Black & Decker MM2000 Instruction Manual
  1. Manuals
  2. Brands
  3. Black & Decker Manuals
  4. Lawn Mower
  5. MM2000
  6. Instruction manual

Black & Decker MM2000 Instruction Manual

20 inch (508mm) corded mower
Hide thumbs Also See for MM2000:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

20 inch (508mm) Corded Mower
INSTRUCTION MANUAL
CATALOg NUMBeR
MM2000
Thank you for choosing BLACk+DeCkeR!
PLeASe ReAD BefORe ReTURNINg ThIS PRODUCT fOR
ANy ReASON.
If you have a question or experience a problem with your BLACk+DeCkeR
purchase, go to http://www.blackanddecker.com/instantanswers
If you can't find the answer or do not have access to the Internet, call
1-800-544-6986 from 8 a.m. to 5 p.m. eST Mon. - fri. to speak with an agent.
Please have the catalog number available when you call.
SAve ThIS MANUAL fOR fUTURe RefeReNCe.
veA eL eSPANOL eN LA CONTRAPORTADA.
INSTRUCTIvO De OPeRACIÓN, CeNTROS De SeRvICIO y PÓLIZA De gARANTÍA.
ADveRTeNCIA: LÉASe eSTe INSTRUCTIvO ANTeS De USAR eL PRODUCTO.
key INfORMATION yOU ShOULD kNOw:
• Do not operate mower unless handle is locked into position.
• For best cutting results, keep blade sharpened and balanced.
• Inspect and thoroughly clean your mower after each use (a
deck with caked grass will degrade performance).
• Make sure mowing area is clear of other persons or pets prior
to starting and during operation.
To register your new product, visit
www.BlackandDecker.com/NewOwner

Advertisement

Table of Contents
loading

Frequently Asked Questions (11)

  • Why does my Black & Decker MM2000 keep shutting off during use?

    Your Black & Decker MM2000 may keep shutting off during use due to several reasons, along with their solutions:

    • Blade not free to turn: Release the bail handle to turn the mower off, unplug it, turn the mower over, and check that the blade is free to turn.
    • Overloading the mower: Avoid overloading the mower. Slow down your cutting pace or raise the cut height.
    • Abnormal vibration: If the mower starts to vibrate abnormally, release the bail handle to turn it off, unplug it, and check for the cause immediately. If the blade is damaged, replace it with a BLACK+DECKER replacement blade. If the underside of the deck is damaged, return the mower to an authorized BLACK+DECKER service center. If there is no visible damage but the mower still vibrates, disassemble the entire blade assembly as described in the "Removing and Installing Blade" section, remove any debris, clean each piece, and replace them. If it still vibrates, return the mower to an authorized BLACK+DECKER authorized service center.

    For more information, see page 13 of the manual.
    Was this helpful?
  • What troubleshooting steps should I take if my Black & Decker MM2000 won't start?

    If your Black & Decker MM2000 won't start, take the following troubleshooting steps:

    • Ensure the mower is properly plugged in and that the button on the switch box is completely depressed before pulling the bail handle.
    • Release the bail handle to turn the mower off, unplug it, turn the mower over, and check that the blade is free to turn.

    For more information, see page 13 of the manual.
    Was this helpful?
  • How do I change the blade on the Black & Decker MM2000 lawn mower?

    To change the blade on your lawn mower, follow these steps:

    1. Release the bail handle to turn the mower off, wait for the blade to stop, and unplug the mower.
    2. Cut a piece of 2x4 wood (27) (about 2 feet long) (610 mm) to keep the blade from turning while removing the nut (28).
    3. Wear gloves and proper eye protection. Turn the mower on its side, being careful of the sharp edges of the blade. Position the wood and unscrew the bolt with a 9/16" wrench (29).
    4. Note the orientation of each part as you remove it. Remove the nut (30), pull off the washer (31), the blade insulator (32), and the blade (33). Examine all pieces for damage and replace if necessary. The fan should not be able to be removed.
    5. To reassemble, slide the blade (33) on. It can only be attached to the fan in one direction and location. Line up the D-shaped hole of the blade with the D-shaped post of the fan, ensuring the writing on the blade faces out away from the mower. Place the insulator (32) on the blade so that the two outer ribs extend past the blade. Place the square washer (31) on top of the insulator so that it sits inside the two outer ribs on the insulator. Replace the nut (30) with the wide side against the washer.
    6. To tighten firmly, position the piece of wood as shown in Figure U to keep the blade from turning. Secure the nut with the wrench.
    7. Replace the blade on the mower and tighten securely.
    Was this helpful?
  • How do I adjust the cutting height on the Black & Decker MM2000?

