Page 2
Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
“Keycard battery low” appears on the child (or a pet) unsupervised, even instrument panel (refer to the informa- for a short while. tion on the “RENAULT card: battery” in They may pose a risk to themselves section 5). or to others by starting the engine,...
Page 9
Replacement: need for an Using the key additional RENAULT Card Refer to the information on “Locking/ If you lose your RENAULT card or unlocking the doors”. require another, you can obtain one Once you have accessed the vehicle from an approved dealer.
If a door or the luggage compartment is open RENAULT card not detected or not properly shut, or if a RENAULT alarm card is still in the reader, the doors and If you open a door while the engine...
RENAULT “HANDS-FREE” CARD: use (1/3) Unlocking the vehicle On equipped vehicles, in addition to RENAULT card in area 1, press the 3 the functions of the above-mentioned button: the vehicle will unlock. remote control RENAULT card, it can In some cases (leaving the vehicle...
If a door or the boot is open or not closed properly, the vehicle will quickly lock/unlock. Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.
Page 13
After locking/unlocking the vehicle or the luggage compartment only using the buttons on the RENAULT card, remote locking and unlocking in hands-free mode are deactivated. To reactivate the “hands-free” mode: restart the vehicle.
Page 14
RENAULT CARD: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. If the vehicle is equipped with a dead- To activate deadlocking...
Page 15
They stop as soon as the driver’s door is opened. With the RENAULT card in the detec- is opened. tion zone, press the button 2 or, de- pending on the vehicle, put your hand round the handle 1, then grip it and pull towards you.
OPENING AND CLOSING THE DOORS (2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Child safety or to others by starting the engine, To make it impossible for the rear doors...
“RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used;...
Page 18
When you lock the doors, the indicator Unlocking the vehicle from the outside light remains lit and then goes out. is only possible with the RENAULT card in the vehicle's access zone or using the key integrated in the RENAULT Interior locking/unlocking card.
AUTOMATIC LOCKING WHEN DRIVING Operating faults You can decide whether you want to activate this function. If you experience an operating fault (no automatic locking, the indicator light in- Operating principle corporated in button 1 does not light up when trying to lock the doors and tail- After the vehicle is started, the system gate, etc.), firstly check that the doors automatically locks the doors when...
FRONT HEADRESTS To adjust the angle of the headrest Depending on the vehicle, tilt section A towards or away from you to the re- quired position. To remove the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary).
REAR HEADRESTS Position for use To refit the headrest Raise or lower the headrest while pull- Insert the headrest rods into the ing it towards the front of the vehicle. sleeves, and lower the headrest to the first notch. To remove the headrest Storage position Press tabs A of rods 1 and 2 simultane- ously and remove the headrest.
FRONT SEATS WITH MANUAL CONTROL (1/2) To tilt the seatback Turn control knob 3 to the required po- sition. Heated seats (depending on vehicle) With the engine running, turn control 4 to either position I, II or III (depending on the temperature required). The message "Heated seat activated»...
Page 23
FRONT SEATS WITH MANUAL CONTROL (2/2) To adjust the lumbar support Table function When the front seat is in on the driver’s seat table position, the front pas- Depending on the vehicle, the passen- senger air bag must be di- ger seatback may be folded down onto Lower handle 5 to increase the support the seat base to create a table.
FRONT SEATS WITH ELECTRIC CONTROL Switch 3 is used for adjusting the seat- back and switch 4 is used for adjusting the seat squab. On equipped vehicles, buttons 1 are used to store the chosen driving posi- tion (refer to the following page). Adjusting the seat squab: –...
Page 25
– with the “hands-free” card de- adjustment buttons is pressed during tected or, depending on the vehicle, recall. RENAULT card in the card reader; When driving, it is not possible to – when the driver’s door is opened. recall a driving position.
Page 26
ACCESS TO REAR SEATS, THREE-DOOR VERSION Locking the seats When a person, an object or a child seat prevents the front seats from lock- ing, perform the following operations: – ask all of the passengers to leave the vehicle and remove any bulky objects from the rear seats;...
SEAT BELTS (1/3) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 28
SEAT BELTS (2/3) Front seat belt reminder ß warning light This lights up on the central display when the engine is started then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes.
Page 29
SEAT BELTS (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special op- erations (e.g. fitting child seats), contact an authorised dealer. –...
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at Depending on the vehicle, the pres- an acceptable level.
Page 32
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation Special feature of the front air This system is only operational when the ignition is switched on. After a violent impact, it has two deploy- ment volumes and integrates a ventila- In a severe frontal impact, the air bags tion system: inflate rapidly, cushioning the impact...
Page 33
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 34
METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 35
SIDE PROTECTION DEVICES Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows...
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 38
CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 39
CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
CHILD SAFETY: choosing a child seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Do not use the child seat seats: via the seat belt or using the system if it may unfasten the seat ISOFIX system.
Page 41
CHILD SAFETY: choosing a child seat mounting (2/2) The ISOFIX anchorage points have been exclu- sively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these anchorage points. Check that nothing is obstructing the anchorage points.
CHILD SAFETY: fitting a child seat (1/12) Some seats are not suitable for fitting In the front seat In all situations, reinsert the headrest to child seats. The diagram on the follow- its full extent so that it does not interfere The laws concerning children travel- ing page shows you how to attach a with the child seat (see the information...
Page 43
CHILD SAFETY: fitting a child seat (2/12) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with their feet nearest the door. Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without al-...
