Related Manuals for DeLOCK RS-422/485
Summary of Contents for DeLOCK RS-422/485
-
Page 1: Installation Guide
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card Installation Guide DOC#PM-5902x-A0... -
Page 2: Table Of Contents
3.2.2 JP1: RS-422/485 Mode Selector......... 7 3.2.3 S1,S2 Terminal Block Connectors Pin Assignments 8 3.2.4 S1,S2 Terminator Settings ..........8 Installing the RS-422/485 PCI Card ....10 Installing Drivers..........11 5.1 Windows 98, ME, 2000, XP, 2003........11 5.2 Windows NT 4.0 ..............11 Set RS-485 in 2-wire (Half Duplex) Mode.. - Page 3 RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card 6.2 Windows 98, ME ..............14 Set High Baud Rate..........15 7.1 Windows 2000, XP...............15 7.2 Windows 98/ME ..............16 Application Wiring..........17 8.1 RS-485 (Transmitter is controlled automatically by ATTA Hardware)...................17...
-
Page 4: Introduction
Congratulation on your purchasing this high performance 4-wire twisted pair cable RS-422/485 multiport serial PCI card. The card is high speed PCI bus based and plug-and-play compliant. It works at 2-wire (with Auto Transceiver Turn Around feature, ATTA ) and 4-wire configuration. -
Page 5: Package Check List
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card Application Wiring Package Check List Before installing the RS-422/485 multiport serial PCI card to your RS-485 (Transmitter is controlled computer, please make sure the following accessories are well automatically by ATTA Hardware) packed in the box：... -
Page 6: Board Layouts And Connectors
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card Windows 98/ME Board Layouts and Connectors Set the JP5 to “HI” In the Windows COM port properties as the following figure, 2S with DB9 Male Connectors select 〝 Data rate 〞 and click on 〝 Automatic Crystal Detection 〞... -
Page 7: Jp1: Rs-422/485 Mode Selector
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card 3.1.2 JP1: RS-422/485 Mode Selector Set High Baud Rate The RS-422/485 card was shipped at the low baud rate (115.2Kbps maximum). To set to high baud rate to 921.6Kbps AUTO ECHO... -
Page 8: S1,S2 Connector Pin Assignments
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card S1 and S2 have its own setting. You need to go to each Windows 98, ME port to turn on both settings. In this examples, if the first port is COM5 and the second port is COM6, go to the COM5’s “properties”... -
Page 9: With Terminal Block Connectors
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card OUT : Jumper Not Installed Windows 2000, XP Go the the COM3’s properties and set the mode to S2 Terminator Settings (JP8): “RS422/485” Jumper Name Jumper Settings Termination Resistor Setting TXD Terminator Enabled Choose RS485 buffer enable to “Active High”... -
Page 10: Jp5: Uart Input Clock Speed Selector
RS-422/485 Multiport Serial PCI Card RS-422/485 Multiport Serial PCI Card 3.2.1 JP5: UART Input Clock Speed Selector Set RS-485 in 2-wire (Half Duplex) Mode UART Input Clock Speed = 1.8432MHZ, the maximum baud rate is 115.2Kbps To enable your card to work in the RS-485 2-wire mode, please... -
Page 11: S1,S2 Terminal Block Connectors Pin Assignments
Transmitting data will be echoed back Installing Drivers NO_ECHO No echo data (Default) The RS-422/485 PCI card is plug-and-play so the driver LOOP/NO_LOOP LOOP RTS will be connected to CTS installation is quite straightforward. Please “Browse” to the NO_LOOP RTS and CTS operate normally... - Page 12 IN : Jumper Installed chassis. OUT : Jumper Not Installed Plug the RS-422/485 PCI card to the unused PCI expansion slot and attached the I/O card bracket to the computer chassis screw. S2 Terminator Settings (JP8): Jumper Name Jumper Settings Termination Resistor Setting If your card’s connectors are terminal blocks, please install...