Page 1 MEGANE COUPE CABRIOLET DRIVER’S HANDBOOK...
Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
Page 3: Driving
This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
Page 5: Table Of Contents
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 7 RENAULT card: General information, use, deadlocking ........
Page 8: Doors
“Keycard battery low” appears on the inside and never leave a instrument panel (refer to the informa- child (or a pet) unsupervised, even tion on the “RENAULT card: battery” in for a short while. section 5). They may pose a risk to themselves...
Page 9 Replacement: need for an Using the key additional RENAULT Card Please refer to the information under If you lose your RENAULT card or “Locking and unlocking the opening el- require another, you can obtain one ements”. from an approved dealer.
Page 10: Remote Control Card Use
If a door or the luggage compartment is open RENAULT card not detected or not properly shut, or if a RENAULT alarm card is still in the reader, the doors and If you open a door with the engine run-...
Page 11: Unlocking The Vehicle
HANDS-FREE RENAULT CARD: use (1/3) Unlocking the vehicle On equipped vehicles, in addition to With the RENAULT card in the zone 1, the functions of the above-mentioned press the button 3 or, depending on the remote control RENAULT card, it can...
Page 12: Locking The Vehicle
Remote locking passenger compartment (or the card With the RENAULT card on you, and reader) the vehicle will not lock. In this doors and tailgate closed, move away situation, no beep sounds and the from the vehicle: it will lock automati- hazard warning lights do not flash.
Page 13 After locking/unlocking the vehicle or the luggage compartment only using the buttons on the RENAULT card, remote locking and unlocking in hands-free mode are deactivated. To reactivate the “hands-free” mode: restart the vehicle.
Page 14 RENAULT CARD: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. If the vehicle is equipped with a dead- To activate deadlocking...
Page 15: Opening And Closing The Doors
Hands-free RENAULT card ing the window from lowering when one of the doors is opened, this ice With the RENAULT card in the detec- or snow must be removed to free the tion zone, press the button 2 or, de- window before the door is closed.
Page 16 OPENING AND CLOSING THE DOORS (2/3) Lights-on reminder buzzer If you have switched off the ignition and left the lights switched on, a re- minder buzzer will sound when a door is opened. Card reminder buzzer On opening the driver’s door, if the card is still in the reader, the message “Please remove keycard”...
Page 17 OPENING AND CLOSING THE DOORS (3/3) In the event of an operating fault on Door locking is accompa- the electric windows when moving nied by the windows clos- the doors ing. The window does not lower when the Risk of serious injury. door is opened and does not close when the door is closed.
Page 18: Locking/Unlocking Doors
LOCKING/UNLOCKING THE DOORS (1/2) Locking/unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc.
Page 19 Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using Interior locking/unlocking the key integrated in the RENAULT door control card.
Page 20: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Operating faults You can decide whether you want to activate this function. If you experience an operating fault (no automatic locking, the indicator light in- Operating principle corporated in button 1 does not light up when trying to lock the doors and After the vehicle is started, the system boot, etc.), firstly check that the doors automatically locks the doors when...
Page 21: Front Headrests
FRONT HEADRESTS To adjust the angle of the headrest Depending on the vehicle, tilt section A towards or away from you to the re- quired position. To remove the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary).
Page 22: Heated Seats
FRONT SEATS WITH MANUAL CONTROL To tilt the seatback Turn control knob 3 to the required po- sition. Heated seats (depending on vehicle) With the engine running, turn control 4 to either position 1, 2 or 3 (depending on the temperature required). An in- dicator light on the instrument panel lights up once the front seat heating system is operating.
Page 23: Adjusting The Seat Position
FRONT SEATS WITH ELECTRIC CONTROL Heated seats (depending on vehicle) With the engine running, turn control 1 to either position 1, 2 or 3 (depending on the temperature required). An in- dicator light on the instrument panel lights up once the front seat heating system is operating.
Page 24 – with the “hands-free” RENAULT card adjustment buttons is pressed during detected or, depending on the vehi- recall. cle, the RENAULT card in the card When driving, it is not possible to reader; recall a driving position. – when the driver’s door is opened.
Page 25 ACCESS TO THE REAR SEATS Locking the seats When a person, an object or a child seat prevents the front seats from lock- ing, perform the following operations: – ask all of the passengers to leave the vehicle and remove any bulky objects from the rear seats;...
Page 26: Seat Belts
SEAT BELTS (1/3) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 27 SEAT BELTS (2/3) Unfastening Front seat belt reminder ß warning light Press button 4 and the seat belt will be This lights up on the central display rewound by the inertia reel. Guide the when the engine is started then, if the belt.
Page 28 SEAT BELTS (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 29: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) These are: – Have the entire restraint – front seat belt inertia reel preten- system checked following sioners; an accident. – chest-level load limiters; – No operation whatsoever – anti-submarining air bags; is permitted on any part of the system (pretensioners, air bags, –...
Page 30 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at Depending on the vehicle, the pres- an acceptable level.
Page 31 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation Special feature of the front air This system is only operational when the ignition is switched on. After a violent impact, it has two deploy- ment volumes and integrates a ventila- In a severe frontal impact, the air bags tion system: inflate rapidly, cushioning the impact...
Page 32 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 33: Methods Of Restraint In Addition To The Rear Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 34: Side Protection Devices
SIDE PROTECTION DEVICES Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. Warnings concerning the side air bag –...
Page 35: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
Page 36 PROTECTION DEVICES IF THE VEHICLE OVERTURNS Precautions Observe the safety instructions indi- cated on the arches 1. Automatic safety bars Operating faults The system comprises: Warning light 3 will light up on the in- strument panel when the ignition is –...
Page 37: If The Vehicle Overturns
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 38 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 39 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 40: Choosing Child Seat Mounting
CHILD SAFETY: choosing a child/baby seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX The seat belt must never seats: via the seat belt or using the system be twisted or the tension ISOFIX system. Authorised ISOFIX child seats are ap- relieved.
