Related Manuals for Fisher & Paykel WB60S Series
Summary of Contents for Fisher & Paykel WB60S Series
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS Warming Drawer WB60S models NZ AU GB IE 590513C 04.13... -
Page 2: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! Electrical shock hazard Cut hazard Before carrying out any work on the Take care - some panel edges are sharp. electrical section of the appliance, it must be disconnected from the mains Failure to use caution could result in electricity supply. - Page 3 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! When installing companion products the weight of the companion product should be distributed across the edges of the warming drawer. Products The electrical outlet should be easily accessible above which rest on “feet” may only be installed after installation.
-
Page 4: Parts Supplied
PARTS SUPPLIED Screws (4) Anti-tip bracket (1) Oven support brackets (2) PRIOR TO INSTALLATION the cavity is square and level, and of the required dimensions. the installation will comply with all clearance requirements and applicable standards and regulations. the power switch will be easily accessible to the customer when the warming drawer is installed. the warming drawer (and any product on top of it) will rest on a surface that can support its weight. -
Page 5: Product Dimensions
PRODUCT DIMENSIONS FRONT SIDE Product dimensions (mm) overall height of product overall width of product overall depth of product (including terminal block, excluding handle) depth of chassis (including terminal block) width of chassis height of chassis depth of drawer front panel (excluding handle) depth of drawer when fully open ( measured from front of drawer front panel) -
Page 6: Cabinetry Dimensions
THE FOLLOWING PAGES DETAIL COMMON CABINETRY SCENARIOS CABINETRY DIMENSIONS Underbench (ie installed with a F&P 60cm wide single oven) Oven support Oven Oven brackets 720 mm Warming Drawer Warming Drawer Fit the supplied oven support brackets SIDE Unscrew-fit- rescrew Cabinetry dimensions (mm) Oven support bracket minimum inside height of cavity... - Page 7 CABINETRY DIMENSIONS Wall Mounted (ie installed with a F&P Compact Oven) Compact Oven Warming Drawer Compact Oven 600 mm SIDE Warming Drawer Compact oven Lower grill kit (optional, supplied separately) Warming Drawer Important! Additional 18 mm Wood Spacer In a wall mounted installation, there needs to be an 18 mm Spacer fixed underneath the warming drawer first Cabinet below...
- Page 8 CABINETRY DIMENSIONS Important! If installing under the F&P Coffee Maker, ensure there Wall Mounted (ie installed with a F&P Coffee Maker) is the 45 mm gap at the back of the cabinet and the 200 mm toekick cutout required for airflow. Refer to the Coffee Maker Install instructions.
- Page 9 CABINETRY DIMENSIONS Wall Mounted (Standalone) Supplied Anti-tip Bracket (screwed to the back wall) Important! In a standalone wall mounted installation, you must ensure that the supplied anti-tip bracket is installed unless there is a fixed shelf above acting as an anti-tip obstacle. Fixed shelf Steam Oven Warming Drawer...
- Page 10 DISCARD PACKAGING RESPONSIBLY CONNECT THE WARMING DRAWER TO THE MAINS SUPPLY Important! Unpack the warming drawer and inspect for any signs of damage. Do not install the warming drawer if it has been damaged. All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and local safety regulations.
- Page 11 SECURE THE WARMING DRAWER TO THE CABINETRY Slide the warming drawer fully into the cavity. Ensure it is level. Important! Do not lift the warming drawer by the drawer handle. Fully open the drawer (if the drawer has not already been removed). Fasten the warming drawer in place with the two screws supplied, through the front trim, beneath the drawer.
-
Page 12: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Installer’ s name: Make sure the warming drawer is level and securely fitted to the cabinetry. Installer’ s signature: Make sure any internal packaging has been removed from the drawer. Installation company: Make sure that the isolating switch is accessible by the customer.