Page 44
CHILD SAFETY: fitting a child seat (3/12) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Type of child seat Seat size Weight of Passenger front Rear centre Rear side seats three and five door...
Page 45
CHILD SAFETY: fitting a child seat (4/12) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal”...
Page 46
CHILD SAFETY: fitting a child seat (5/12) Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 47
CHILD SAFETY: fitting a child seat (6/12) Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 48
CHILD SAFETY: fitting a child seat (7/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Type of child seat Seat size Weight of Passenger front Rear side seats five door version the child...
Page 49
CHILD SAFETY: fitting a child seat (8/12) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal”...
Page 50
CHILD SAFETY: fitting a child seat (9/12) Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 51
CHILD SAFETY: fitting a child seat (10/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Type of child seat Seat size Weight of Front passenger Rear centre Rear side seats the child...
Page 52
CHILD SAFETY: fitting a child seat (11/12) Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 53
CHILD SAFETY: fitting a child seat (12/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Type of child seat Seat size Weight of Front passenger Rear side seats the child seat (1) (5)
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front To deactivate the airbags : when the vehicle is stationary, push and turn passenger airbags lock 1 to the OFF position. (on equipped vehicles) With the ignition on, you must check You must deactivate certain devices ¹...
Page 55
CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels B or C at A on each side of the passenger sun visor 3 (example: label shown above) remind you of these ins- tructions. DANGER Since operation of the front passenger airbag is not...
Page 56
CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a restraint system for a rear-fac- ing child in a seat protected by an ACTIVATED front AIRBAG.
STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering Operating faults The steering may become stiff when Variable power-assisted steering driving or when the steering wheel is The variable power-assisted steering turned repeatedly. This is due to the system is equipped with an electronic power assistance overheating.
Page 59
19 Gear lever. radio information, navigation 2 Side window demister outlet. 20 Engine start/stop button and system information, etc. RENAULT card reader. 3 Stalk for: – Driver and front passenger seat 21 Central door locking/unlocking con- – direction indicator lights;...
Page 61
21 Accessories socket. – direction indicator lights; – activation/deactivation of the trac- 22 Engine start/stop control and card tion control; reader RENAULT. – exterior lights; – activation/deactivation of the 23 Location for radio, navigation – front fog lights; function Stop and Start.
Page 62
WARNING LIGHTS (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Side light tell-tale light Automatic main beam headlight indicator light Please refer to the information Main beam headlight tell-tale á on “External signals and lights” in light Section 1.
Page 64
WARNING LIGHTS (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Oil pressure warning light Engine coolant temperature À Ô warning light If it comes on on the road, ac- This lights up when the ignition is ®...
Page 65
WARNING LIGHTS (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Front seat belt reminder Low fuel level warning light Tyre pressure monitoring ß warning light This lights up when the igni- system This lights up on the central display tion is switched on and goes out after Refer to the information on the “Tyre when starting the engine then, if the dri-...
Page 66
DISPLAYS AND INDICATORS (1/2) Fuel level gauge 5 If the minimum level is reached, in- dicator light 6 comes on and a beep sounds. Fill up as soon as possible. There is only approximately 30 miles (50 km) worth of fuel left after the warn- ing light first comes on.
Page 67
DISPLAYS AND INDICATORS (2/2) Speedometer 7 (mph or km/h) Instrument panel in miles (option to switch to km/h) Overspeed buzzer – With the ignition off, press one of the Depending on the vehicle and coun- buttons 9 or 10 at the end of stalk 2 try, a buzzer sounds for approximately and start button 8;...
TRIP COMPUTER: general information (1/2) c) mileage before service; d) tyre pressure reset; e) vehicle settings customisation menu; f) trip log, operating faults and informa- tion message readout. Trip computer and warning Display selection keys 2 system 1 and 3 Depending on the vehicle, this includes Scroll through the following informa- the following functions:...
Page 69
TRIP COMPUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
Page 70
ON-BOARD COMPUTER: trip settings (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101668 KM a) Total mileage and trip mileage recorder. 112. 4 KM Fuel used Fuel used b) Journey parameters.
Page 71
ON-BOARD COMPUTER: trip settings (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Current Current Current fuel consumption. 7.4 L/100 This value is displayed above a speed of approximately 7.4 L/100 18 mph (30 km/h).
Page 72
ON-BOARD COMPUTER: trip settings (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message c) Mileage before service or oil change. Mileage before service Service in SERVICE With the ignition switched on, and the engine not running...
Page 73
ON-BOARD COMPUTER: trip settings (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) c) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on and the engine not running,...
Page 74
ON-BOARD COMPUTER: trip settings (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected FRONT TYRES d) Tyre pressure monitor Refer to the information on the “Tyre pressure monitor” in Section 2.
Page 75
ON-BOARD COMPUTER: trip settings (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected e) Vehicle settings customisation menu. Settings menu: Enables certain vehicle functions to be set (instrument panel language, parking press and hold distance control, etc.).
Page 76
«Please remove Request to remove the RENAULT card from the reader when you leave the vehicle. keycard» «Checking control Displayed with the ignition on when the vehicle is running self-diagnostics.
Page 78
TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.
VEHICLE SETTINGS CUSTOMISATION MENU i) Parking sensor volume; j) Language. function activated < function deactivated Once a line has been selected, keep pressing button 2 or 3 to change the function. If you select either “Parking sensor volume” or “Language”, you will have to make a further selection (sound volume of the parking distance control or instrument panel language).
