the paper where printing begins), and to set the new line so that print wraps when it reaches the right margin.

  • Page 105: Offset Position (Offsetx, Offsety)

    4.5.2.1 Offset Position (offsetX, offsetY) The offset feature of the LAYOUT menu allows you to make fine adjustments to the printing coordinates. Since the DEClaser 2100 plus printer is a page printer, it is not possible to adjust the print position by manually shifting the position of the page.

  • Page 106: Offset Printout Samples

    Figure 4–7 shows sample printouts of Test Print A that use different offset values. Figure 4–7: Offset Printout Samples MLO-004858 Printer Configuration 4–21...

  • Page 107: Automatic New Line (Autonl)

    4.5.2.2 Automatic New Line (autoNL) The autoNL feature determines whether or not the printer wraps to the next line when it reaches the right margin. 4.5.3 COPY Menu The COPY menu (Table 4–10) determines the number of copies to be printed.

  • Page 108: Initial Menu

    4.5.5 INITIAL Menu The INITIAL menu (Table 4–12) combines the macro, paint, and paper size features. You can save settings from this menu only in NVRAM. To activate the settings, perform a reset after changing them. Table 4–12: INITIAL Menu Features and Values Feature Values Description...

  • Page 109: Macro

    4.5.5.1 Macro The macro feature allows you to select an environment for local compatibility. It assigns the proper User Preference character set, enables and disables the initialization message, and specifies a return response (device identification) when a Device Attributes (DA) request is received. The macro feature is slightly different from other menu features because three parameters (device ID, initialization message, and User Preference character set) are added together to determine the macro value.

  • Page 110: Examples Using The Macro Feature

    Disabled Enabled Factory default setting. The DEClaser 2100 plus printer can identify itself as a Digital ANSI- Compliant Printing Protocol level 3 printer, and therefore can be recognized as such by symbionts and terminal drivers that conform to Digital ANSI- compliant architecture.

  • Page 111: Paint Mode (Paint)

    4.5.6 INTERFACE Menu The correct interface connection is necessary for the printer to communicate properly with the host computer. The DEClaser 2100 plus printer supports both parallel and serial interface connections. The interface must match the type used by the host computer.
  • Page 112 Table 4–17: INTERFACE Menu Features and Values Feature Values Description RS232C Selects the RS232C serial interface to communi- cate with the host computer. Select this value if your computer uses a serial interface. When you select the serial interface, you must select values for all the other features in this menu (baud rate, rsmode, and so on).

  • Page 113: Interface Selection (I/F)

    Table 4–17 (Cont.): INTERFACE Menu Features and Values Feature Values Description 7 data bits Odd parity check 1 stop bit 8 data bits No parity check 2 stop bits Fix-H Sets the DTR line to a fixed high signal. Ready-H Sets the DTR line to a high signal when the printer is ready to receive data.

  • Page 114: Baud Rate (Baud)

    4.5.6.2 Baud Rate (baud) The baud rate (baud) feature sets the transmit and receive speed the printer uses to communicate with the host computer. The printer speed must match the speed used by the host computer. 4.5.6.3 RS232C Data Format (rsmode) The RS232C data format (rsmode) feature determines the data format the printer uses to communicate with the host computer.

  • Page 115: End Of Text/Acknowledge (Etx/Ack)

    4.5.6.6 End of Text/Acknowledge (etx/ack) The end of text/acknowledge (etx/ack) feature is another type of handshaking protocol on some systems to prevent data overflow. etx/ack feature also uses software to regulate the flow of data to the input buffer by exchanging signals with the host computer. It is recommended that this feature be enabled by systems that support etx/ack to prevent the loss of data.

  • Page 116: Chapter 5 Print Media

    Print Media This chapter describes the print media that are appropriate for use with the DEClaser 2100 plus printer. The types of print media described in this chapter are paper, labels, transparencies, and envelopes. The DEClaser 2100 plus printer produces excellent print quality using electrophotographic laser technology.

  • Page 117: Paper Specifications

    5.1 Paper Specifications This section contains information on the sizes and specifications of plain paper that can be used with the DEClaser 2100 plus printer. Table 5–1 lists the paper sizes that can be used with the standard and optional size cassettes for the printer.

  • Page 118: Special Considerations When Printing On Paper

    Table 5–2: Paper Specifications Category Specification Paper weight: cassette feed 60 g/m to 80 g/m basis weight (16 lb. to 21 lb.) Paper weight: manual feed 60 g/m to 135 g/m basis weight (16 lb. to 35 lb.) Thickness 0.075 mm to 0.115 mm Moisture content 5% to 8% Smoothness...

  • Page 119: Envelope Specifications

    5.2 Envelope Specifications Envelopes must meet the same specifications as paper (see Table 5–2). In addition, the following types of envelopes cannot be used with the printer: • Envelopes with sealing flaps that are open Fig 5-1, MLO-005731 NOTE: I don’t know why the MLO numbers on this art changed.
  • Page 120 • Envelopes with sealing flaps at the leading and trailing edges Fig 5-2, MLO-005729 NOTE: I don’t know why the MLO numbers on this art changed. • Envelopes with three or more layers of paper at the leading and trailing edges Fig 5-3, MLO-005732 NOTE: I don’t know why the MLO numbers on this art changed.
  • Page 121 • Envelopes that have transparent windows Fig 5-4, MLO-005730 NOTE: I don’t know why the MLO numbers on this art changed. • Envelopes that have clasps, snaps, or strings Fig 5-5, MLO-005733 NOTE: I don’t know why the MLO numbers on this art changed. 5–6 Operator’s Guide...