    The cutting height on the Black & Decker MM2000 is adjusted by the central cut height adjust lever, which offers 7 positions. To set the height of cut:

    • Pull the mower cut height adjustment lever out of the locking notch.
    • Move the lever towards the rear of the appliance to lower the height of cut.
    • Move the lever towards the front of the appliance to raise the height of cut.

    If you are unsure which height to use, begin mowing with the cut height adjustment lever (7) in position 7 and adjust the height down as needed.


    For more information, see page 8 of the manual.
    Was this helpful?
  • What type of extension cord is recommended for the Black & Decker MM2000?

    To reduce the risk of electric shock, the Black & Decker MM2000 requires a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way; if it doesn't fit fully, reverse the plug. If it still doesn't fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way.

    For outdoor use, use an extension cord suitable for outdoor use, such as SW, SOW, STW, STOW, SJW, SJOW, SJTW, or SJTOW. Ensure the extension cord is in good condition and use the proper size for various lengths of cord and heavy enough to carry the current the tool will draw. Using an undersized cord can cause a drop in line voltage, resulting in loss of power and overheating.

    To reduce the likelihood of disconnection of the lawn mower cord from the cord set during operation, you can either:

    • Make a knot as shown in Figures A and A1.
    • Use one of the plug-receptacle retaining straps or connectors described in the manual (Figure B).

    For more information, see pages 4 and 5 of the manual.
    Was this helpful?
  • What should I do if my Black & Decker MM2000 is vibrating excessively?

    If your Black & Decker MM2000 is vibrating excessively, it is generally a warning of trouble. You should:

    1. Release the bail handle or switch lever (2) to turn the mower off.
    2. Wait for the blade to stop.
    3. Unplug the mower.
    4. Check for the cause immediately. If the blade is damaged, replace it with a BLACK+DECKER replacement blade. If the underside of the deck is damaged, return the mower to an authorized BLACK+DECKER service center.
    5. If there is no visible damage to the blade and the mower still vibrates, disassemble the entire blade assembly as described in the "Removing and Installing Blade" section. Remove any debris and clean each piece. Replace each piece as described in the "Removing and Installing Blade" section. If the mower still vibrates after these steps, return it to an authorized BLACK+DECKER service center.
    Was this helpful?
  • How do I assemble the Black & Decker MM2000 out of the box?

    To assemble your Black & Decker MM2000 out of the box, follow these steps:

    1. Prepare for assembly: Ensure the bail handle is released and the mower is unplugged.
    2. Attach the lower handle: Lift the lower handle (4) into place, making sure the arrow (15) on the base of the mower lines up with 1 or 2 on the base of the handle (16). Ensure each side of the lower handle is set on the same number.
    3. Close handle height adjust levers: Close the handle height adjust levers (6) as shown in Figure C, ensuring the teeth are engaged. If the connection between the handle and lever is too tight or loose, open the lever and adjust its depth by turning it, then close it again until the teeth are fully clasped and each lever stays securely closed.
    4. Attach the upper handle: Remove the upper-handle attachment levers (5), nuts (17), and washers (18) from the handle. Line up the holes on the bottom of the upper handle (3) with the holes on the top of the lower handle (4). Make sure the cord is located on the front of both handles. Slide the lever bolt through the holes from the outside of the upper handle, slide the washer over the bolt, and loosely assemble the entire assembly with the nut. Rotate the upper handle into its operating position. Close the lever; if it's too tight or loose, open it and turn the nut to adjust the clamping.
    5. Secure the motor cable: The motor cable (19) needs to be fixed to the handles using the cable restraints (20). Place the handles in the operating position, run the cable up the front of the lower and upper handles, pull back the cable restraint, and slide the motor cable under the clip, ensuring it is fully held in place.
    6. Bagging (Optional): Ensure the side discharge attachment (24) and mulching insert (23) are removed. Lift the rear door cover (9) and place the grass collection bag (8) onto the mower so the bag hooks (21) rest on the lugs (22). Then lower the rear door cover.
    Was this helpful?
  • How do I clean and maintain my Black & Decker MM2000 lawn mower?