CLOCK AND EXTERIOR TEMPERATURE Vehicles equipped with a External temperature navigation system, radio, etc. indicator For vehicles which are not fitted with Special note: buttons 2 and 3, refer to the specific When the external temperature is be- equipment instructions to discover the tween –3°C and +3°C, the °C charac- special features.
REAR VIEW MIRRORS Folding door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position B). In this case, they will fold out when the ignition is next switched In any case, you can make the door mirrors fold in (switch 2 in position C) or fold out (switch 2 in position A).
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
EXTERIOR LIGHTING AND SIGNALS (1/4) Daytime running lights function Depending on the vehicle, the daytime running lights come on automatically when the engine is started. Main beam headlights á With the dipped beam head- lights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on.
Page 84
EXTERIOR LIGHTING AND SIGNALS (2/4) Automatic main beam Activation headlights Turn ring 2 until the AUTO symbol is op- posite mark 3. Depending on the vehicle, this system Pull stalk 1 to activate main beam switches the main beam headlights on headlights.
Page 85
EXTERIOR LIGHTING AND SIGNALS (3/4) “See-me-home lighting” Special note: – If the dipped beam headlights are function manually switched on and if the light This function allows you to briefly switch is sufficient, the directional head- on the dipped beam headlights (to pro- lights will remain fixed;...
EXTERIOR LIGHTING AND SIGNALS (4/4) Front fog lights Switching off the lights Turn centre ring 5 on stalk 1 Turn ring 5 again until mark 6 is oppo- until the symbol faces mark 6, then re- site the symbol for the fog light that you lease it.
Page 87
ADJUSTING THE HEADLIGHT BEAM HEIGHT Examples of positions for adjusting control A according to the load Five door Three door Driver alone or with front passenger Driver with one front passenger and one rear passenger On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
WINDSCREEN WASH/WIPE (1/5) Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Vehicle fitted with intermittent Special note water; windscreen wipers When driving the vehicle, the wiping –...
Page 89
WINDSCREEN WASH/WIPE (2/5) Note: – the rain sensor is only intended as a driving aid. In the event of re- duced visibility, the driver should manually activate the wipers. In foggy weather or during snow- falls, wiping is not automatically triggered and remains under the driver’s control;...
Page 90
WINDSCREEN WASH/WIPE (3/5) Operating fault Special note In the event of a malfunction of the When driving the vehicle, the wiping automatic wiping, the wiper is set to speed slows down whenever the vehi- intermittent wiping. Contact an au- cle stops. For example, fast wiping thorised dealer.
WINDSCREEN WASH/WIPE (4/5) Specific front wiper position Note: (service position) Once the wipers have been switched off, at least 1 minute after locking the This position enables the blades to be vehicle, it is possible to manually move lifted to remove them from the winds- the blades.
WINDSCREEN WASH/WIPE (5/5) Headlight washers Headlights on In the event of obstacles present On equipped vehicles, hold stalk 1 on the windscreen (dirt, snow, ice, pulled towards you for about 1 second, etc.), clean the windscreen (inclu- and the headlight washers and winds- ding the central area located behind creen washers will be activated at the the interior rear-view mirror) and...
REAR SCREEN WASH/WIPE Rear screen washer/ wiper With the ignition on, push the stalk. Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Rear screen wiper water;...
FUEL TANK (1/3) Fuel grade Vehicles running on ethanol-based fuel Use a high-grade fuel that complies with the legislation in force in each It is essential to use unleaded petrol or country and which must conform to the fuel containing a maximum of 85% eth- specifications given on the label on the anol (E85).
FUEL TANK (2/3) Filling with fuel With the ignition off, insert the nozzle to open valve A and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation.
Page 96
(3/3) Running out of fuel on diesel Vehicles without priming bulb 2 versions Insert the RENAULT card into the 3 card reader. Press the start button 1 Vehicles with priming bulb 2 without pressing any of the pedals. Wait After a breakdown caused by com- a few minutes before starting.
Page 97
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting, stopping the engine .
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm.
2 or in detection zone 3. When you get into the vehicle, insert the clutch pedal until the engine starts. RENAULT card fully into card reader 2. To start, depress the brake or clutch pedal and press button 1. If a gear To start, press button 1.
Page 100
In certain cases, the hands-free RENAULT card, insert the card into RENAULT card may not work: reader 2; – when the RENAULT card battery is – vehicles with a RENAULT “hands- drained, flat battery, etc. free” card, with the card in the pas- –...
Page 101
When you leave your vehi- the message “No keycard Press and cle, especially if you have hold” will appear on the instrument your RENAULT card with panel: press the button 1 for longer you, check that the engine than two seconds.
Page 102
FUNCTION STOP AND START (1/3) Preventing the engine from Conditions for coming out of This system enables a reduced fuel consumption and lower greenhouse standing by engine standby gas emissions. The system is activated In certain situations, such as negotiat- For vehicles equipped with manual automatically when the vehicle is star- ing a crossroads for instance, it is pos-...
Page 103
FUNCTION STOP AND START (2/3) Conditions preventing the Special cases – the engine temperature is too low; standby of the engine – the anti-pollution system is required; With the engine on standby (traffic jam, traffic lights, etc.), if the driver unfastens Certain conditions prevent the system –...