  • Page 122: Special Considerations When Printing On Envelopes

    5.2.1 Special Considerations When Printing on Envelopes Observe the following requirements when printing on envelopes: • Feed envelopes manually (if you are not using the special envelope cassette). • Envelopes can be printed only on the front side. • Since you need to print addresses in a particular area on envelopes, you must give the printer the proper print coordinates to print the addresses.

  • Page 123: Transparency Specifications

    5.3 Transparency Specifications Table 5–3 and Table 5–4 contain information on the sizes and specifications of transparencies that can be used with the DEClaser 2100 plus printer. Table 5–3: Transparency Sizes Transparency Size Dimensions 210 mm x 297 mm Letter 8 ½...

  • Page 124: Label Specifications

    5.4 Label Specifications A label consists of a face sheet, an adhesive sheet, and a carrier sheet. The face sheet (or printing surface) is usually composed of photocopying paper and should meet the same specifications for paper as described in Table 5–2.

  • Page 125: Special Considerations When Printing On Labels

    5.4.1 Special Considerations When Printing on Labels Observe the following requirements when printing on labels: • Labels are usually fed manually. If you are feeding labels from a cassette, be sure they are high-quality labels that meet the specifications listed in Table 5–2. •...

  • Page 126: Paper Storage

    • Check to see that the paper is loaded with the correct side up. Some packages of paper have an arrow on the label that points in the direction of the top side of the paper. Load paper with this top side up. If there is no arrow on the label, check the paper for curl.

  • Page 127: Error Skip Procedure

    NOTE: The printer status messages do not require operator intervention. 6.1 Error Skip Procedure The DEClaser 2100 plus printer alerts you to error conditions by stopping the printer, placing it off line, and displaying the type of error on the control panel.

  • Page 128: Printer Status Messages

    immediately before printing can continue. You can acknowledge other types of errors and still continue printing by pressing . When these types Error Skip of errors occur, you may elect to take the long-term corrective action (for example, adding RAM or reassigning memory) at another time. Use the procedure in Table 6–1 to acknowledge the error condition and continue printing.
  • Page 129 Table 6–2 (Cont.): Printer Status Messages Message Meaning 03 RESET The printer is being reset (Section 2.17). 04 TEST STOP Test printing has stopped. 05 TEST PRINT A Test Print A is being printed (Section 2.13). 06 FONT LIST A Font List A is being printed (Section 2.15).

  • Page 130: Operator Call Messages

    6.3 Operator Call Messages Operator call messages appear if a problem with the printer requires operator intervention, such as adding paper or closing the printer cover. You should check the online/offline status of the printer after correcting a problem; you may have to place the printer back on line by pressing .

  • Page 131: Software Error Messages

    Table 6–3 (Cont.): Operator Call Messages Message Meaning Corrective Action PC LOAD LEGAL Request for a legal-size paper Install a legal-size paper cassette cassette. into the printer. The printer was not reset Reset the printer. after the cassette size was changed.

  • Page 132: Software Error Messages

    Table 6–4: Software Error Messages Message Meaning Corrective Action 20 PAGE FULL The page buffer is over- Clear fonts from memory after each flowing with data. job. Assign one or two full-page bitmap areas in memory to handle the complex data (Section 4.5.5.3).
  • Page 133 Table 6–4 (Cont.): Software Error Messages Message Meaning Corrective Action 42 ERROR There is an expansion Power off the printer and verify that interface error. any memory expansion boards are correctly installed. If the problem continues, call your Digital service representative (Chapter 8).

  • Page 134: Service Call Messages

    6.5 Service Call Messages Service call messages indicate that the printer requires servicing by a qualified Digital service representative (see Chapter 8 for service information). Service messages are displayed as XX SERVICE (where XX equals a number from 50 through 99). NOTE: Before calling for service, try to clear the error message by powering the printer off.

  • Page 135: Common Operating Problems

    Table 6–5: Common Operating Problems Problem Possible Cause Corrective Action NO POWER The printer does not The power source is Make sure the power cord is power up when you set defective. plugged into the wall outlet. the power switch Check that there is power at the to the ON position.
  • Page 136 Table 6–5 (Cont.): Common Operating Problems Problem Possible Cause Corrective Action POOR PRINTING Large amounts of Toner is not being Remove the EP-S cartridge from vertical fade and/or dispersed evenly. the printer and gently rotate it white streaks are several times to redistribute on the page.
  • Page 137 Table 6–5 (Cont.): Common Operating Problems Problem Possible Cause Corrective Action POOR PRINTING The cleaning mechanism Replace the EP-S cartridge in the EP-S cartridge is (Section 7.3). not working properly. The overall print The print medium is not See Chapter 5 for print media quality is poor.

