Rainfresh BH010 Operating Instructions

High Flow Water Filter Models BH010 & BH020
INTRODUCTION
These units are for use in situations requiring flow rates up to 20gpm/75L/min (Model BH010 -13 3/4" Height) and 40gpm/151L/min (Model BH020 -
23 5/8" Height) These High Flow Water Filter Housings help protect plumbing fixtures, water heaters and appliances.
Unique double o-ring design provides an extra water tight seal.
Cartridge not included.
For dirt, rust, algae filtration use Rainfresh cartridges BC101, BC1 or BC3 in the BH010 and BC201, BC205 or BC225 in the BH020.
For taste/odour, chlorine and sediment reduction use BC2 in the BH010 and BC202 in the BH020 (Note: Rated flow for BC2 and BC202 is 3 US GPM and
6 US GPM only)
These units have 1" Female NPT Inlet and Outlet Threads.
Wrench included and Mounting Bracket sold separately
INSTALLATION PRECAUTIONS & OPERATING SPECIFICATIONS & GUIDELINES
For use on main cold water line only.
Always install after your pump and pressure tank or on city water after your meter and your main shut off valve.
Caution: The rubber O-rings provide a water tight seal between the head and sump. It is important that they are properly seated in the grooves of
the sump or a water leak could occur.
Use only with municipally treated or microbiologically safe water. The cartridges above Do Not remove harmful bacteria. For effective disinfection
install a Rainfresh DS3, UCSSM, UCS2, DS2, SST, FC000/1M or CT1M Drinking Water System or a R519, R830 or R1245 UV Water Disinfection system.
Do Not over tighten metal fittings into plastic filter head or it may crack.
Do Not use torch near plastic housing. If necessary, wrap a wet cloth around the pipe and head to absorb heat. All solder joints should be made
before joining pipe to the filter head.
Do Not install in direct sunlight
Do Not use wrench to tighten sump to head.
Do Not use sealer. Use thread seal tape for connections into unit. Allow at least three (3) inches above and below filter for
clearance. Protect your filter unit from freezing. Drain the unit if subject to freezing.
Max Operating Temperature: 100 o F / 38 o C. Prevent unit from freezing
Maximum operating pressure: 100 psi / 6.9 bar. If you suspect that your water
pressure will at any time exceed the rated pressure, a pressure
regulator must be installed before the filter housing. This will guard against
the water pressure exceeding the maximum pressure rating. It is
recommended that the pressure regulator be set at 75 psi / 5.2 bar or less.
ELECTRICAL GROUNDING: If water pipes are used to ground your
electrical system, install jumper wire across the filter unit.
INSTRUCTIONS FOR INSTALLATION
Instructions are for installing the BH010 housing on to 3/4" copper pipe using
copper or brass solder fittings. If the unit is to be installed on any other type of
pipe (plastic, PVC, Pex or Iron pipe) different hardware must be purchased.
Consult a qualified plumber or call Rainfresh for help.
Tools Required
Adjustable wrench, pipe cutter, file or sand cloth, thread seal tape,
soldering torch, flux & lead-free solder, pencil or marker
Fittings Required
- 1"NPT male adapters (2) and 1"x3/4" reducers (2), 3/4" unions (2). It is
recommended that you build a by-pass around the unit so that in case
filter needs to be removed for service, unfiltered water can still be
used in the house. To build the by-pass, you will need 3/4" copper
tees (2), 3/4" elbows (2) and 3/4" ball valves (3).
- The filter should only be installed vertically as shown. The inlet/outlet
ports can be on either side.
- Optional mounting bracket is sold separately (necessary for installation on PVC, plastic or PEX pipe).
Recommended Installation Procedure
Locate the best position for the water filter where there is easy access for
filter cartridge changes. This housing should be installed on the main water line right after the water meter or pressure tank. Allow at least three (3)
inches above and below filter for clearance. Some water spillage may occur during
filter cartridge changes. Therefore installing near a floor drain is preferable.
a) Solder the 1"x 3/4" reducer on to the 1" male adapters and solder at least 2" pipe length to it. Solder one end of the union to the other end
of the 2" pipe and allow to cool to room temp. Repeat for other side. Do not thread in adapters before soldering the reducers as soldering near the
ports can cause damage to the unit and may cause a leak.
b) Apply 4 to 5 wraps of thread seal tape, in a clockwise direction to the male threads of each adapter. DO NOT use pipe joint compound, wicking or
sealer on any parts connecting to filter housing.
INSTALLATION AND OPERATING INSTRUCTIONS
(Please read thoroughly BEFORE proceeding. Please save for future reference.)
Fig A
pg 1.