Page 41 CHILD SAFETY: choosing a child/baby seat mounting (2/2) The two rings 1 are located between The ISOFIX anchorage the seatback and the seat base of the points have been exclu- seat and are identified by a marking. sively designed for child To ensure your child seat can be easily seats with the ISOFIX fitted and locked on rings 1, use access...
Page 42: Fitting A Child Seat
CHILD SAFETY: fitting a child seat (1/4) Some seats are not suitable for fitting In the front seat In the rear side seat child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two...
Page 43 CHILD SAFETY: fitting a child seat (2/4) ² Seat not suitable for fitting child seats. Child seat attached using the ISOFIX mounting ü Seat which allows an ISOFIX child seat to be fitted. The size of the ISOFIX child seat is in- dicated by a letter: –...
Page 44 CHILD SAFETY: fitting a child seat (3/4) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Seat size Passenger front Type of child seat Weight of the child Rear side seats (5) seat (1) (2) ISOFIX...
Page 45 CHILD SAFETY: fitting a child seat (4/4) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal”...
Page 46: Deactivating/Activating The Front Passenger Air Bag
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a restraint system for a rear-fac- ing child in a seat protected by an ACTIVATED front AIRBAG.
Page 47 CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels B or C at A on each side of the passenger sun visor 3 (example: label shown above) remind you of these in- structions. DANGER Since operation of the front passenger airbag is not...
Page 48 CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended.
Page 49: Rear View Mirrors
REAR VIEW MIRRORS Folding door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position B). In this case, they will fold out when the ignition is next switched In any case, you can make the door mirrors fold in (switch 2 in position C) or fold out (switch 2 in position A).
Page 50: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 10 11 1.44...
Page 51: Instrument Panel
20 Retractable roof opening/closing. system information, etc. 3 Stalk for: 21 Engine start/stop button and – Driver and front passenger seat RENAULT card reader. – direction indicator lights, belt reminder warning light and 22 Central door locking/unlocking front passenger airbag activated/ –...
Page 52 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1.46...
Page 53 – activation/deactivation of the trac- – exterior lights, 23 Engine start/stop control and card tion control system; reader RENAULT. – front fog lights, – activation/deactivation of the 24 Location for radio, navigation – rear fog light. function Stop and Start.
Page 54 WARNING LIGHTS (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Side light tell-tale light Left-hand direction indicator tell-tale light Main beam headlight tell-tale Right-hand direction indica- á light tor tell-tale light Dipped beam headlight tell- Heated seats operating indi- ð...
Page 55 WARNING LIGHTS (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Speed limiter and cruise Front seat belt reminder Anti-lock braking warning Î ß control warning light warning light light See the information on the “Speed lim- This lights up on the central display This lights up when the ignition is iter”...
Page 56 WARNING LIGHTS (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Engine coolant temperature Oil pressure warning light Ô À warning light If it comes on on the road, ac- This lights up when the ignition is ®...
Page 57 INSTRUMENT PANEL: displays and indicators (1/2) Rev counter 1 (rpm × 1 000) Gear change indicator 3 The first time the alert appears, it can be cleared by pressing one of the but- This lights up to advise you to change tons on the end of stalk 2.
Page 58 INSTRUMENT PANEL: displays and indicators (2/2) Coolant temperature indicator 7 Speedometer 8 (kph or mph) Instrument panel in miles (option to switch to km/h) In normal use, indicator 7 should be Overspeed buzzer before area A. Under “intensive” op- – With ignition off, press button 10 erating conditions, the needle may ap- Depending on the vehicle and country, or 11 at the end of stalk 2 and the...
Page 59: Trip Computer And Warning System
TRIP COMPUTER: general information (1/2) c) mileage before service; d) tyre pressure monitor; e) vehicle settings customisation menu; f) trip log, operating faults and informa- tion message readout. Trip computer and warning Display selection keys 2 system 1 and 3 Depending on the vehicle, this includes Scroll through the following informa- the following functions:...
Page 60 TRIP COMPUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
Page 61 ON-BOARD COMPUTER: trip settings (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101668 KM a) Total mileage and trip mileage recorder. 112. 4 KM Fuel used Fuel used b) Journey parameters.
Page 62 ON-BOARD COMPUTER: trip settings (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Current Current Current fuel consumption. 7.4 L/100 This value is displayed above a speed of approximately 7.4 L/100 18 mph (30 km/h).
Page 63 ON-BOARD COMPUTER: trip settings (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message c) Mileage before service or oil change. Mileage before service Service in SERVICE With the ignition switched on, the engine not running and...
Page 64 ON-BOARD COMPUTER: trip settings (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) c) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on and the engine not running,...
Page 65 ON-BOARD COMPUTER: trip settings (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected FRONT TYRES d) Tyre pressure monitor Refer to the information under “Tyre pressure monitor” in Section 2. REAR TYRES 1.59...
Page 66 ON-BOARD COMPUTER: trip settings (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected e) Vehicle settings customisation menu. Settings menu: Enables certain vehicle functions to be set (instrument panel language, parking press and hold distance control, etc.).
Page 67: Steering Wheel
» switched off for some time whilst listening to the radio). « Please remove Request to remove the RENAULT card from the reader when you leave the vehicle. keycard » « Checking control Displayed with the ignition on when the vehicle is running self-diagnostics.
Page 68 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. ©...
Page 69 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.
Page 70: Power-Assisted Steering
STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering Operating faults The steering may become stiff when Variable power-assisted steering driving or when the steering wheel is The variable power-assisted steering turned repeatedly. This is due to the system is equipped with an electronic power assistance overheating.
Page 71: Vehicle Settings Customisation Menu
VEHICLE SETTINGS CUSTOMISATION MENU Once a line has been selected, keep pressing either button 2 or 3 to change the function: function activated < function deactivated If you select either “Parking sensor volume” or “LANGUAGE”, you will have to make a further selection (sound volume of the parking distance control or instrument panel language).