  • Page 138: Paper Jams

    6.7 Paper Jams Paper jams are typically caused by: • Damaged paper (torn or folded) • Improperly stored paper (excessive paper curl or humidity) • Paper that does not meet specifications (incorrect weight or heat tolorance) • Paper that is improperly loaded in the tray (not aligned properly) To reduce the chance of paper jams, you should follow the instructions for proper paper selection, storage, and loading as outlined in Chapter 5.

  • Page 139: Top And Output Paper Tray Paper Jams

    On Line back on line. When a paper jam is cleared and printing is resumed, the DEClaser 2100 plus printer automatically reprints the page that jammed. 6.7.1 Top and Output Paper Tray Paper Jams Use the following procedure to clear paper jams from the top and rear output trays.
  • Page 140 1. Open the top cover by pressing the release button forward and then down. — The top cover will release and open slightly. Fig 6-2, MLO-004891 6–14 Operator’s Guide...
  • Page 141 2. Lift the top cover open. Fig 6-3, MLO-004868 3. Push the tab on the fixing assembly back to release the paper. WARNING: Be careful when accessing areas inside the printer, because the fixing assembly may be hot. Fig 6-4, MLO-004866 Troubleshooting 6–15...
  • Page 142 4. Remove the jammed paper from the printer by pulling it out from the output tray. Fig 6-5, MLO-004892 6–16 Operator’s Guide...
  • Page 143 5. Close the top cover by gently lowering the cover and pushing down on the hand grip until the cover latches securely in place. — The printer initializes (recycles). — The Alarm and Data indicators shut off. — The message display reads 00 READY. Fig 6-6, MLO-004366 6.

  • Page 144: Paper Feed, Transfer, And Fixing Assembly Paper Jams

    6.7.2 Paper Feed, Transfer, and Fixing Assembly Paper Jams Use the following procedure to clear paper jams from the paper feed, transfer, and fixing assembly areas. 1. Open the top cover by pressing the release button forward and then down. —...
  • Page 145 3. If paper is jammed in the feed or transfer area, lift the transfer guide (green handle) to release the paper and remove the paper from the printer. If the jammed paper did not reach the feed area, remove the cassette and pull the paper out from the cassette slot.
  • Page 146 4. If paper is jammed in the fixing assembly, push the green tab on the fixing assembly down to release the paper, and remove the paper from the printer. WARNING: Be careful when accessing areas inside the printer, because the fixing assembly may be hot. Fig 6-10, MLO-004870 6–20 Operator’s Guide...
  • Page 147 5. Close the top cover by gently lowering the cover and pushing down on the hand grip until the cover latches securely in place. — The printer initializes (recycles). — The Alarm and Data indicators shut off. — The message display reads 00 READY. Fig 6-11, MLO-004366 6.

  • Page 148: Chapter 7 Maintenance

    Chapter 7 Maintenance To obtain optimum performance from the DEClaser 2100 plus printer, you must perform the prescribed care and maintenance as outlined in this chapter. This chapter describes how to properly maintain the printer and covers the following topics: •...

  • Page 149: Cleaning The Internal Surfaces

    7.1.1 Cleaning the Internal Surfaces Clean the transfer and paper feed areas inside the printer using the following procedure. 1. Be sure the printer is not printing and the display reads 00 READY. 2. Press the power switch on the back of the printer to the O (OFF) position.
  • Page 150 3. Press the release button forward and then down. — The top cover releases and opens slightly. Fig 7-2, MLO-004830 4. Lift the top cover open. Fig 7-3, MLO-004868 Maintenance 7–3...
  • Page 151 5. Wipe the paper feed area (black plastic) clean with a cloth dampened with water. WARNING: Be careful when accessing areas inside the printer, because the fixing assembly may be hot. Fig 7-4, MLO-004871 7–4 Operator’s Guide...
  • Page 152 6. Wipe the following items clean in the transfer area with the dampened cloth: • The movable transfer guide (with green handle) and clear plastic strip • The metal transfer roller • The silver-colored metal transfer guide Fig 7-5, MLO-004872 Maintenance 7–5...
  • Page 153 7. Gently close the top cover by pushing down on the hand grip until the cover locks into place. Fig 7-6, MLO-004366 7–6 Operator’s Guide...

  • Page 154: Cleaning The Primary Corona Wire

    7.1.2 Cleaning the Primary Corona Wire The primary corona wire is located inside the EP-S cartridge. A dirty primary corona wire can cause black streaking to occur on the paper, and should be cleaned to correct this problem. 1. Be sure the printer is not printing and the display reads 00 READY.
  • Page 155 3. Press the release button forward and then down. — The top cover releases and opens slightly. Fig 7-8, MLO-004830 4. Open the top cover halfway. Fig 7-9, MLO-004848 7–8 Operator’s Guide...
  • Page 156 5. Remove the EP-S cartridge by pulling it out from the top cover. Fig 7-10, MLO-004890 6. Remove the wire/pin cleaner from the inside of the printer. WARNING: Be careful when removing the wire/pin cleaner from the printer, because the fixing assembly may be hot. Fig 7-11, MLO-004873 Maintenance 7–9...
  • Page 157 7. Insert the felt end of the wire/pin cleaner into either end of the EP-S cartridge slot. CAUTION: Do not insert the brush end of the wire/pin cleaner into the slot. Inserting the brush end can damage the corona wire. Fig 7-12, MLO-004875 8.
  • Page 158 9. Return the wire/pin cleaner to its storage location in the printer. Fig 7-14, MLO-004873 10. Install the EP-S cartridge into the top cover. Fig 7-15, MLO-004889 Maintenance 7–11...
  • Page 159 11. Gently close the top cover by pushing down on the hand grip until the cover locks into place. Fig 7-16, MLO-004366 7–12 Operator’s Guide...