    To clean and maintain your Black & Decker MM2000 lawn mower, follow these guidelines:

    • General Cleaning: After each use, inspect and thoroughly clean your mower. Release the bail handle (2) to turn the mower off, let the blade come to a stop, and unplug the mower. Use only mild soap and a damp cloth to clean the mower. Clean out any clippings that may have accumulated on the underside of the deck. After several uses, check all exposed fasteners for tightness.
    • Debris Removal: Keep the mower free of grass, leaves, or other debris build-up. Allow the mower to cool before storing.
    • Blade Care: Keep the blade sharpened and balanced for best cutting results. Mower blades are sharp, so wrap the blade or wear gloves, and use extra caution when servicing them.
    • Grass Catcher and Guards: Check grass catcher components and the discharge guard frequently and replace them with BLACK+DECKER recommended parts only when necessary. Ensure all guards are in place and working order.
    • Corrosion Prevention: Fertilizers and other garden chemicals contain agents that can accelerate the corrosion of metals. If you mow in areas where these have been used, the mower should be cleaned immediately afterward. Release the bail handle (2) to turn the mower off and unplug it, then wipe all exposed parts with a damp cloth. Do not pour or spray water on the mower to clean it. Do not store the tool on or adjacent to fertilizers or chemicals, as such storage can cause rapid corrosion.
    • Repairs and Service: Repairs, maintenance, and any adjustments not specified in the manual should be performed by BLACK+DECKER authorized service centers or other qualified service organizations, always using identical replacement parts.
    Was this helpful?
  • Can I sharpen the blade of my Black & Decker MM2000?

    Yes, you can sharpen the blade of your Black & Decker MM2000. For best mowing performance, keep the blade sharp. A dull blade does not cut grass cleanly. You should use proper eye protection while removing, sharpening, and installing the blade, and ensure the mower is unplugged. Sharpening the blade twice during a mowing season is usually sufficient under normal circumstances, but if your lawn has sandy soil, more frequent sharpening may be required as sand causes the blade to dull quickly. Replace bent or damaged blades immediately.


    For more information, see page 12 of the manual.
    Was this helpful?
  • What is the cutting width of the Black & Decker MM2000 lawn mower?

    The cutting width of the Black & Decker MM2000 lawn mower is 20 inches (508mm).

    Was this helpful?
  • Can the Black & Decker MM2000 be used to mulch grass clippings?

    Yes, the Black & Decker MM2000 can be used to mulch grass clippings. To do so, ensure the side discharge attachment (24) and the collection bag (8) are not attached. Then, lift the rear door cover (9) and slide the mulching insert (23) fully into the mower as shown in Figure H. Ensure the rear door cover (9) and side flap (25) fully close before turning the mower on.


    For more information, see page 8 of the manual.
    Was this helpful?
Need help?

Need help?

Do you have a question about the MM2000 and is the answer not in the manual?

Questions and answers

Related Manuals for Black & Decker MM2000

Summary of Contents for Black & Decker MM2000

  • Page 1 20 inch (508mm) Corded Mower INSTRUCTION MANUAL CATALOg NUMBeR MM2000 Thank you for choosing BLACk+DeCkeR! PLeASe ReAD BefORe ReTURNINg ThIS PRODUCT fOR ANy ReASON. If you have a question or experience a problem with your BLACk+DeCkeR purchase, go to http://www.blackanddecker.com/instantanswers If you can’t find the answer or do not have access to the Internet, call...

  • Page 2: Safety Guidelines - Definitions

    SAfety GuIdeLINeS - defINItIoNS it is important for you to read and understand this manual. The information it contains relates to protecting yOUR SAfeTy and pReVenTing pROblemS. The symbols below are used to help you recognize this information. dANGeR: indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
  • Page 3 to be used of objects such as rocks, never use mower in the rain. Always be sure of your footing; walk; never run. sticks, wire, toys, bones, etc., which 15. disengage the drive system, if so could be thrown by the blade. Objects equipped, before starting the motor.