Page 72: Clock And Exterior Temperature
CLOCK AND EXTERIOR TEMPERATURE Vehicles equipped with a External temperature navigation system, radio, etc. indicator For vehicles which are not fitted with Special note: buttons 2 and 3, refer to the specific When the external temperature is be- equipment instructions to discover the tween –3°C and +3°C, the °C charac- special features.
Page 73: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
Page 74: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/3) Daytime running lights function Depending on the vehicle, the daytime running lights come on automatically when the engine is started. Main beam headlights á With the dipped beam head- lights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on.
Page 75 EXTERIOR LIGHTING AND SIGNALS (2/3) “See-me-home lighting” Special note: – If the dipped beam headlights are function manually switched on and if the light This function allows you to briefly switch is sufficient, the directional head- on the dipped beam headlights (to pro- lights will remain fixed;...
Page 76: Front Fog Lights
EXTERIOR LIGHTING AND SIGNALS (3/3) Front fog lights Switching off the lights Turn centre ring 4 on the Turn ring 4 again until mark 5 is oppo- stalk 1 until the symbol faces mark 5, site the symbol for the fog light you wish then release it.
Page 77 ELECTRICAL ADJUSTMENT OF THE DIPPED BEAM HEADLIGHTS Examples of positions for adjusting control A according to the load Driver alone or with front passenger Driver with one front passenger and one rear passenger On vehicles fitted with this function, control A allows you to adjust the height Driver with one front of the beams according to the load.
Page 78: Windscreen Wipers
WINDSCREEN WASH/WIPE (1/5) Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Vehicle fitted with intermittent Special note water; windscreen wipers When driving the vehicle, the wiping –...
Page 79 WINDSCREEN WASH/WIPE (2/5) Note: – the rain sensor is only intended as a driving aid. In the event of re- duced visibility, the driver should manually activate the wipers. In foggy weather or during snow- falls, wiping is not automatically triggered and remains under the driver’s control;...
Page 80 WINDSCREEN WASH/WIPE (3/5) Operating fault Special note In the event of a malfunction of the When driving the vehicle, the wiping automatic wiping, the wiper is set to speed slows down whenever the vehi- intermittent wiping. Contact an au- cle stops. For example, fast wiping thorised dealer.
Page 81: Service Position
WINDSCREEN WASH/WIPE (4/5) Specific front wiper position Note: (service position) Once the wipers have been switched off, at least 1 minute after locking the This position enables the blades to be vehicle, it is possible to manually move lifted to remove them from the winds- the blades.
Page 82: Windscreen Washer/Wiper
WINDSCREEN WASH/WIPE (5/5) Headlight washers Headlights on In the event of obstacles present On equipped vehicles, hold stalk 1 on the windscreen (dirt, snow, ice, pulled towards you for about 1 second, etc.), clean the windscreen (inclu- and the headlight washers and winds- ding the central area located behind creen washers will be activated at the the interior rear-view mirror) and...
Page 83: Fuel Grade
FUEL TANK (1/3) Fuel grade Vehicles running on ethanol-based fuel Use a good quality fuel that complies with the standards in force in the rele- It is essential to use unleaded petrol or vant country. The fuel must conform to fuel containing a maximum of 85% eth- the specifications indicated on cover B.
Page 84: Fuel Tank Filling With Fuel
FUEL TANK (2/3) Filling with fuel With the ignition off, insert the nozzle to open valve A and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation.
Page 85 FUEL TANK (3/3) Vehicles without priming bulb 2 Insert the RENAULT card into the card reader. Press the button without press- ing any of the pedals. Wait a few min- utes before starting. This will enable the fuel circuit to be primed. If the engine does not start, repeat the procedure.
Page 86 1.80...
Page 87 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting, stopping the engine .
Page 88: Running In
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm.
Page 89: Starting, Stopping The Engine
2 or in detection zone 3. When you get into the vehicle, insert the low (below – 10 °C): hold down the RENAULT card fully into card reader 2. clutch pedal until the engine starts. To start, depress the brake or clutch pedal and press button 1.
Page 90 In certain cases, the hands-free RENAULT card, insert the card into RENAULT card may not work: reader 2; – when the RENAULT card battery is – vehicles with a RENAULT “hands- drained, flat battery, etc. free” card, with the card in the pas- –...
Page 91 When you leave your vehi- the message “No keycard Press and cle, especially if you have hold” will appear on the instrument your RENAULT card with panel: press the button 1 for longer you, check that the engine than two seconds.
Page 92: Stop And Start Function
STOP AND START function (1/3) This system enables a reduced fuel The message “Auto Stop” on the instru- Special feature of the automatic consumption and lower greenhouse ment panel indicates that the engine is engine re-start gas emissions. on standby. Under certain conditions, the engine The system is activated automatically The vehicle equipment remain opera-...
Page 93 STOP AND START function (2/3) Conditions preventing the Special cases – the “Clear View” function is activa- ted (please see “Automatic Climate standby of the engine – While the system is operating, and Control” in Section 3); the engine is stopped (traffic jam, Certain conditions prevent the system –...
Page 94 STOP AND START function (3/3) Operating faults The system is automatically reactivated each time the vehicle is started using When the message “Check Stop & the start button (please see “Starting, Start” appears on the instrument panel stopping the engine)”. and the integrated warning light 2 lights up on the switch 1, the system is deac- tivated.
Page 95: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 96: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 97: Gear Lever
GEAR LEVER/HANDBRAKE Handbrake To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: Pull the lever 2 upwards and make sure the vehicle is immobilised. Make sure that the hand- brake is properly released Gear lever when driving (red indicator...
Page 98: Electronic Parking Brake
ELECTRONIC PARKING BRAKE (1/3) Note: To indicate that the electronic parking brake is released, a beep sounds and the message “Apply parking brake” ap- pears on the instrument panel: – with the engine running: when the driver’s door is opened; –...