  • Page 160: Cleaning The Transfer Corona Wires And Discharging Pins

    7.1.3 Cleaning the Transfer Corona Wires and Discharging Pins The transfer corona wires and discharging pins are part of the paper transfer area inside the printer. Normally, you clean these corona wires and discharging pins each time you replace the EP-S cartridge, but you may find it necessary to clean them between cartridge replacements if you experience problems with print quality.
  • Page 161 3. Press the release button forward and then down. — The top cover releases and opens slightly. Fig 7-18, MLO-004830 4. Lift the top cover open. Fig 7-19, MLO-004868 7–14 Operator’s Guide...
  • Page 162 5. Remove the wire/pin cleaner from the inside of the printer. WARNING: Be careful when removing the wire/pin cleaner from the printer, because the fixing assembly may be hot. Fig 7-20, MLO-004873 Maintenance 7–15...
  • Page 163 6. Clean the discharging pins (in the groove) using the brush end of the cleaner. CAUTION: You must lift the brush over the separation wires as you clean along the groove. Be careful not to break the wires as you clean the discharging pins.
  • Page 164 7. Return the wire/pin cleaner to its storage location in the printer. Fig 7-22, MLO-004873 Maintenance 7–17...
  • Page 165 8. Clean the transfer corona wire and the nylon separation wires with the cotton swab. CAUTION: The corona wire and nylon separation wires are fragile. Do not press down too hard on the wires. Fig 7-23, MLO-004877 9. Gently close the top cover by pushing down on the hand grip until the cover locks into place.

  • Page 166: Extending Ep-S Cartridge Life

    7.2 Extending EP-S Cartridge Life Each EP-S cartridge contains a photosensitive drum and toner, assuring you of optimum print quality throughout the life of the cartridge. When the cartridge runs out of toner, you replace it with a new one. CAUTION: The use of refilled EP-S cartridges is not recommended and may have an adverse effect on print quality.

  • Page 167: Replacing The Ep-S Cartridge

    7.3 Replacing the EP-S Cartridge When the 16 TONER LOW message is displayed, it means that the printer is either running out of toner or the toner is not being distributed evenly. Before replacing the EP-S cartridge, make sure that the toner is really depleted.
  • Page 168 To replace the EP-S cartridge, follow the instructions that come with the cartridge or use the following procedure. 1. Be sure the printer is not printing and the display reads 00 READY. 2. Press the power switch on the back of the printer to the O (OFF) position.
  • Page 169 3. Press the release button forward and then down. — The top cover will release and open slightly. Fig 7-27, MLO-004830 4. Open the top cover to its halfway position. Fig 7-28, MLO-004848 7–22 Operator’s Guide...
  • Page 170 5. Remove the EP-S cartridge by pulling it out from the top cover. Open the top cover to its full upright position after removing the cartridge. Fig 7-29, MLO-004890 Maintenance 7–23...
  • Page 171 6. Open the green fixing assembly cover. WARNING: The fixing assembly may be hot. Be careful when accessing the fixing unit. Fig 7-30, MLO-004354 7–24 Operator’s Guide...
  • Page 172 7. Remove the used fixing roller cleaner from the fixing assembly. Discard the used fixing roller cleaner. Fig 7-31, MLO-004879 8. Wipe the fixing roller with the cleaning pad on the end of the new cleaner. Fig 7-32, MLO-004355 Maintenance 7–25...
  • Page 173 9. Peel off the cleaning pad and discard it. Fig 7-33, MLO-004356 10. Insert the new cleaner into the fixing assembly. Fig 7-34, MLO-004357 7–26 Operator’s Guide...
  • Page 174 11. Close the fixing assembly cover. NOTE: The fixing assembly cover does not close tightly. Fig 7-35, MLO-004358 Maintenance 7–27...
  • Page 175 12. Wipe the paper feed area (black plastic) clean with a cloth dampened with water. CAUTION: To prevent possible damage to the internal and external surfaces of the printer, do not use cleaners or solvents. Use a clean cloth dampened with water only. Fig 7-36, MLO-004871 7–28 Operator’s Guide...
  • Page 176 13. Wipe the transfer area clean with the dampened cloth. The transfer area consists of the following components: • The movable transfer guide (with green handle) and clear plastic strip • The metal transfer roller • The silver-colored metal transfer guide Fig 7-37, MLO-004872 Maintenance 7–29...
  • Page 177 14. Clean the transfer corona wire and the nylon separation wires with the cotton swab. CAUTION: The corona wire and nylon separation wires are fragile. Do not press down on the wires too hard or they may break. Fig 7-38, MLO-004877 15.
  • Page 178 16. Clean the discharging pins in the groove, using the brush end of the cleaner. CAUTION: You must lift the brush over the separation wires as you clean along the groove. Be careful not to break the wires as you clean the pins.
  • Page 179 17. Return the wire/pin cleaner to its storage location in the printer. Fig 7-41, MLO-004873 18. Rock the new EP-S cartridge five or six times as shown to distribute the toner evenly. Fig 7-42, MLO-004362 7–32 Operator’s Guide...
  • Page 180 19. Lower the top cover to its partially opened position and install the new cartridge. Fig 7-43, MLO-004889 20. Snap the tab from the left side of the cartridge by moving it up and down. Fig 7-44, MLO-004364 Maintenance 7–33...
  • Page 181 21. Grasp the tab and pull the sealing tape completely out of the cartridge. Discard the sealing tape. NOTE: The sealing tape is about 55 cm (22 in.) long and may have toner on it. If you get toner on your hands or clothing, wash them with cold water and soap.
  • Page 182 22. Close the top cover by pushing down on the hand grip until it snaps into place. Fig 7-46, MLO-004366 Maintenance 7–35...

