Page 1
SX-M510 • • This Service Manual contains the additional information “DISASSEMBLY INSTRUCTION” and “TEST MODE” for the model XR-MD510/511(K/EZ). If requiring the other information, see Service Manual of XR-MD510(D,K) / 511(EZ), (S/M Code No. 09-004-422-8R1). u163 S/M Code No. 09-004-422-8S1...
http://www.xiaoyu163.com SERVICE JIG AND TOOLS 3 7 63 1515 0 延長用FFCを使用する事で、CD/MDメカニズムを通電 (下図参照) 修理等が行えます。 1FFC, 8P-1.25 88-908-401-110 2FFC, 8P-1.0 SV-J00-043-010 3FFC, 14P-1.0 SV-J00-044-010 L 13942296513 u163 http://www.xiaoyu163.com...
Page 7
http://www.xiaoyu163.com DISASSEMBLY INSTRUCTION 3 7 63 1515 0 1. Removing the outside appearance parts 1) Remove the six screws (1-4, 2-2) and remove the PANEL SIDE R. 2) Remove the six screws (1-4, 2-2) and remove the PANEL SIDE L. R→L L 13942296513 3) Remove the three screw 1 and lift up the PANEL, TOP ASSY 2.
Page 8
http://www.xiaoyu163.com 5) Remove the 11 screws and remove the CABI, REAR. 3 7 63 1515 0 6) This is the state after the outside appearance parts are removed. L 13942296513 2. Removing the PWB, CD ACJ-4 1) Remove the five screws, pull out the FFC and other parts, then remove the PWB, CD ACJ-4.
Page 9
http://www.xiaoyu163.com 2) Remove the screw 1 and remove the PWB, MAIN ASSY 2 in the direction of the arrow. (The board is hooked. 3 7 63 1515 0 While lifting up the HOOK, remove the board.) 4. Removing the FRONT block 1) Remove the screw 1 securing the CAB, FR ASSY and remove the screw 2 securing the CHAS, MD.
Page 10
http://www.xiaoyu163.com 4) This is the state after the PWB, MAIN ASSY and CABI, FRONT ASSY are 3 7 63 1515 0 removed. 5. Removing the MD block (AZG-4) 1) Remove the four screws and remove the MD block. L 13942296513 6.
Page 11
http://www.xiaoyu163.com SERVICE JIG AND TOOLS 3 7 63 1515 0 Using the FFC for extension enables the CD/MD mechanism to be repaired when the power supply is turned on. (Refer to the below figure.) 1 FFC, 8P-1.25 88-908-401-110 2 FFC, 8P-1.0 SV-J00-043-010 3 FFC, 14P-1.0 SV-J00-044-010...
http://www.xiaoyu163.com Notes during re-assembling 3 7 63 1515 0 When assemble the magical change panel, adjust the phase of the gear. 1. Phase adjustment of the GEAR, OPE 1 and GEAR, WORM WHEEL. 1) Align holes 1. 2) Then, move the position of the holes of each gear as shown by 2 in the illustration. L 13942296513 2.
http://www.xiaoyu163.com CD TEST MODE 3 7 63 1515 0 CDテストモードを起動させる。 「CD」 釦を押しながら AC プラグをコンセントに差し込みます。CD テストモードが起動するとディスプレイが全灯 になります。 CDテストモードの解除方法 「POWER」 釦、もしくは CD 以外のファンクション釦を押すか、コンセントからプラグを抜くことで CD テストモー ドを解除することが出来ます。 テストモード機能説明 モード 操作方法 ディスプレイ表示 機能、動作 確認項目 スタートモード CD キー +AC 全灯表示 ・CD TEST MODE スタート ・ディスプレイ点灯確認 プラグ...
Page 15
http://www.xiaoyu163.com CD TEST MODE 3 7 63 1515 0 Starting Up the CD Test Mode While pressing the “CD” button, connect the AC plug to the power outlet. When the CD test mode starts up, all displays turn on. How to Release the CD Test Mode To release the CD test mode, press the “POWER”...
http://www.xiaoyu163.com MD TEST MODE 1. Starting up the MD Test Mode 3 7 63 1515 0 While pressing the MD function button, insert the AC plug into the outlet. Notes: 1) Mechanical abnormalities are ignored while the test mode is starting up. If any abnormality occurs, disconnect the plug immediately.
Page 22
http://www.xiaoyu163.com 9. About Indication 3 7 63 1515 0 The state of circuit, selected disk or switch can be checked on the display. Function Indication pict indication When pict lights When pict glights off Laser power LA READ-1/2-WRITET T-BASS Displayed using the three-step level meter Disk type SELECT GRV TIME MARK...
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT<MD> 3 7 63 1515 0 All the MD blocks are adjusted and checked in the test mode. If “No Adjust” is displayed, perform the adjustments of 1 to 3. 1. Temperature Compensation Adjustment Normally, do not perform the temperature compensation adjustment. If the adjustment value is extensively different, perform the adjustment as given below in a suitable environment for measuring the correct temperature near the unit.
Page 24
http://www.xiaoyu163.com Press the DISPLAY once again. 3 7 63 1515 0 Confirm that the values of “Gf**t##s33” are within the range shown below. (hexadecimal) f “**” ...... 20 to 40 t “##” ...... 15 to 35 s “33” ....15 to 35 FOCUS GAIN TRACKING GAIN SLED GAIN After adjustment, press the STOP button to return the display to “ALL SV OFF”.
Page 25
http://www.xiaoyu163.com 6. UTCO (User TOC) Deleting Procedure 3 7 63 1515 0 If “UTCO ERROR” or other message is displayed when inserting recorded disk and the UTCO needs to be deleted, follow this procedure. Insert the disk whose UTOC is to be deleted. Use the B.SKIP button and F.SKIP button to move the pickup to the center of the disk.
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9301978 0251431 Printed in Singapore http://www.xiaoyu163.com...