Page 99: Manual Operation
Brief stop switch 3 at the same time; You can control the electronic parking To manually activate the electronic – remove the RENAULT card from the brake manually. parking brake, (when stopping at a red card reader. light, or stopping when the engine is Applying the electronic parking running, etc.): pull and release switch 3.
Page 100 ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic Operating faults – If there is an electronic parking brake ® fault, warning lights light up gearbox © – If there is a fault, the warning accompanied by the “Parking brake light illuminates on the instrument For safety reasons, automatic release fault”...
Page 101: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/3) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactur- ers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 102 DRIVING ADVICE, ECO-DRIVING (2/3) An overall rating from 0 to 100 is dis- – Avoid sudden acceleration. played to let you assess your eco driv- – Brake as little as possible. If you an- ing performance. The higher the score, ticipate an obstacle or bend in ad- the better your eco-driving perform- vance, you may then simply release...
Page 103 DRIVING ADVICE, ECO-DRIVING (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 104: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that fail- end of their service life, which will come ure to respect anti-pollution regulations The exhaust gas monitoring system will into force in 2015.
Page 105: Environment
This commitment is illustrated by the lation. less fuel (eg. 140 g/km, equivalent to Renault eco² signature. 5.3 l/100 km for a diesel vehicle). Recycling Our vehicles are also equipped with a Manufacture...
Page 106: Tyre Pressure Monitoring System
TYRE PRESSURE MONITORING SYSTEM (1/4) If the vehicle is equipped with the func- It should always be done after checking tion, this system monitors the tyre pres- the tyre pressure of all four tyres when sure. cold. Tyre pressures must correspond to the current usage of the vehicle (empty, Operating principle carrying a load, motorway driving, etc.).
Page 107 TYRE PRESSURE MONITORING SYSTEM (2/4) “Puncture” The wheel A, together with the warn- ing light 4 , indicates that the af- fected wheel is punctured or severely underinflated. Replace it or contact an authorised dealer if it is punctured. Top up the tyre pressure if the wheel is de- flated.
Page 108 TYRE PRESSURE MONITORING SYSTEM (3/4) “Check tyre pressure sensors” The warning light flashes for several seconds, then stays on, along with the message “Check tyre pressure sensors” and a missing wheel B. This message appears along with the © warning light. This message appears when at least one wheel fitted on the vehicle does not have sensors (e.g.
Page 109 TYRE PRESSURE MONITORING SYSTEM (4/4) Readjustment of tyre pressures The tyre pressures must be adjusted when cold (please refer to the label lo- cated on the edge of the driver’s door). If the tyre pressures cannot be checked when the tyres are cold, the recom- mended pressures must be increased by 0.2 to 0.3 bar (3 PSI).
Page 110: Driver Correction Devices/Aids
DRIVER CORRECTION DEVICES AND AIDS (1/4) ABS (anti-lock braking Depending on the vehicle, this is com- Operating faults: posed of: system) – the (anti-lock braking © – lit on the instru- Under heavy braking, the ABS prevents system); ment panel with the messages the wheels from locking, allowing the –...
Page 111: Electronic Stability Control
DRIVER CORRECTION DEVICES AND AIDS (2/4) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced under- ing fault the message “Check ESC”...
Page 112: Emergency Brake Assist
DRIVER CORRECTION DEVICES AND AIDS (3/4) The traction control system offers ad- Hazard warning lights switching on ditional safety. It is recommended that Depending on the vehicle, these may you do not drive with the function di- light up in the event of sudden decel- sabled.
Page 113 DRIVER CORRECTION DEVICES AND AIDS (4/4) Hill start assistance The hill start assistance This device assists the driver when system cannot completely starting on hills (ascending or descend- prevent the vehicle from ing). It prevents the vehicle from rolling rolling backwards in all sit- forwards or backwards by automatically uations (extremely steep gradients, applying the brakes when the driver lifts...
Page 114 CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you Controls Switching on stay within the driving speed limit that Press the side switch 1 . Warning 1 Main “On/Off” switch. you choose, known as the limit speed. light 7 comes on, lit orange, and the 2 Limit speed activation, storage and message “Speed limiter”...
Page 115: Speed Limiter
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any moment. To do this: press the accelerator pedal firmly and fully –...
Page 116 CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Putting the function on Recalling the limit speed Switching off the function standby If a speed has been stored, it can be re- The speed limiter function is deacti- called by pressing switch 5 (R). vated if you press switch 1: in this case The speed limiter function is deacti- a speed is no longer stored.
Page 117 CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an additio- nal driving aid. However, the function does not take the place of the driver. The cruise control function helps you to Controls Therefore, it can under no circums- maintain your driving speed at a speed tances replace the driver’s responsi- that you choose, called the cruising...
Page 118: Cruise Control
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving At a steady speed (above 20 mph Once a cruising speed is stored and Press switch 1 on the side showing (30 km/h) approximately) press the cruise control function is active, Warning light 7 comes on, lit green, and switch 2 (+): the speed is stored.
Page 119 CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed Putting the function on standby The cruising speed may be exceeded at any time by depressing the accele- The function is suspended when you: rator pedal. The cruising speed flashes –...
Page 120 CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed Note: if the speed previously stored is Switching off the function If a speed is stored, it can be recalled, much higher than the current speed, The cruise control function is deactiva- once you are sure that the road condi- the vehicle will accelerate more rapidly ted if you press switch 1: in this case a...
Page 121: Parking Distance Control
PARKING DISTANCE CONTROL (1/4) Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst re- versing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until This function is an addi- they become a continuous beep when...
Page 122 PARKING DISTANCE CONTROL (2/4) The system is designed to aid park- ing, and under no circumstances guar- antees a sufficient distance to operate the retractable roof. Before moving the roof in any way, first check that the sur- rounding space exceeds the required minimum distances (refer to the infor- mation on the “Retractable glass roof”...
Page 123 PARKING DISTANCE CONTROL (3/4) If there are obstacles located close to Adjusting the parking From the multimedia display A both the front and rear of the vehicle, (depending on vehicle) distance control volume only the closest of the two will be ac- Certain settings can be adjusted from knowledged and the corresponding From the customisation menu...