  • Page 183: Replacing The Ozone Filter

    7.4 Replacing the Ozone Filter The DEClaser 2100 plus printer is equipped with a disposable ozone filter that must be replaced after each 100,000 printed pages. See Appendix B for ordering information. Use the following procedure to replace the ozone filter.
  • Page 184 3. Press the release button forward and then down. — The top cover will release and open slightly. Fig 7-48, MLO-004830 4. Lift the top cover open all the way. Fig 7-49, MLO-004868 Maintenance 7–37...
  • Page 185 5. Pull down the ozone filter cover to access the filter. WARNING: The fixing assembly may be hot. Be careful when accessing the ozone filter. Fig 7-50, MLO-004880 6. Remove the filter by pulling it out by its tab. Fig 7-51, MLO-004881 7–38 Operator’s Guide...
  • Page 186 7. Grasp the new filter by its tab and slide it into place. CAUTION: Always handle the filter by its tab and not by its mesh sides. The mesh sides are fragile and can be damaged easily. Fig 7-52, MLO-004882 8.

  • Page 187: Chapter 8 Service

    Chapter 8 Service If you cannot correct a problem with the DEClaser 2100 plus printer, request servicing by a qualified Digital service representative. This chapter lists the available services. 8.1 Digital Equipment Corporation Services Digital Equipment Corporation provides a wide range of maintenance programs for printers.

  • Page 188: Questions To Consider Before You Call

    For more information on any of Digital Equipment Corporation’s maintenance services, call the Digital Services office in your area during normal business hours. Refer to the list of questions in Table 8–1 before calling the service center. Table 8–1: Questions to Consider Before You Call Is the call necessary? Check Chapter 6.

  • Page 189: Appendix A Declaser Printer Quick Reference Guide

    Appendix A DEClaser Printer Quick Reference Guide This quick reference guide contains basic information on using certain programming instructions with your DEClaser printer. For quick reference use, see these sections: Category Section Positioning Controls Margins and Spacing Set/Reset Modes Fonts and Character Sets Miscellaneous For detailed information about sending commands from the host computer, consult the Digital ANSI-Compliant Printing Protocol Level 3 Programming...
  • Page 190 Conventions The following conventions are used throughout this appendix. Convention Meaning The is the control character (9/11) used to introduce the Control Sequence Introducer as part of the format of a DEC PPL3 command. For example, . Both parameter characters and intermediate characters are CSI Pn A supported in a CSI control sequence.

  • Page 191: Positioning Controls

    A.1 Positioning Controls CUU—Cursor Up CSI Pn A Where: Pn = n Is the numeric value according to the Select Size Unit (SSU) sequence and Positioning Unit Mode (PUM) setting. (A value of 0 is treated as one vertical position up.) DECCAHT—Clear All Horizontal Tabs ESC 2 Clears all horizontal tab stops.
  • Page 192 HPA—Horizontal Position Absolute CSI Pn ‘ Where: Pn = 0 Is treated as horizontal position 1. Pn = n Is the numeric value according to the SSU sequence and PUM setting. HPB—Horizontal Position Backward CSI Pn j Where: Pn = 0 Is treated as one horizontal position to the left.
  • Page 193 VPA—Vertical Position Absolute CSI Pn d Where: Pn = 0 Is treated as vertical position 1. Pn = n Is the numeric value according to SSU sequence and PUM setting. VPB—Vertical Position Backward CSI Pn k Where: Pn = 0 Is treated as one vertical position up.

  • Page 194: Margins And Spacing

    A.2 Margins and Spacing DECSHORP—Set Horizontal Pitch CSI Ps w Where: Ps = 0 Is determined by current font. Ps = 1 Is 720 centipoints (10 characters/inch). Ps = 2 Is 600 centipoints (12 characters/inch). Ps = 3 Is 545 centipoints (13.2 characters/inch). Ps = 4 Is 436 centipoints (16.5 characters/inch).
  • Page 195 DECSLRM—Set Left and Right Margins CSI Pn1 ; Pn2 s Where: Pn1 = n Is the left margin-setting numeric value according to the SSU sequence and PUM setting (Pn1 = 0 is treated as 1). Pn2 = n Is the right margin-setting numeric value according to the SSU sequence and PUM setting (Pn2 = 0 is treated as 1).
  • Page 196 DECVERP—Set Vertical Pitch CSI Ps z Where: Ps = 0 Is determined by the current font. Ps = 1 Is 1200 centipoints (6 lines/inch). Ps = 2 Is 900 centipoints (8 lines/inch). Ps = 3 Is 600 centipoints (12 lines/inch). Ps = 4 Is 3600 centipoints (2 lines/inch).