Page 104
FUNCTION STOP AND START (3/3) Special feature of the automatic The system reactivates automati- engine re-start cally each time the vehicle is started using the start button (please refer Under certain conditions, the engine to “Starting, stopping the engine” in can restart on its own in order to gua- Section 2).
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
GEAR LEVER/HANDBRAKE Handbrake To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: Pull the lever 2 upwards and make sure the vehicle is immobilised. Make sure that the hand- brake is properly released Selecting reverse gear when driving (red indicator...
ELECTRONIC PARKING BRAKE (1/3) Note: To indicate that the electronic parking brake is released, a beep sounds and the message “Apply parking brake” ap- pears on the instrument panel: – with the engine running: when the driver’s door is opened; –...
3 at the same time; Applying the electronic parking running, etc.): pull and release switch 3. brake – remove the RENAULT card from the The brake is released as soon as the Pull switch 3. Indicator lights 2 and vehicle is started up again.
DRIVING ADVICE, ECO-DRIVING (1/3) Journey record Fuel consumption is accredited in ac- cordance with a standard regulatory Once the engine is switched off, you method. Identical for all manufactur- will see “Journey record” displayed on ers, this enables vehicles to be com- the screen 1, enabling you to view in- pared with one another.
Page 112
DRIVING ADVICE, ECO-DRIVING (2/3) An overall rating from 0 to 100 is dis- – Avoid sudden acceleration. played to let you assess your eco driv- – Brake as little as possible. If you an- ing performance. The higher the score, ticipate an obstacle or bend in ad- the better your eco-driving perform- vance, you may then simply release...
Page 113
DRIVING ADVICE, ECO-DRIVING (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
MAINTENANCE AND ANTI-POLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that fail- end of their service life, which will come ure to respect anti-pollution regulations The exhaust gas monitoring system will into force in 2015.
This commitment is illustrated by the lation. less fuel (eg. 140 g/km, equivalent to Renault eco² signature. 5.3 l/100 km for a diesel vehicle). Recycling Our vehicles are also equipped with a Manufacture...
TYRE PRESSURE MONITORING SYSTEM (1/4) If the vehicle is equipped with the func- It should always be done after checking tion, this system monitors the tyre pres- the tyre pressure of all four tyres when sure. cold. Tyre pressures must correspond to the current usage of the vehicle (empty, Operating principle carrying a load, motorway driving, etc.).
Page 117
TYRE PRESSURE MONITORING SYSTEM (2/4) “Puncture” The wheel A, together with the warn- ing light 4 , indicates that the af- fected wheel is punctured or severely underinflated. Replace it or contact an authorised dealer if it is punctured. Top up the tyre pressure if the wheel is de- flated.
Page 119
TYRE PRESSURE MONITORING SYSTEM (4/4) Readjustment of tyre pressures The tyre pressures must be adjusted when cold (please refer to the label lo- cated on the edge of the driver’s door). If tyre pressures cannot be checked when the tyres are cold, the recom- mended pressures must be increased by 0.2 to 0.3 bar (3 PSI).
DRIVER CORRECTION DEVICES AND AIDS (2/4) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced under- ing fault the message “Check ESC”...
DRIVER CORRECTION DEVICES AND AIDS (3/4) The traction control system offers ad- Hazard warning lights switching on ditional safety. It is recommended that Depending on the vehicle, these may you do not drive with the function di- light up in the event of sudden decel- sabled.
Page 123
DRIVER CORRECTION DEVICES AND AIDS (4/4) Hill start assistance The hill start assistance This device assists the driver when system cannot completely starting on hills (ascending or descend- prevent the vehicle from ing). It prevents the vehicle from rolling rolling backwards in all sit- forwards or backwards by automatically uations (extremely steep gradients, applying the brakes when the driver lifts...
LANE DEPARTURE WARNING (1/2) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
Page 125
LANE DEPARTURE WARNING (2/2) Adjustment The function sounds the alarm if: a line is crossed without activating the From the vehicle settings customisation indicator lights. The function alerts the menu (please refer to the information on the “Vehicle settings customisation driver through a warning light menu”...
Page 126
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you Controls Switching on stay within the driving speed limit that Press the side switch 1 . Warning 1 Main “On/Off” switch. you choose, known as the limit speed. light 7 comes on, lit orange, and the 2 Limit speed activation, storage and message “Speed limiter”...
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any moment. To do this: press the accelerator pedal firmly and fully –...
Page 128
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Putting the function on Recalling the limit speed Switching off the function standby If a speed has been stored, it can be re- The speed limiter function is deacti- called by pressing switch 5 (R). vated if you press switch 1: in this case The speed limiter function is deacti- a speed is no longer stored.
Page 129
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. The cruise control function helps you to Controls Therefore, it can under no circum- maintain your driving speed at a speed stances replace the driver’s respon- that you choose, called the cruising...
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving At a steady speed (above 20 mph Once a cruising speed is stored and Press switch 1 on the side showing (30 km/h) approximately) press the cruise control function is active, Warning light 7 comes on, lit green, and switch 2 (+): the speed is stored.
Page 131
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed Putting the function on standby The cruising speed may be exceeded at any time by depressing the acceler- The function is suspended when you: ator pedal. The cruising speed flashes –...
Page 132
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed Note: if the speed previously stored is Switching off the function If a speed is stored, it can be recalled, much higher than the current speed, The cruise control function is deacti- once you are sure that the road condi- the vehicle will accelerate more rapidly vated if you press switch 1: in this case...