Page 124: Special Features
PARKING DISTANCE CONTROL (4/4) Park Assist Rear parking sensor Volume Rear camera view settings Image settings Done Prolonged deactivation of the From the multimedia display A Operating faults system Select “Menu”, “Settings”, “Park Assist” When the system detects an operating You may permanently activate or deac- then “Rear parking sensor”...
Page 125: Selector Lever
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Select position D. In most traffic con- ditions, you will not have to touch the gear selector lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particu-...
Page 126: Parking The Vehicle
AUTOMATIC TRANSMISSION (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – If the road contours and bends When the vehicle is stopped, move the move the lever to the left. Shifting the do not allow you to stay in auto- lever to position P while keeping your lever repeatedly allows you to change...
Page 127 AUTOMATIC TRANSMISSION (3/3) Operating faults – When driving, if the “Check auto gearbox” message appears on the instrument panel, it indicates a fault. Contact your approved Dealer as soon as possible. – When driving, if the message “Auto gearbox overheating” appears on the instrument panel, stop the vehicle to allow the gearbox to cool down.
Page 128 2.42...
Page 129: Your Comfort
Section 3: Your comfort Retractable glass roof ............Air Vents .
Page 130: Retractable Glass Roof
RETRACTABLE GLASS ROOF: conditions of use (1/2) Conditions of use – Do not operate the roof in minus temperatures. – Immobilise the vehicle on flat, level – If there is any ice or snow prevent- ground (not with two wheels on a ing the windows from lowering when kerb, for example) away from traffic.
Page 131 Driver’s responsibility Never leave your vehicle Operating the roof with the RENAULT card inside and never leave a child (or a pet) un- Before opening/closing the roof, ensure supervised, even for a short while. that the surrounding space is greater...
Page 132 RETRACTABLE GLASS ROOF: opening Before opening the roof – Perform the procedure with the engine running (risk of battery dis- charging) and the vehicle stationary. – Ensure that the boot divider 1 is well tensioned and that the boot is fully closed.
Page 133 RETRACTABLE GLASS ROOF: closing Before closing the roof Note: if you stop closing the roof during the operation, the roof will lower slowly – Perform the procedure with the in stages over 10 minutes. engine running (risk of battery dis- charging) and the vehicle stationary.
Page 134 RETRACTABLE GLASS ROOF: operating fault (1/2) – bring the roof out of the boot by moving the switch 1 forwards and pulling the switch 2 at the same time; – position the shelf under the boot by moving the switch 1 backwards and pressing the switch 2 at the same time;...
Page 135 RETRACTABLE GLASS ROOF: operating fault (2/2) Take the tool 4 out of the tool kit. From the driver’s seat: – Remove objects from the luggage – switch off the engine to exit safety compartment before closing the tail- mode; gate; –...
Page 136: Air Vents
AIR VENTS: air outlets (1/2) Depending on the vehicle: 6 right-hand side air vent 1 left-hand side air vent 7 passenger footwell heater outlets 2 left-hand side window demister 8 air conditioning control panel. outlet 3 windscreen demister outlets 4 centre air vents 5 right-hand side window demister outlet...
Page 137: Air Flow
AIR VENTS: air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Air flow Direction Turn control knob 1 (beyond the point Right/left: move tabs 2 to the right or of resistance).
Page 138: Manual Air Conditioning
MANUAL AIR CONDITIONING (1/2) Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed be- tween all the air vents, the front side window demisting vents, the...
Page 139 MANUAL AIR CONDITIONING (2/2) “OFF" position: the system is deactivated: the ventila- tion speed for the passenger compart- ment air is zero (vehicle stationary), you can however still feel a slight flow of air when the vehicle is moving. Recommended demisting option: Turn controls 1, 2 and 4 to the position.
Page 140: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL (1/5) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), whilst optimising consumption. The system controls the ventilation speed, air distribution, air recircula- tion, and starting and stopping the air conditioning and air temperature.
Page 141 AUTOMATIC CLIMATE CONTROL (2/5) Clear View function Press button 10: the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
Page 142 AUTOMATIC CLIMATE CONTROL (3/5) The displayed temperature values show a comfort level. When starting the engine, increas- ing or decreasing the value dis- played will not allow the com- fort level to be reached any more quickly. The system will always op- timise the temperature increase or decrease (the ventilation system does not start instantly at maximum...
Page 143 AUTOMATIC CLIMATE CONTROL (4/5) The air flow is directed to the Ø windscreen and the front side window demisting vents. The air flow is distributed be- × tween front side window de- misting vents, the windscreen demist- ing vents and the footwells. The air flow is directed mainly ¿...
Page 144 AUTOMATIC CLIMATE CONTROL (5/5) Recycling This function is managed automati- cally (operation is confirmed by warn- ing light 14 on display 12), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
Page 145: Air Conditioning: Information And Advice On Use
AIR CONDITIONING: information and advice on use Advice on use In some situations, (air conditioning Operating faults off, air recirculation activated, venti- Fuel consumption lation speed at zero or low, etc.) you As a general rule, contact your ap- You will normally notice an increase may notice that condensation starts proved Dealer in the event of an op- in fuel consumption (especially...
Page 146: Electric Windows
Driver’s responsibility Never leave your vehicle with the RENAULT card One-touch mode From the driver’s seat, use switch: inside and never leave a Depending on the vehicle, this mode 1 for the driver’s side;...
Page 147 ELECTRIC WINDOWS (2/2) One-touch mode operating faults In case of a fault when closing a window, the system reverts to normal mode: pull the switch concerned up as often as necessary to fully close the window (the window will close gradually), hold the switch (still on the closure side) for three seconds then lower and raise the window fully to reinitialise the system.
Page 148: Interior Lighting
INTERIOR LIGHTING (1/2) Courtesy light Glove box light 4 Tilt switch 2 to move it to the position Light 4 comes on when the cover is for: opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. This switches off after a time delay, once the doors concerned have been closed correctly;...