  • Page 197: Decvpfs Numeric Parameters

    DECVPFS—Variable Page Format Select CSI Ps1 ; Pn2 ; . . . ; Pn11 SP z Where: Ps1 = 0, 1 Is portrait orientation. Ps1 = 2 Is landscape orientation. Ps1 = Other Is portrait orientation. Table A–1: DECVPFS Numeric Parameters Meaning If ‘‘Zero’’...
  • Page 198 GSS—Graphic Size Select CSI Pn SP C Where: Pn = 0 Is 10 points. Pn = n Is the font height according to SSU sequence. PFS—Page Format Select CSI Ps SP J Where: Ps = 0 Portrait normal text. Ps = 1 Landscape normal text.
  • Page 199 SHS—Set Horizontal Spacing CSI Ps SP K Where: Ps = 0 Is 720 centipoints (10 characters/inch). Ps = 1 Is 600 centipoints (12 characters/inch). Ps = 2 Is 480 centipoints (15 characters/inch). Ps = 3 Is 1200 centipoints (6 characters/inch). SPI—Spacing Pitch Increment CSI Pn1 ;...

  • Page 200: Set/Reset Modes

    SVS—Set Vertical Spacing CSI Ps SP L Where: Ps = 0 Is 1200 centipoints (6 lines/inch). Ps = 1 Is 1800 centipoints (4 lines/inch). Ps = 2 Is 2400 centipoints (3 lines/inch). Ps = 3 Is 600 centipoints (12 lines/inch). Ps = 4 Is 900 centipoints (8 lines/inch).
  • Page 201 DECCRNLM—Carriage Return/New Line Mode Set—CR acts as New Line. CSI ? 40 h CSI ? 40 l Reset—CR acts as Carriage Return. DECOPM—Origin Placement Mode CSI ? 52 h Sets Origin Placement Mode. Resets Origin Placement Mode. CSI ? 52 l DECPSM—Horizontal Pitch Select Mode CSI ? 29 h Sets Horizontal Pitch Select Mode.

  • Page 202: Fonts And Character Sets

    A.4 Fonts and Character Sets ASCEF—Announce Subset of Code Extension Facilities ESC SP Fs If the final character (Fs) is: Is ISO 4873, level 1. Is ISO 4873, level 2. Is ISO 4873, level 3. DECATFF—Assign to Type Family or Font DCS Ps1 ;...
  • Page 203 DECAUPSS—Assign User-Preference Supplemental Character Set DCS Ps ! u D . . . D ST Where: Ps = 0 Is a 94-character set. Ps = 1 Is a 96-character set. Possible D . . . D values: DEC Supplemental (Ps = 0) ISO Latin-1 Supplemental (Ps = 1) JIS Katakana...
  • Page 204 DECLFF—Load Font File DCS Ps1 ; Ps2 ; Ps3 y font_record, font_record; comment_record ST Where: Ps1 = 0 Is Digital font file format. Ps2 = 0 Is print the summary sheet. Ps2 = 1 Is do not print the summary sheet. Ps2 = 2 Is send font error and warning information.

  • Page 205: Character Set Identification

    SCS—Select Character Set ESC I* . . . In F Where: I* = ( (Left parenthesis) Designates the character set into G0. I* = ) (Right parenthesis) Designates the character set into G1. I* = * (Asterisk) Designates the character set into G2. I* = + (Plus sign) Designates the character set into G3.
  • Page 206 Table A–2 (Cont.): Character Set Identification Number of Character Set Character Set Characters Identifier DEC Swiss Norwegian/Danish ‘ DEC Supplemental DEC Technical > DEC Special Graphics DEC Portuguese User Preference Supplemental < (initial setting for G2 and G3) DEC 7-Bit Hebrew DEC Hebrew Supplemental "4 ISO Latin-1 Supplemental...
  • Page 207 SGR—Select Graphic Rendition CSI Ps ; . . . ; Ps m Where: Ps = 0 Turns off all attributes (standard and private). Ps = 1 Turns on bold. Ps = 3 Turns on italics. Ps = 4 Turns on underline. Ps = 9 Turns on strike-through.