PARKING DISTANCE CONTROL (1/4) Rear parking distance control Operation When reverse gear is selected, most objects which are less than approxi- mately 1.20 metres from the rear of the vehicle are detected and a beep sounds. This function is an addi- tional aid that indicates the distance between the vehi- cle and an obstacle whilst...
Page 134
PARKING DISTANCE CONTROL (2/4) Front parking distance control (depending on vehicle) Operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h). Most objects located less than around 1 metre away from the front of the ve- hicle are detected and a beep sounds.
PARKING DISTANCE CONTROL (3/4) Prolonged deactivation of the Special features Ensure that the ultrasonic sensors are system not obscured (by dirt, mud, snow, etc.). You may permanently activate or deac- tivate the front or rear parking distance control separately. From the customisation menu Select line “Front parking sensor”...
Page 136
PARKING DISTANCE CONTROL (4/4) Operating faults When the system detects an operating fault, a beep sounds for approximately 3 seconds each time reverse gear is se- Park Assist lected and is accompanied by the mes- Rear parking sensor sage “Check parking sensor” shown on Volume the instrument panel.
REVERSING CAMERA (1/2) Operation 3 moving guide line: This gauge remains fixed and indicates the vehicle trajectory if the wheels are This is shown in blue on screen 2. It in- Moving into reverse gear, the camera 1 in line with the vehicle. dicates the vehicle trajectory according located near the number plate lights to the position of the steering wheel.
Page 138
REVERSING CAMERA (2/2) Park Assist The screen shows a reverse image. Rear parking sensor The frames are a representation projected onto flat ground; this in- Volume formation must not be taken into Rear camera view settings account when superimposed on a Image settings vertical object or an object on the ground.
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Select position D. In most traffic con- ditions, you will not have to touch the gear selector lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particu-...
AUTOMATIC TRANSMISSION (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – If the road contours and bends When the vehicle is stopped, move the move the lever to the left. Shifting the do not allow you to stay in auto- lever to position P while keeping your lever repeatedly allows you to change...
Page 141
AUTOMATIC TRANSMISSION (3/3) Operating faults – When driving, if the “Check auto gearbox” message appears on the instrument panel, it indicates a fault. Contact your approved Dealer as soon as possible. – When driving, if the message “Auto gearbox overheating” appears on the instrument panel, stop the ve- hicle to allow the gearbox to cool down.
AIR VENTS: air outlets (1/2) Depending on the vehicle: 1 left-hand side air vent 2 left-hand side window demister outlet 7 passenger footwell heater outlets 3 windscreen demister outlets 8 centre console air vents 4 centre air vents 9 air conditioning control panel 5 right-hand side air vent 6 right-hand side window demister outlet...
AIR VENTS: air outlets (2/2) Air flow Direction To remove bad odours from your ve- hicles, only use the systems designed Turn control knob 1 (beyond the point Right/left: move tabs 2 to the right or for this purpose. Consult an approved of resistance).
MANUAL AIR CONDITIONING (1/2) Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the...
MANUAL AIR CONDITIONING (2/2) “OFF" position: the system is deactivated: the ventila- tion speed for the passenger compart- ment air is zero (vehicle stationary), you can however still feel a slight flow of air when the vehicle is moving. Recommended demisting option: Turn controls 1, 2 and 4 to the position.
AUTOMATIC CLIMATE CONTROL (1/5) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), whilst optimising consumption. The system controls the ventilation speed, air distribution, air recircula- tion, and starting and stopping the air conditioning and air temperature.
Page 149
AUTOMATIC CLIMATE CONTROL (2/5) Clear View function Press button 10: the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de- icing functions must be activated.
Page 150
AUTOMATIC CLIMATE CONTROL (3/5) The displayed temperature values show a comfort level. When starting the engine, in- creasing or decreasing the value displayed will not allow the com- fort level to be reached any more quickly. The system will always op- timise the temperature increase or decrease (the ventilation system does not start instantly at maximum...
Page 151
AUTOMATIC CLIMATE CONTROL (4/5) The air flow is directed to the Ø windscreen and the front side window demisting vents. The air flow is distributed be- × tween front side window de- misting vents, the windscreen demist- ing vents and the footwells. The air flow is directed mainly ¿...
Page 152
AUTOMATIC CLIMATE CONTROL (5/5) Recycling This function is managed automati- cally (operation is confirmed by warn- ing light 14 on display 12), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
AIR CONDITIONING: information and advice on use Advice on use In some situations, (air conditioning Operating faults off, air recirculation activated, venti- Fuel consumption lation speed at zero or low, etc.) you As a general rule, contact your ap- You will normally notice an increase may notice that condensation starts proved Dealer in the event of an op- in fuel consumption (especially...
Never leave your vehicle with the Electric windows From the driver’s seat, use switch: RENAULT card inside and never 1 for the driver’s side; leave a child (or a pet) unsuper- Press or pull the switch to raise or lower 2 for the front passenger side;...
(some- body’s fingers, etc.) it stops and then moves back several centimetres. Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a Sun blind Sunroof child (or a pet) unsupervised, even –...
Technical Department; RENAULT card twice in quick suc- (the window will close gradually), hold – do not open the sunroof immedi- cession, or on the driver's door in...