Page 149: Sun Visor
INTERIOR LIGHTING /SUN VISOR (2/2) Luggage compartment light 5 Sun visor Retractable roof blind Depending on the vehicle, light 5 Lower sun visor 6 or unclip it and turn it To close it, pull the blind using tab 8 comes on when the luggage compart- to cover the side window.
Page 150: Passenger Compartment Storage Space And Fittings
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/2) Door pockets 1 Front centre armrest storage compartment A Press button 2 and lift cover 3. Ensure that no hard, heavy Nothing should be placed or pointed objects are on the floor area in front of placed in the “open”...
Page 151 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/2) Glove box Rear centre console storage compartment 5 Pull handle 4 to open it. The glove box can hold A4-sized docu- ments, a large bottle of water, etc. Ensure that no hard, heavy or pointed objects are placed in the “open”...
Page 152: Accessories Socket 1
ASHTRAY, ACCESSORIES SOCKET Ashtray 2 To open, lift the cover. To empty, pull the ashtray towards you and it will be re- leased from its housing. Accessories socket 1 It is provided for connecting acces- sories approved by the Technical Department with a maximum power of 120 Watts (voltage 12 V).
Page 153: Luggage Compartment
LUGGAGE COMPARTMENT To open Operating faults Press button 1 and lift the luggage If the tailgate cannot be opened, it can compartment lid. be released manually: – insert the emergency key in the To close lock 2; – turn the key (movement A) then Lower the luggage compartment lid.
Page 154: Luggage Compartment Storage Space And Fittings
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS Storage under carpet 2 Luggage compartment Precautions (depending on vehicle) divider 4 Roof closed To access storage compartment 2, lift To separate the rigid roof from the load- Do not touch parcel shelf 1 with the ob- the luggage compartment carpet.
Page 155: Transporting Objects
TRANSPORTING OBJECTS: in the luggage compartment Transporting objects on the roof The fitting of roof bars is prohibited on this vehicle. Transporting objects in the luggage compartment Always position the objects transported Always position the hea- so that the largest surface is against the viest items directly on the partition.
Page 156: Equipment
TRANSPORTING OBJECTS towbar A = 1089 mm Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Choice and fitting of towing equipment Maximum weight of towing equip- ment: 22 kg For fitting and conditions of use, If the towbar ball obscures the regis- refer to the equipment’s fitting in-...
Page 157: Wind Deflector
WIND DEFLECTOR With the retractable glass roof open, Fitting the net wind deflector 1 for window 2 reduces Position the supports 6 in the hous- the movement of air in the passenger ings 8 and the rods 5 in the holes 7 lo- compartment.
Page 158: Multimedia Equipment
MULTIMEDIA EQUIPMENT Multimedia systems The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Multimedia display; 2 Radio; 3 Central control; 4 Multimedia sockets; 5 Steering column control;...
Page 159 Section 4: Maintenance Bonnet ............... . Engine oil level: .
Page 160: Bonnet
BONNET (1/2) To open, pull handle 1, located on the Unlocking the bonnet catch left-hand side of the dashboard. To release it, lift tab 2. Opening the bonnet Lift the bonnet; you will need to guide it as it is held by a strut. Before performing any action in the engine com- partment, the ignition must...
Page 161: Closing The Bonnet
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
Page 162 ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Oil level Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) ...
Page 163: Engine Oil Level
ENGINE OIL LEVEL: general information (2/2) Exceeding the maximum engine oil level Under no circumstances must the maximum fill level B be exceeded: risk of damage to the engine and catalytic con- verter. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
Page 164: Topping Up/Filling
ENGINE OIL LEVEL: topping up, filling (1/3) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
Page 165 ENGINE OIL LEVEL: topping up, filling (2/3) In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil.
Page 166: Oil Change
ENGINE OIL LEVEL: topping up, filling /OIL CHANGE (3/3) Oil change Service interval: refer Maintenance Document for your vehi- cle. Average capacity for oil Consult your approved Dealer at once if you notice an abnormal or changes repeated drop in any of the fluid Please refer to the maintenance docu- levels.
Page 167: Levels
LEVELS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 168: Brake Fluid Level
LEVELS (2/3) Level 2 Topping up It is normal for the level to drop as After any operation on the hydraulic cir- the linings become worn, but it should cuit, a specialist must replace the fluid. never drop below the “MINI” warning Only use fluids approved by our line.
Page 169: Windscreen/Headlight Washer Reservoir
LEVELS /FILTERS (3/3) Filters Liquid Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. Use a tool such as a needle to adjust the height of the windscreen washer Replacement intervals for filter ele- jets.
Page 170: Tyre Pressure
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure Tyre safety and use of snow chains: monitoring system Refer to the information on “Tyres” in Section 5 for the servicing conditions If under-inflated (puncture, low pres- and, depending on the version, the use of chains.
Page 171 TYRE PRESSURES (2/2) G: tyre pressure for the emergency spare wheel. H: emergency spare wheel tyre dimen- sion if different to the four tyres fitted to the vehicle. For your safety and to comply with the law. When they need to be re- placed, only tyres of the same make, size, type and profile should be used on a single axle.
Page 172: Battery
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the in- strument panel for the duration of the charging time.
Page 173 BATTERY (2/2) Replacing the battery Before performing any As this operation is complex, we advise action in the engine com- you to contact an approved Dealer. partment, the ignition must be switched off by pressing Vehicle fitted with the Stop and Start the engine stop button (please see function the information on “Starting, stop-...
Page 174: Bodywork Maintenance
BODYWORK MAINTENANCE (1/2) What you should not do A well-maintained vehicle will last Clean the retractable roof using high- longer. It is therefore recommended to pressure cleaning apparatus or clean Do not degrease or clean mechani- maintain the exterior of the vehicle reg- the retractable glass roof seals with a cal components (e.g.