  • Page 4: General Service

    GeNeRAL SeRVIce WARNING: GeNeRAL 1. never operate mower in a closed area. SAfety WARNINGS ANd INStRuctIoNS foR ALL 2. Keep all nuts and bolts tight to be moWeRS sure the equipment is in safe working • tHIS tooL cAN Be dANGeRouS. condition.
  • Page 5 • Don’t Abuse Cord – never pull lawn minimum Gauge for cord Sets mower by cord or yank it to disconnect Volts total Length of cord in feet 120V 0-25 26-50 51-100 101-150 from receptacle. Keep cord from heat, (0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m) oil, and sharp edges.

  • Page 6: Functional Description

    conditions that may affect their • The label on your tool may include the operation. A guard or other part that is following symbols. The symbols and their damaged should be properly repaired definitions are as follows: or replaced by an authorized service V ....volts center unless otherwise indicated mW....milliwatts elsewhere in this manual.
  • Page 7 lever and adjust the depth of the lever the clamping. check the levers by closing by turning the lever. close it again until them. They should be tight enough so the the teeth are fully clasped and each handles are held firmly, but loose enough so the levers can be fully closed.

  • Page 8: Side Discharge

    MULChING service center for repair if rear door does • ensure the side discharge attachment not close. (24) (Figure I) and the collection bag dANGeR: Sharp moving blade. (8) are not attached. never operate the mower in bagging • lift the rear door cover (9) and slide the mode unless the hanger hooks on the mulching insert (23) fully into the mower grass catcher are seated properly on the...
  • Page 9 • push the height adjustment lever into optimum results and to reduce the risk of cutting the main cable. one of the 7 locking notches. • place the bulk of the cable on the lawn, close to the starting point (position 1 in fig.
  • Page 10 shown in Figure O. • Open, but do not remove, the upper- handle attachment levers (5) and fold the upper handle (3) back over the lower handle (4) as shown in Figure P. MOWER OvERLOAD • The mower shold be compacted down To prevent damage due to overload conditions, do not try to remove too much grass at one time.
  • Page 11 STICKS, WIRE, BONES, AND OThER OR OTheR pARTS Of The blAde DEBRIS WhICh MIGhT BE ThROWN SySTem mAy cAUSe SeRiOUS injURy. By ThE ROTATING BLADE. WARNING: ReleASe bAil WARNING: hAndle TO TURn mOWeR Off, mow across the face WAiT fOR The blAde TO STOp, of slopes, never up-and-down.

  • Page 12: Blade Sharpening

    6. To tighten firmly, position the piece of instructions for blade balancing. wood as shown in Figure U to keep 7. Replace blade on mower and the blade from turning. Secure nut tighten securely. See instructions for with the wrench. removing and installing blade.

  • Page 14: Maintenance

    areas where fertilizers or chemicals have Limited two-year Home use been used, the mower should be cleaned Warranty immediately afterward as follows: black & decker (U.S.) inc. warrants Release bail handle (2) to turn mower this product for two years against any off and unplug mower.
  • Page 15 Tondeuse filaire de 508mm (20 po) MODe D’eMPLOI NUMeRO De CATALOgUe MM2000 Merci d’avoir choisi BLACk+DeCkeR! Consulter le site web www.BlackandDecker.com/NewOwner pour enregistrer votre nouveau produit. à LIRe AvANT De ReTOURNeR Ce PRODUIT POUR qUeLqUe RAISON qUe Ce SOIT : Si des questions ou des problèmes surgissent après l’achat d’un produit BLACk+DeCkeR, consulter le site web www.blackanddecker.com/instantanswers...
  • Page 16 voici une explication des symboles de bleSSURe cORpORelle, danger importants sur la tondeuse. nOTAmmenT leS SUiVAnTeS. 1. l’utilisateur doit lire LIRE TOUTES CES et comprendre le mode DIRECTIvES d’emploi. RÉDUCTION DES RISQUES ET DES BLESSURES : • Avant tout usage, veiller à ce que 2. pour réduire le risque de tout utilisateur de cet outil lise et blessures graves, ne pas comprenne toutes les directives...
  • Page 17 UTILISATION SUR UNE PENTE vers l’opérateur. dégager l’anse pour éteindre la tondeuse et arrêter la lame les pentes sont un facteur majeur de glis- avant de traverser une surface gravelée. sades et de chutes, qui peuvent entraîner 9. ne pas utiliser la tondeuse sans installer de graves blessures.
  • Page 18 Réparation, des dommages, avant de du respect des avertissements et démarrer et d’utiliser la tondeuse. directives de sécurité contenus dans 6. ne jamais effectuer de réglages ou de répa- ce manuel et indiqués sur la machine. rations lorsque le moteur est en marche ni Restreindre l’usage de cette tondeuse lorsque la tondeuse est branchée.
  • Page 19 ii) Utiliser l’une des courroies de fixation de engagée dans le dispositif de retenue de la prise ou l’un des connecteurs décrits la tondeuse. connecter la prise femelle dans le présent manuel (figure b). de la rallonge au cordon d’alimentation et brancher la tondeuse.