MANUAL WINDOW WINDERS / SUN VISOR Manual window winders Sun visor Turn handle 1. Lower the sun visor 2 over the wind- screen or unclip it and turn it over the side window. Courtesy mirrors Slide cover 3, depending on the vehi- cle, and the mirror is lit.
INTERIOR LIGHTING (1/2) Map reading lights (depending on vehicle) Move switches 1 or 3. Courtesy light Front door lights Tilt switch 2 to move it to the position Light 4 comes on when the door is for: opened. – permanent lighting; –...
Page 159
INTERIOR LIGHTING (2/2) Glovebox light 5 Boot light 6 Light 5 comes on when the cover is Depending on the vehicle, the light 6 opened. comes on when the boot is opened. 3.17...
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/4) Door pockets 1 Sun visor storage 2 This can be used for storing motorway tickets, cards, etc. Ensure that no hard, heavy Nothing should be placed or pointed objects are on the floor area in front of placed in the “open”...
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/4) Front centre armrest storage Centre console storage Passenger storage compartment A compartments 5 compartment Press the button 3 and lift the cover 4. Pull the handle 6 to open it. The glove box can hold A4-size docu- ments, a large bottle of water, etc.
Page 162
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/4) Door storage compartment 7 Storage compartment 8 Rear armrest with cup holder Pull down the armrest 9. 3.20...
Page 163
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/4) Clothes hooks 10 Front seat storage pockets 12 Rear centre console storage compartments 13 Grab handle 11 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
ASHTRAY, ACCESSORIES SOCKET Accessories sockets 1 Ashtray 2 They are designed for connecting ac- To open, lift the cover. To empty, pull the cessories with a maximum power rating ashtray towards you and it will be re- of 120 Watts (voltage: 12V) which leased from its housing.
REAR BENCH SEAT functions (1/2) Sport tourer versions To fold down the seatback Press button 1 lower seatback(s) A. Ensure that the front seats are far Depending on the vehicle, seatback A enough forward. can be folded down on its own to allow long or bulky objects to be transported.
Page 166
REAR BENCH SEAT functions (2/2) When moving the rear bench seat, ensure that nothing obstructs the an- chorage points (part of the The seat and the seatback may be body, a pet, gravel, cloth, toys, etc.). folded away to allow bulky objects to be carried.
Page 167
TAILGATE To open Opening manually from inside the vehicle Press button 1 and lift the tailgate. Special note: To close If it is impossible to unlock the tailgate, Pull down the tailgate using handle 2 it can be done from inside. inside the tailgate to assist you.
REAR PARCEL SHELF Removal Lift rear parcel shelf 2 slightly and pull it Unclip mountings 3 on either side of towards you. the parcel shelf, then remove the parcel Unhook the two cords 1 (tailgate side). shelf via the luggage compartment. To refit it, proceed in reverse order to removal.
Page 169
LUGGAGE COMPARTMENT COVER: estate models To remove the flexible Removing the luggage cover section of the luggage cover Push the luggage compartment cover to the left (movement A) and lift the Pull handle 1 gently to release the pins right-hand side of the inertia reel (move- from their mounting points located on ment B).
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (1/3) Storage under carpet 1 Anchorage points Side straps (depending on vehicle) (Three- and five-seater versions) Side straps 3 are located either side of To open, fold back carpet A. Hooks 2 located on each corner of the the luggage compartment, and can be luggage compartment, allow the load to used to store an oil can.
Page 171
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (2/3) Anchorage points Storage under carpet (sport tourer version) (sport tourer version) Hooks 5, located on either side of the To access storage compartments 7, luggage compartment, allow the load to fold back section B using handle 4 and, be secured.
Page 172
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (3/3) Separating the luggage On the back there is an elastic strip 9 to hold small objects vertically in position. compartment (sport tourer version) The loading area can be separated. Turn locks 8 situated on either side of the luggage compartment to the first notch.
Page 173
TRANSPORTING OBJECTS IN THE BOOT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, the mobile floor in the flat-floor position (exam- ple B).
TRANSPORTING OBJECTS towbar Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to Three-door version B = 872 mm the information on “Weights” in Five-door version B = 867 mm Section 6. Estate version B = 1,070 mm Choice and fitting of towing equipment Maximum weight of towing equip-...
TRANSPORTING OBJECTS: luggage net (1/2) Fitting the luggage net behind the front seats Inside the vehicle on each side: – lift cover 1 to access the upper mounting ring of the net; – fix the net belt hook onto the ring; Luggage net A –...
Page 176
TRANSPORTING OBJECTS: luggage net (2/2) – in the luggage compartment, fix the lower mounting strap hook on the net to the anchorage point 4 loca- ted under the luggage compartment carpet; – adjust the net strap so that it is taut. Fitting the luggage net behind the rear bench seat Inside the vehicle on each side:...
ROOF BARS: ACCESS TO FIXING POINTS Three door version The fitting of roof bars is prohibited on Sport tourer versions three door versions. For vehicles fitted with original roof bars, the roof bars are fixed and must not be removed. To change them contact an approved Dealer.
MULTIMEDIA EQUIPMENT Multimedia systems The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Multimedia display; 2 Radio; 3 Central control; 4 Multimedia sockets; 5 Steering column control;...
BONNET (1/2) To open, pull handle 1, located on the Unlocking the bonnet catch left-hand side of the dashboard. To release it, lift tab 2. Opening the bonnet Lift the bonnet; you will need to guide it as it is held by a strut. Before performing any action in the engine com- partment, the ignition must...