Page 175 BODYWORK MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash – salt, particularly in the wheel arches and underneath the body after driv- finish Return the windscreen wiper stalk to ing in areas where the roads have the Park position (refer to the informa- This type of paint requires certain pre- been gritted.
Page 176: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 177 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
Page 178 4.20...
Page 179: Practical Advice
RENAULT card: battery ........
Page 180: Puncture
PUNCTURE, EMERGENCY SPARE WHEEL In the event of a puncture, Special note: depending on the vehicle, The Tyre Pressure Monitor function you will have: does not check the emergency spare wheel (the wheel replaced by the emer- An emergency spare wheel or tyre in- gency spare wheel disappears from the flation kit (refer to the information on the instrument panel display).
Page 181: Tyre Inflation Kit
TYRE INFLATION KIT (1/5) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 182 TYRE INFLATION KIT (2/5) Depending on the vehicle, remove the – adjust the pressure: to increase central partition in the storage compart- it, continue inflating with the kit, to ment to access the inflation kit. reduce it, turn button 7 located on the inflation adapter.
Page 183 TYRE INFLATION KIT (3/5) – affix driving recommendation label 9 Precautions when using the kit to the dashboard where it can easily The kit should not be operated for more be seen by the driver; than 15 consecutive minutes. – store the kit; –...
Page 184 TYRE INFLATION KIT (4/5) Engine running, handbrake applied: – after a maximum of 15 minutes, stop inflating and read the pressure (on – unroll the hose from the container; pressure gauge 14). – connect the compressor hose 12 to Note: while the container is empty- the container’s inlet 17;...
Page 185 TYRE INFLATION KIT (5/5) – Affix the driving recommendation Precautions when using the kit label to the dashboard where it can The kit should not be operated for more easily be seen by the driver; than 15 consecutive minutes. – Put the kit away. –...
Page 186 TOOLS Wheel bolt guide 4 To finish loosening or starting to tighten the wheel bolts. Hubcap tool 5 This tool is used to remove the wheel trims. Tow eye 6 Refer to the information on “Towing” in Section 5. Do not leave the tools un- secured inside the vehicle Key 7 as they may come loose...
Page 187: Wheel Trims - Wheel
WHEEL TRIMS - WHEEL Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, Remove using the hubcap tool 1 (lo- check that all the tools are correctly cated in the tool kit) by connecting the clipped into the tool kit, then position hook in the recess provided next to the it correctly in its housing: there is a...
Page 188: Changing A Wheel
CHANGING A WHEEL (1/2) Vehicles equipped with a jack and Offer up jack 4 horizontally; the jack wheelbrace head must be lined up with jacking point 1 located on the underside of the If necessary, remove the wheel trim. sill, closest to the wheel concerned, as Use wheelbrace 3 to slacken off the shown by arrow 2;...
Page 189 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mount- ing holes in the wheel are aligned with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
Page 190: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) Tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
Page 191: Tyre Pressures
TYRES (2/3) Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure tyres are cold; ignore higher pressures monitoring system Adhere to the tyre pressures (including which may be reached in hot weather If under-inflated (puncture, low pressure the emergency spare wheel).
Page 192 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- chains to the rear axle is strictly for- sary to observe the speed specified by For safety reasons, this op- bidden.
Page 193: Headlights (Changing Bulbs)
FRONT HEADLIGHTS: changing bulbs (1/3) After opening the bonnet, pull tool A Dipped beams Do not touch the bulb glass. Hold it upwards. Remove the two screws 1 by its base. from the headlight using the A tool. Halogen dipped beam headlight When the bulb has been changed, Unlock the two springs D, remove make sure you refit the cover correctly.
Page 194: Daytime Running Light
FRONT HEADLIGHTS: changing bulbs (2/3) Front side light Remove the cover E and pull the bulb holder 6. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced. Risk of injury. Before performing any Discharge bulb dipped beam Daytime running light action in the engine com- headlight...
Page 195 FRONT HEADLIGHTS: changing bulbs (3/3) Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. Daytime running lights 7 Please see an authorised dealer. Front fog lights 8 However, because the front bumper Any operation on (or mo- needs to be removed, you are advised dification to) the electri-...
Page 196: Rear Lights (Changing Bulbs)
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (1/2) Direction indicator light 3 Side light and brake light – From the luggage compartment, Consult an approved dealer. remove the screws 1 ; – from the outside, pull the light to- Rear fog light and reversing wards you (movement A);...
Page 197: Indicator Lights (Changing Bulbs)
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (2/2) High level brake light 5 Number plate lights 7 Indicator lights 8 Consult an approved Dealer. – Unclip light 7 by pressing tab 6; – Unclip indicator light 8 (using a flatb- lade screwdriver type tool positioned –...
Page 198: Glove Box Light
INTERIOR LIGHTING: changing bulbs (1/2) Courtesy light Glove box light – Set the three switches to the central Open the access cover 2, you can then position; unclip bulb holder 3 more easily. – move the courtesy light backwards Bulb type: C5W. (movement A) then tilt the front downwards (movement B).
Page 199: Luggage Compartment Light
INTERIOR LIGHTING: changing bulbs (2/2) Luggage compartment light Disconnect the light. Press tab 5 to release lens 7 and Unclip the light at 4 using a flat-blade access bulb 6. screwdriver or similar. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced.
Page 200: Fuses
FUSES (1/2) Fuse box Tweezers 1 If any electrical component does not Remove the fuse using tweezers 1, lo- work, check the condition of the fuses. cated at the back of cover A or B. Unclip cover A or B (depending on To remove the fuse from the tweezers, Check the fuse in question vehicle).
Page 201 FUSES (2/2) Allocation of fuses 9 Rear screen wiper; Some accessories are protected by fuses located in the engine compart- 10 and 11 Rear electric windows; (the presence of certain fuses depends ment in fuse box C. on the vehicle equipment level) 12 ABS/ESC ;...
Page 202: Connecting A Battery Charger
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers The battery charger must be com- (courtesy lights, etc.) are switched patible with a battery with nominal off before disconnecting or recon- voltage of 12 volts.