  • Page 208: Miscellaneous

    CSI ? 73 ; 4 ; 6 ; 8 ; 9 ; 10 ; 11 ; 12 ; 16 ; 18 ; c The following is the generic response indicating a DEClaser 2100 plus printer: CSI ? 73 ; 4 ; 6 ; 8 ; 9 ; 10 ; 11 ; 12 ; 16 c...
  • Page 209 DA2R—Device Attributes (Secondary) Report CSI > Ps1 ; Ps2 ; Ps3 ; Ps4 c Where: Ps1 = 46 Identifies the DEClaser 2100 plus printer. Ps1 = 47 Identifies the DEClaser 2200 plus printer. Ps2 = xx xx is the major firmware version number multiplied by 10.
  • Page 210 DECASFC—Automatic Sheet Feeder (input tray) Control CSI Ps ! v Where: Ps = 0 No tray change. Ps = 1 Selects the top tray. Ps = 2 Selects the bottom tray (only on the DEClaser 2200 plus printer). Ps = 3 Selects the envelope feeder (only on the DEClaser 2200 plus printer).
  • Page 211 DECFSR—Font Status Report If DECRFS is 1 or 0: DCS 1 " { report_string ST If DECRFS is 2 or 0: DCS 2 " { nnn ST If DECLFF has Ps2 = 2 or 3: DCS 4 " { error_string ST Where: This Variable Indicates...
  • Page 212 DECRVEC—Draw Relative Vector CSI Ps1 ; Pn2 ; Pn3 SP | Where: Ps1 = 0 Draws a horizontal (X) line to the right. Ps1 = 1 Draws a vertical (Y) line down. Ps1 = 2 Draws a horizontal (X) line to the left. Ps1 = 3 Draws a vertical (Y) line up.
  • Page 213 DECSITF—Select Input Tray Failover CSI Ps1 ; Ps2 ; . . . Psn SP w Where: Ps1 = 0 Disables all composite input trays. Ps1 = 1 Defines composite tray 1. Ps2–Psn = n Designates the tray as a member of the composite tray. NOTE: Tray numbers are the same as in the DECASFC sequence.
  • Page 214 DECVEC—Draw Vector CSI Ps1 ; Pn2 ; Pn3 ; Pn4 ; Pn5 ! | Where: Ps1 = 0 Draws horizontal line (X). Ps1 = 1 Draws vertical line (Y). Ps1 = Other Performs no action. Pn2 = n Is the horizontal line (X) start position according to the SSU sequence. Pn3 = n Is the verical line (Y) start position according to the SSU sequence.
  • Page 215 RIS—Reset to Initial State Resets the printer to initial state values and returns to DEC PPL3 protocol. ESC c ROCS—Return from Other Coding System Returns to DEC PPL3 from an alternate protocol emulation mode. ESC % @ SOCS—Select Other Coding System ESC % 8 Selects HP PCL emulation mode.

  • Page 216: Appendix B Accessories And Supplies

    Accessories and Supplies This appendix lists some of the accessories and supplies available for the DEClaser 2100 plus printer. Contact your Digital sales representative or refer to your latest DECdirect catalog for a complete list of products and the latest pricing information. See Section B.1 for additional ordering information.
  • Page 217 Table B–1 (Cont.): DEClaser 2100 plus Printer Accessories and Supplies Part Number Description LNXX–UE 3 MB RAM module LNXX–AC EP-S Cartridge Supplies Kit (quantity = 1) LNXX–XA EP-S Cartridge Supplies Kit (quantity = 4) LNXX–XB EP-S Cartridge Supplies Kit (quantity = 16) LNXX–XC...
  • Page 218 Table B–1 (Cont.): DEClaser 2100 plus Printer Accessories and Supplies Part Number Description LN03X–AK A4-size transparencies 297 mm x 210 mm 50 sheets per box 29–28272–01 Replacement ozone filter NOTE: The replacement ozone filter is available through self-maintenance services. Call 1–800–344–4825 to order the filter.

  • Page 219: Ordering Information

    B.1 Ordering Information Use the following mailing addresses and telephone numbers to order products for the DEClaser 2100 plus printer. Table B–2: Ordering Within the U.S.A. MAIL Digital Equipment Corporation PO Box CS2008 Nashua, NH 03061 TELEPHONE Order toll free 1–800–DIGITAL (DECdirect) between the hours of 8:30 a.m.

  • Page 220: Appendix C Specifications

    Appendix C Specifications This appendix contains the operating and interface specifications for the DEClaser 2100 plus printer. C.1 Operating Specifications Type: Desktop page printer Printing Method: Electrophotographic using laser beam scanning Laser Power: 5 mW maximum Resolution: 300 dpi Printing Speed:...
  • Page 221 Built-in Font Files: The DEClaser 2100 plus has 36 built-in font files that can be used with DEC PPL3. The font files consist of four fonts and nine character sets. These fonts are: • Courier 10-point normal portrait • Courier 10.3-point normal portrait •...
  • Page 222 Power Requirements: 100–115 Vac, 50/60 Hz 220–240 Vac, 50 Hz Power Consumption: 100–115 V models = 810 W @ 115 V 220–240 V models = 790 W @ 240 V Packaged Weight: Approximately 24.0 kg (54 lb.) Installed Weight: Approximately 20.6 kg (45.5 lb.) Dimensions: Width: 454 mm (17.9 in.) Depth: 525 mm (20.7 in.)

  • Page 223: Serial Interface Specifications

    C.2 Serial Interface Specifications Table C–1 lists the pin signals for the RS232C serial interface connector. Figure C–1 shows the pin assignments on the connector. Figure C–2 and Figure C–3 show the serial connections with and without connection to a modem.