  • Page 20: Description Fonctionnelle

    congénitales et d’autres dangers pour la 4) Réparer tout dommage avant de démarrer et d’utiliser la tondeuse à gazon. reproduction. Voici quelques exemples de • Utiliser seulement des pièces de ces produits chimiques : rechange identiques. • composés présents dans les engrais • composés présents dans les CONSERvER CES MESURES. insecticides, herbicides et pesticides DANGER : AvERTISSEMENTS •...
  • Page 21 ASSEMBLAGE FIxATION DE LA POIGNÉE SUPÉRIEURE (FIGURE h) AvERTISSEMENT : Avant • Détacher les leviers de fixation de l’assemblage, s’assurer que l’anse est la poignée (6), les écrous (19) et les dégagée et que la clé de sûreté est retirée. rondelles (20) de la poignée. • Aligner les trous dans le bas de la FIxATION DE LA POIGNÉE poignée supérieure (4) sur les trous INFÉRIEURE...

  • Page 22: Éjection Latérale

    comme le montre la figure h. et s’assurer qu’il est bien maintenu en place par le dispositif de retenue. • Vérifier que le panneau/volet arrière (9) est bien fermé avant d’allumer la tondeuse. ÉJECTION LATÉRALE • S’assurer que le sac collecteur (8) est retiré. • Soulever le panneau/volet arrière (9) et glisser la pièce de déchiquetage (23) complètement dans la tondeuse comme le montre la figure h.

  • Page 23: Démarrage De La Tondeuse

    rythme. ne pas la surcharger. DANGER : Forte lame mobile. DANGER : Les lames rotatives peuvent causer des blessures graves. POUR éviter des blessures graves, débrancher la tondeuse, défaut de surveillance ou lorsque vous rechargez, nettoyage, entretien, transport, levage ou ranger la tondeuse. RÉGLAGE DE LA hAUTEUR DE LA POIGNÉE (FIGURE J) • Ouvrir les deux leviers de réglage de la...
  • Page 24 EDGEMAx™ nous vous recommandons d’utiliser votre tondeuse selon les instructions le dispositif edgemax™ (11) permet données dans cette section. Vous de couper l’herbe sur le bord d’un mur obtiendrez ainsi le meilleur résultat et ou d’une barrière (fig. N). le dispositif réduirez le risque de couper le câble edgemax™...

  • Page 25: Transport De La Tondeuse

    poignées de transport (10) commodes poignée vers l’avant de la tondeuse comme le montre la figure O. comme le montre la figure R. ne pAS essayer de soulever la tondeuse par la poignée supérieure (3) ou la poignée inférieure (4). • Ouvrir les leviers de fixation de la poignée (5), mais sans les enlever, et replier la poignée supérieure (3) vers...

  • Page 26: Affûtage De La Lame

    ET DÉBRANChER LA TONDEUSE enlever la rondelle (31), l’isolant de LORSQU’ELLE EST LAISSÉE SANS la lame (32) et la lame (33) comme SURvEILLANCE, MÊME POUR UNE l’indique la figure T. examiner les COURTE DURÉE. défauts de toutes les pièces et les remplacer si nécessaire.