Page 203 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 204: Replacing The Battery
(insert the the next time the vehicle is started, the replace the RENAULT card battery, RENAULT card in the card reader) and message will disappear. press button 1 pulling on emergency lock/unlock the vehicle (refer to the in-...
Page 205: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only.
Page 206: Windscreen Wiper Blades
WINDSCREEN WIPER BLADES Check the condition of the wiper blades. You are responsible for their service life: – clean the blades and the wind- screen regularly with soapy water; – do not use them when the wind- screen is dry; –...
Page 207: Automatic Gearbox
If your vehicle is the towing vehi- or R for vehicles with automatic trans- cle, do not exceed the maximum towing missions), insert the RENAULT card in weight for your vehicle (refer to the in- the card reader then press the engine formation on “Weights”...
Page 208 Unclip cover 5 or 7 by sliding a flat tool These towing points may only be used (or the key integrated in the RENAULT for towing: never use them for lifting the card) under the cover.
Page 209 Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not Card battery is flat. Replace the battery. You can still lock/unlock and start lock or unlock the doors. your vehicle (refer to the information on “Locking/un- locking the doors”...
Page 210: Operating Faults
Starting conditions are not Please refer to the information on “Starting, stopping fulfilled. the engine” in Section 2. The hands-free RENAULT Insert the card in the card reader in order to start the card does not work. engine. Please refer to the information on “Starting, stopping the engine”...
Page 211 OPERATING FAULTS (3/6) On the road POSSIBLE CAUSES WHAT TO DO The steering column remains Steering wheel locked. Move the steering wheel while pressing the engine locked. start button (please refer to Section 2 “Starting/stop- ping the engine”). Faulty circuit. Consult an authorised dealer.
Page 212 OPERATING FAULTS (4/6) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine overheats. The Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an coolant temperature indica- approved dealer.
Page 213 OPERATING FAULTS (5/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
Page 214 OPERATING FAULTS (6/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The roof will not open/close or Sunroof opening/closing conditions Apply the opening/closing conditions (refer to the in- the roof opening/closing opera- not fulfilled. The message “Roof: see formation on “Retractable glass roof” in Section 3). tion is interrupted.
Page 215: Technical Specifications
Section 6: Technical specifications Vehicle identification plates ............Engine identification plates .
Page 216: Vehicle Identification Plates
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MAM (Maximum Authorised hicle identification plate should be Mass). quoted on all correspondence or 5 GTW (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MPAW (Maximim Permissible The presence and location of the in- Weight) for front axle.
Page 217: Engine Identification Plates
ENGINE IDENTIFICATION PLATES (1/2) Quote the information on the identi- fication plate or label A in all corre- spondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 218 ENGINE IDENTIFICATION PLATES (2/2) Quote the information on the identi- fication plate or label A in all corre- spondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 219: Dimensions
DIMENSIONS (in metres) 0.862 2.609 1.014 1.546 4,485 1.434* 1.547 1.810 Unladen...
Page 220: Engine Specifications
ENGINE SPECIFICATIONS Versions 1.2 TCe 1.6 16V 2.0 16V 2.0 T 1.5 dCi 1.6 dCi 1.9 dCi 2.0 dCi Engine type H5FT F4R Turbo (see engine plate) Turbo Cubic capacity (cc) 1197 1,598 1,998 1,998 1,461 1 598 1,870 1,995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
Page 221: Weights
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Total train weight (MTR) the information on “Vehicle identification plates”...
Page 222: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 223: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 224 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 225 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 226 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 227 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 228 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 229: Anticorrosion Check
ANTICORROSION CHECK (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 230 ANTICORROSION CHECK (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 231 ANTICORROSION CHECK (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 232 ANTICORROSION CHECK (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 233 ANTICORROSION CHECK (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 234 ANTICORROSION CHECK (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 235: Alphabetical Index
ALPHABETICAL INDEX (1/5) bulbs ABS ............. 1.49, 2.24 → 2.27 changing ............5.15 → 5.19 accessories................ 5.27 accessories socket ............3.24 catalytic converter............. 2.9 – 2.10 additional methods of restraint ....1.23 → 1.26, 1.29 central door locking ........1.8, 1.12 → 1.14 in the event of rolling ............
Page 236 ALPHABETICAL INDEX (2/5) doors/tailgate .........1.8 → 1.11, 1.14, 3.25 front passenger air bag deactivation ......... 1.40 driver’s position ............ 1.44 → 1.50 front seat adjustment ............1.16 driving ......2.2 → 2.5, 2.9 → 2.17, 2.20 → 2.41 front seats driving position adjustment ........
Page 237 ALPHABETICAL INDEX (3/5) horn ................... 1.67 adjustment ..............1.71 horn: changing bulbs ..........5.15 → 5.17 flash ................1.67 front ..............5.15 → 5.17 sounding the horn ............1.67 mobile directional ............1.69 hubcap tool ..............5.8 – 5.9 lights: adjusting...............
Page 238 ......... 3.11, 3.15 storage compartment..........3.22 – 3.23 rear view mirrors ..............1.43 storage compartments ........3.22 – 3.23, 3.26 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.14 sun visor ................3.21 RENAULT card switching on the vehicle ignition .......... 2.4 battery ................
Page 239 ALPHABETICAL INDEX (5/5) towing a caravan ............3.28, 6.7 wiper blades ..............5.28 towing equipment wipers ..............1.72 → 1.76 fitting ................3.28 blades ................5.28 towing hitch............5.8, 5.29 – 5.30 towing rings ........... 1.32, 1.34 – 1.35 towing weights ..............6.7 traction control ............
Page 242 à999108606Rë ú ë ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60 NU 1126-3 –...

Renault MEGANE COUPE CABRIOLET Driver's Handbook Manual

Table of Contents

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Section 6: Technical Specifications

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Renault MEGANE COUPE CABRIOLET

Summary of Contents for Renault MEGANE COUPE CABRIOLET

Table of Contents