  • Page 224: Serial Connections To Modem

    Figure C–2: Serial Connections to Modem MLO-004885 Specifications C–5...

  • Page 225: Serial Connections Without Modem

    Figure C–3: Serial Connections Without Modem MLO-004887 C–6 Operator’s Guide...

  • Page 226: Parallel Interface Specifications

    C.3 Parallel Interface Specifications Table C–2 lists the pin signals for the parallel (Centronics) interface connector. Figure C–4 shows the pin assignments on the connector, and Figure C–5 shows the parallel connections to an external device. Specifications C–7...

  • Page 227: Parallel Interface Pin Assignments

    Table C–2: Parallel Interface Pin Assignments Signal Direction DataStrobe Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data 8 Busy Call (PE) Select 14–15 Not Connected – 0 Volts (Logic Ground) – Chassis Ground –...

  • Page 228: Parallel Pin Assignment

    Figure C–4: Parallel Pin Assignment MLO-004886 Figure C–5: Parallel Connections MLO-004888 Specifications C–9...

  • Page 229: Appendix D Ln03 Compatibility

    Appendix D LN03 Compatibility This appendix contains information highlighting the differences between the DEClaser 2100 plus printer and the LN03 printer. This information is directed at the differences affecting compatibility between the printers. D.1 General Differences The following list identifies the general differences between the LN03 printer and the DEClaser 2100 plus printer.

  • Page 230: Printable Area Compatibility

    When the LN03 printer encounters a character that exceeds the printable area, it attempts (in some instances) to shift the character so that it falls within the printable area. The DEClaser 2100 plus printer does not image any characters that exceed the printable area. This results in lost characters.
  • Page 231 The DEClaser 2100 plus printer enforces the Common Font File Format (CFFF) syntax and semantics more strictly than the LN03. Therefore, some fonts containing errors, which load correctly on the LN03, may not load properly on the DEClaser 2100 plus printer and will generate an error report. •...

  • Page 232: Glossary

    The type of font created from a bitmap pattern. A bitmap font has a fixed size, similar to the type set in typography. The Courier font that resides in the DEClaser 2100 plus printer is an example of a bitmap font. buffer An area in the printer’s memory used for temporary storage of data during...
  • Page 233 A value or setting the printer assumes unless specific changes are made. For example, the interface default value for the DEClaser 2100 plus printer is RS232C (serial). Default values are stored in ROM and cannot be changed.
  • Page 234 DTR is sometimes known as ‘‘hardware handshaking protocol.’’ duplex A layout indicating that a document is to be printed on two sides. The DEClaser 2100 plus printer can perform duplex printing only while in the manual feed mode of operation. EP-S cartridge Electrophotographic supply cartridge.
  • Page 235 LAYOUT menu contains features such as offsetX and offsetY, which are used to configure margins on the page. There are six menus for the DEClaser 2100 plus printer that in total constitute the current printer settings. moisture content The ratio of water to the dry mass of paper.

  • Page 236: Operating Memory

    A data communications interface that transmits multiple bits of data (usually in 1-byte segments) simultaneously. The DEClaser 2100 plus printer uses a Centronics parallel interface. portrait printing A method of printing characters parallel to the short edge of the paper.
  • Page 237 PostScript language A programming language designed to convey a description of a desired page to a printer. It can describe a page containing any combination of text, graphical shapes, and digitized images. primary corona wire A wire located inside the EP-S cartridge that places an electrical charge on the photosensitive drum, preparing it to accept an image from the laser beam.
  • Page 238 It is a permanent memory and cannot be cleared or changed. serial interface A data communications interface that transmits data sequentially, one bit at a time, at a fixed speed. The DEClaser 2100 plus printer uses an RS232C serial interface. sheet In the context of a laser printer, the physical piece of paper that is printed.
  • Page 239 Index Accessories and supplies, B–1 FEEDER menu, 4–18 Associated documents, xiii Font List, 2–48 CDRH regulations, xvii Glossary, 8–1 Changing and saving values, 4–15 Cleaning the printer, 7–1 discharging pins, 7–13 INITIAL menu, 4–23 to 4–26 internal surfaces, 7–2 INTERFACE menu, 4–26 to 4–30 primary corona wire, 7–7 transfer corona wires, 7–13 COMMAND menu, 4–22...
  • Page 240 Memory (Cont.) Paper (Cont.) nonvolatile random-access, 4–9 loading, 2–10 operating, 4–7 manual feed, 2–15 random-access, 4–10 special considerations, 5–3 read-only, 4–8 specifications, 5–2 Menu Paper handling, 5–10 COMMAND, 4–22 Paper jams, 6–12 COPY, 4–22 paper feed, transfer, and fixing assembly areas, 6–18 FEEDER, 4–18 top and rear paper tray, 6–13 INITIAL, 4–23...
  • Page 241 Safety information, xvi Test Print A, 2–41 CDRH regulations, xvii Test Print B, 2–45 laser, xvii Top cover ozone, xvi closing, 2–6 Service, 8–1 opening, 2–4 Service call messages, 6–8 Transfer corona wire, 7–13 Software error messages, 6–5 Transparencies Software requirements, xi special considerations, 5–8 Specifications specifications, 5–8...

Table of Contents