  • Page 27: Équilibrage De La Lame

    DE LA LAME. S’ASSURER QUE LA sur un étau (36). Si l’une des extrémités TONDEUSE EST DÉBRANChÉE. de la lame pivote vers le bas, limer le tranchant de cette extrémité. la lame est deux affûtages par saison sont normalement correctement en équilibre quand aucune suffisants dans des conditions normales.

  • Page 29: Entretien

    GARANTIE LIMITÉ DE TROIS RENCONTRE CPSC ANS POUR UNE UTILSATION ExIGENCES DE SÉCURITÉ DOMESTIQUE blAcK+decKeR Tondeuse sont conformes aux normes de sécurité de black & decker (É.-U.) inc. garantit ce l’American national Standards institute, produit pour une durée de deux ans contre et de la commission de la sécurité...
  • Page 30 Segadora con cable de 508mm (20 pulg.) MANUAL De INSTRUCCIONeS CATáLOgO N° CS1015 gracias por elegir BLACk+DeCkeR! visite www.BlackandDecker.com/NewOwner para registrar su nuevo producto. LeA eL MANUAL ANTeS De DevOLveR eSTe PRODUCTO POR CUALqUIeR MOTIvO: Si tiene una consulta o algún inconveniente con su producto BLACk+DeCkeR, visite http://www.blackanddecker.com/instantanswers para obtener respuestas instantáneas las 24 horas del día.

  • Page 31: Lea Todas Las Instrucciones

    A continuación se presentan TOmAR pRecAUciOneS báSicAS de explicaciones de las ilustraciones SegURidAd pARA RedUciR el de importantes riesgos de seguridad RieSgO de incendiOS, deScARgAS correspondientes a la podadora. elÉcTRicAS y leSiOneS 1. el usuario debe leer y peRSOnAleS, inclUidAS lAS comprender el manual de SigUienTeS.

  • Page 32: Mantenimiento General

    una pared o contra algo que provoque 19. nunca se estire demasiado mientras una obstrucción. el material puede opera la podadora. Siempre asegúrese rebotar y golpear al operador. Al cruzar de tener los pies bien apoyados y de superficies de grava, suelte la palanca conservar el equilibrio en todo momen- del interruptor para apagar la podadora to mientras opera la podadora.
  • Page 33 hojas u otras acumulaciones de residu- ADvERTENCIA: os. espere a que la podadora se enfríe INSTRUCCIONES y antes de guardarla. ADvERTENCIAS GENERALES 5. Si golpea un objeto extraño, suelte DE SEGURIDAD PARA TODAS empuñadura de estribo (interruptor de LAS hERRAMIENTAS palanca) (2) para apagar la podadora, • ESTA hERRAMIENTA PUEDE SER espere que la hoja se detenga y desco-...
  • Page 34 desde el extremo e insértelo en la potencia y sobrecalentamiento. consulte abertura (13) como se muestra en la la tabla a continuación para conocer Figura B. empuje el cable prolongador las capacidades adecuadas de los dentro de las dos ranuras de sujeción cables.

  • Page 35: Mantenimiento Y Reparaciones

    inspeccione periódicamente los cables estado de california como causantes de prolongadores y reemplácelos si están cáncer, defectos de nacimiento u otros dañados. mantenga los mangos secos, problemas reproductivos. Algunos limpios y sin restos de aceite ni grasa. ejemplos de estos productos químicos son: • Mantenga los protectores en su lugar • compuestos en fertilizantes y en buenas condiciones.

  • Page 36: Descripción De Las Funciones

    DESCRIPCIÓN DE LAS FUNCIONES 1. caja del interruptor 2. mango de suspensión 3. mango superior 4. mango inferior 5. palancas de fijación del mango superior (2) 6. palancas de fijación del mango inferior (2) 7. palanca de ajuste de altura de corte 8.
  • Page 37 la cortadora de césped con facilidad. • Desde el exterior del mango superior (3), deslice el perno de la palanca a través de los orificios. • Deslice la arandela sobre el perno de la palanca y ensamble sin ajustar el ensamblaje completo con la tuerca. • Rote el mango superior a su posición de funcionamiento. • Cierre la palanca. Si está demasiado apretado o demasiado suelto, abra la palanca y afloje la tuerca para ajustar la sujeción.