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
Page 182
ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Oil level Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) ...
ENGINE OIL LEVEL: general information (2/2) Exceeding the maximum engine oil level The oil level should only be read with the dipstick as explained above. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer. Consult your approved Dealer at once if you notice an abnormal or Reading the level using the...
ENGINE OIL LEVEL: topping up, filling (1/3) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
Page 185
ENGINE OIL LEVEL: topping up, filling (2/3) Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels. In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil.
ENGINE OIL LEVEL: topping up, filling OIL CHANGE (3/3)/ Oil change Engine oil change: if you Service interval: refer are changing the oil when Maintenance Document for your vehi- the engine is hot, be careful cle. not to scald yourself if the oil overflows.
LEVELS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
LEVELS (2/3) Level 2 Topping up It is normal for the level to drop as After any operation on the hydraulic cir- the linings become worn, but it should cuit, a specialist must replace the fluid. never drop below the “MINI” warning Only use fluids approved by our line.
LEVELS /FILTERS (3/3) Filters Liquid Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. Use a tool such as a needle to adjust the height of the windscreen washer Replacement intervals for filter ele- jets.
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure Tyre safety and use of snow chains: monitoring system Refer to the information on “Tyres” in Section 5 for the servicing conditions If under-inflated (puncture, low pres- and, depending on the version, the use of chains.
Page 191
TYRE PRESSURES (2/2) G: tyre pressure for the emergency spare wheel. H: emergency spare wheel tyre dimen- sion if different to the four tyres fitted to the vehicle. For your safety and to comply with the law. When they need to be re- placed, only tyres of the same make, size, type and profile should be used on a single axle.
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the in- strument panel for the duration of the charging time.
Page 193
BATTERY (2/2) Replacing the battery Before performing any As this operation is complex, we advise action in the engine com- you to contact an authorised dealer. partment, the ignition must be switched off by pressing Vehicle fitted with the Stop and Start the engine stop button (please see function the information on “Starting, stop-...
BODYWORK MAINTENANCE (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
Page 195
BODYWORK MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g.: instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle re- temperature display, radio display, mul- gularly.
Page 197
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
PUNCTURE, EMERGENCY SPARE WHEEL In the event of a puncture, Special note: depending on the vehicle, The Tyre Pressure Monitor function you will have: does not check the emergency spare wheel (the wheel replaced by the emer- An emergency spare wheel or tyre in- gency spare wheel disappears from the flation kit (refer to the information on the instrument panel display).
TYRE INFLATION KIT (1/5) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 202
TYRE INFLATION KIT (2/5) Depending on the vehicle, remove the – adjust the pressure: to increase central partition in the storage compart- it, continue inflating with the kit, to ment to access the inflation kit. reduce it, turn button 7 located on the inflation adapter.
Page 203
TYRE INFLATION KIT (3/5) – affix driving recommendation label 9 Precautions when using the kit to the dashboard where it can easily The kit should not be operated for more be seen by the driver; than 15 consecutive minutes. – store the kit; –...
Page 204
TYRE INFLATION KIT (4/5) Engine running, handbrake applied: – after a maximum of 15 minutes, stop inflating and read the pressure (on – unroll the hose from the container; pressure gauge 14). – connect the compressor hose 12 to Note: while the container is empty- the container’s inlet 17;...
Page 205
TYRE INFLATION KIT (5/5) – Affix the driving recommendation Precautions when using the kit label to the dashboard where it can The kit should not be operated for more easily be seen by the driver; than 15 consecutive minutes. – Put the kit away. –...
Page 206
TOOLS Wheel brace 1 Locks or unlocks the wheel bolts and tow eye 6. Jack 2 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned) 3. Hubcap tool 4 This tool is used to remove the wheel Do not leave the tools un- trims.
WHEEL TRIMS - WHEEL Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, Remove the wheel trim using hubcap check that all the tools are correctly tool 1 (located in the tool kit) by en- clipped into the tool kit, then position gaging the hook in the opening near it correctly in its housing: there is a...
CHANGING A WHEEL (1/2) Vehicles equipped with a jack Offer up the jack 4 horizontally; the jack head must be lined up with jacking and wheelbrace point 1 located on the underside of the If necessary, remove the wheel trim. sill, closest to the wheel concerned, as shown by arrow 2.
Page 209
CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
TYRES (2/3) Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure tyres are cold; ignore higher pressures monitoring system Adhere to the tyre pressures (including which may be reached in hot weather If under-inflated (puncture, low pressure the emergency spare wheel).
Page 212
TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- chains to the rear axle is strictly for- sary to observe the speed specified by For safety reasons, this op- bidden.
FRONT HEADLIGHTS: changing bulbs (1/3) After opening the bonnet, pull tool A Dipped beams Do not touch the bulb glass. Hold it upwards. Remove the two screws 1 by its base. from the headlight using the A tool. Halogen dipped beam headlight When the bulb has been changed, Unlock the two springs D, remove make sure you refit the cover correctly.
FRONT HEADLIGHTS: changing bulbs (2/3) Front side light Remove the cover E and pull the bulb holder 6. Bulb type: W5W. Before performing any Discharge bulb dipped beam Daytime running light action in the engine com- headlight partment, the ignition must Remove the cover C, unlock the bulb Bulb type: D1S.
Page 215
FRONT HEADLIGHTS: changing bulbs (3/3) Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. Daytime running lights 7 Please see an authorised dealer. Front fog lights 8 The front bumper needs to be removed; Any operation on (or mo- consult an approved Dealer.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (1/6) Five-door versions – loosen nut 1, press down on it to Direction indicator lights 5 release the front of the light (move- Bulb type: PY21W. Direction indicator lights/brake and ment A) then remove the nut; Side light and brake light 6 side lights –...
Page 217
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (2/6) Five-door versions – Lower the tailgate, then pull light 9 Reversing light 10 towards the rear to release it. (continued) Bulb type: W16W. – Unscrew the bulb holder for the bulb Fog light (left or right-hand side)/ Fog lights/side lights and reversing concerned.
Page 218
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (3/6) Three-door versions 16 Side light/stop light Bulb type: P21/5W. – Unclip the access flap; 17 Direction indicator light – unscrew nuts 12 and 13; Bulb type: PY21W. – from the outside, remove bolt 14, then pull on the light;...
Page 219
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (4/6) Sport tourer Versions Side light 22 Bulb type: W5W. Side lights/reversing lights and fog Reversing light 23 lights Bulb type: P21W. – From the luggage compartment, unclip flap 20 (movement C), then Fog light (left or right-hand side) 24 remove the bolts .
INTERIOR LIGHTING: changing bulbs (1/2) Courtesy light Door lights Glove box light – Position the 3 switches in the central Unclip light 2 (using a flat-blade screw- Open the access cover 3, you can then position; driver or similar). unclip the bulb holder more easily 4. –...
INTERIOR LIGHTING: changing bulbs (2/2) Luggage compartment light Disconnect the light. Press tab 6 to release lens 8 and Unclip the light at 5 using a flat-blade access bulb 7. screwdriver or similar. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced.
FUSES (1/2) Fuse box Tweezers 1 If any electrical component does not Remove the fuse using tweezers 1, lo- work, check the condition of the fuses. cated at the back of flap A or B. Check the fuse in question Unclip cover A or B (depending on ve- To remove the fuse from the tweezers, and replace it, if neces-...
Page 225
FUSES (2/2) Allocation of fuses 8 Interior rear-view mirror; Some accessories are protected by fuses located in the engine compart- (the presence of certain fuses depends 9 Rear screen wiper; ment in fuse box C. on the vehicle equipment level) 10 and 11 Rear electric windows;...
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers The battery charger must be com- (courtesy lights, etc.) are switched patible with a battery with nominal off before disconnecting or recon- voltage of 12 volts.
Page 227
BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
(insert the the next time the vehicle is started, the replace the RENAULT card battery, RENAULT card in the card reader) and message will disappear. press button 1 pulling on emergency lock/unlock the vehicle (refer to the in-...
FITTING A RADIO If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please con- –...
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only.
WINDSCREEN WIPER BLADES Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
If your vehicle is the towing or R for vehicles with automatic trans- vehicle, do not exceed the maximum missions), insert the RENAULT card in towing weight for your vehicle (refer the card reader then press the engine to the information on “Weights” in start button for two seconds.
Unclip cover 5 or 7 by sliding a flat tool (never use the drive shafts or any other (or the key integrated in the RENAULT part of the vehicle). These towing points card) under the cover.
Page 234
Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the in- formation on “Locking, unlocking the open-...
Starting conditions are not ful- Please refer to the information on “Starting, stopping filled. the engine” in Section 2. The RENAULT “hands-free” card Insert the card in the card reader in order to start does not work. the engine. Please refer to the information on “Starting, stopping the engine”...
Page 236
OPERATING FAULTS (3/6) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
Page 237
OPERATING FAULTS (4/6) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
Page 238
OPERATING FAULTS (5/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
Page 239
OPERATING FAULTS (6/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights. Traces of condensation may be a nat- ural phenomenon caused by varia- tions in temperature. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the...
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MAM (Maximum Authorised Mass) hicle identification plate should be 5 GTW (Gross train weight: vehicle quoted on all correspondence or fully loaded, with trailer). orders. 6 MPAW (Maximim Permissible Weight) for front axle. The presence and location of the in- 7 MPAW on rear axle.
ENGINE IDENTIFICATION PLATES (1/2) Quote the information on the identi- fication plate or label A in all corre- spondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 244
ENGINE IDENTIFICATION PLATES (2/2) Quote the information on the identi- fication plate or label A in all corre- spondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
ENGINE SPECIFICATIONS Versions 1.2 TCe 1.6 16V 2.0 16V 2.0 T 1.5 dCi 1.6 dCi 1.9 dCi 2.0 dCi Engine type H5F Turbo F4R Turbo (see engine plate) Cubic capacity (cc) 1 197 1,598 1,998 1,998 1,461 1 598 1,870 1,995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel...
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Five door Estate Three door Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Gross Train Weight (MTR) the information on “Vehicle identification plates”...
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 252
SERVICE SHEETS (2/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 253
SERVICE SHEETS (3/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 254
SERVICE SHEETS (4/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 255
SERVICE SHEETS (5/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 256
SERVICE SHEETS (6/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
ANTICORROSION CHECK (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 258
ANTICORROSION CHECK (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 259
ANTICORROSION CHECK (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 260
ANTICORROSION CHECK (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 261
ANTICORROSION CHECK (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.21...
Page 262
ANTICORROSION CHECK (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.22...
Need help?
Do you have a question about the Megane and is the answer not in the manual?
Questions and answers