  • Page 38: Descarga Lateral

    Asegúrese de que la cubierta de la apoye firmemente contra la parte superior del recolector de césped, ya que podrían puerta trasera (9) esté completamente cerrada antes de encender la cortadora producirse graves lesiones. de césped. ADvERTENCIA: permita que la cortadora de césped trabaje a su propio DESCARGA LATERAL ritmo.
  • Page 39 CORTAR (FIG. M - N) altura de corte. • Mueva la palanca hacia la parte ADvERTENCIA: SIEMPRE delantera del aparato para aumentar la INSPECCIONE EL ÁREA DONDE altura de corte. SEGADORA SE vA A UTILIZAR y • Empuje la palanca de ajuste de altura a ELIMINAR TODAS LAS PIEDRAS, PALOS, una de las 7 muescas de bloqueo. CABLES, hUESOS y RESTOS DE OTRO TIPO QUE PUEDAN SER LANZADOS POR LA CUChILLA GIRATORIA.
  • Page 40 ALMACENAMIENTO DE LA PROTECTOR DE SEGURIDAD y PUERTA TRASERA CORTADORA DE CÉSPED el protector de seguridad (39 en figura ADvERTENCIA: Una hoja girando h) está diseñado para minimizar el que puede provocar lesiones graves. Suelte la la hoja de la cortadora de césped arroje palanca de suspensión (2) para apagar la piedras u otros objetos hacia atrás desde cortadora de césped y quite la batería...
  • Page 41 2. Suelte la palanca del interruptor para apagar la podadora al cruzar cualquier área con grava (la hoja podría lanzar piedras). 3. para cortar el césped en terreno escabrosos o con malezas altas, seleccione la máxima altura de corte. Si intenta cortar demasiada cantidad de césped de una vez, puede causar que se sobrecargue el motor y que se detenga.
  • Page 42 AFILADO DE LA hOJA 3. Use guantes y protección adecuada para los ojos. gire la cortadora de césped mAnTengA lA hOjA AfilAdA pARA sobre un costado. Tenga cuidado con ObTeneR el mejOR RendimienTO de los bordes filosos de la hoja. coloque el lA pOdAdORA.

  • Page 43: Mantenimiento

    LIMPIEZA detenido y la cortadora de césped esté desenchufada antes de quitar la hoja.. Suelte la palanca del interruptor para 2. Retire la hoja de la podadora. consulte las apagar la podadora, espere hasta que la instrucciones para retirar e instalar la hoja. hoja se detenga y luego retire la llave de 3.

  • Page 45: Información De Mantenimiento

    GARANTÍA LIMITADO DE ACCESORIOS DOS AÑOS PARA USO EN EL lOS AcceSORiOS RecOmendAdOS pARA USO cOn lA pOdAdORA eSTán hOGAR diSpOnibleS en SU diSTRibUidOR black & decker (estados Unidos) inc. ofrece lOcAl O cenTRO de mAnTenimienTO una garantía de dos años por cualquier AUTORizAdO.
  • Page 46 · GARANTÍA BLACK+DECKER · BLACK+DECKER WARRANTy . SOLAMENTE PARA PROPOSITOS DE MExICO distributor name · Sello firma del distribuidor date of purchase · Fecha de compra Invoice No. · No. de factura PRODUCT INFOMATION · IdeNtIFIcacIóN del Producto cat. no. · catalogo ó Modelo Serial Number ·...
  • Page 47 SoLAmeNte pARA pRopoSItoS de mexIco Grupo Realsa en herramientas, Herramientas y equipos profesionales Av. colón 2915 Ote. S.A. de c.V. Súper manzana 69 mz.01 lote 30 col. francisco i. madero (Av. Torcasita) monterrey, nvo. león col. puerto juárez Tel. 01 81 83 54 60 06 cancún, quintana Roo Htas.
  • Page 48 90616861 September 2014 blAcK+decKeR copyright 2014 printed in china ©...

Table of Contents

Save PDF