http://www.xiaoyu163.com TABLE OF CONTENTS -1/1 3 7 63 1515 0 SPECIFICATIONS ..............................3 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING............... 4 PRECAUTION TO REPALCE OPTICAL BLOCK (KSM-213 RDM) ..............5 ACCESSORIES PARTS LIST ..........................6 ELECTRICAL PARTS LIST ..........................7-20 TRANSISTOR ILLUSTRATION ..........................
http://www.xiaoyu163.com SPECIFICATIONS -1/1 3 7 63 1515 0 • Design and specifications are subject to change without notice L 13942296513 u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING -1/1 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
http://www.xiaoyu163.com PRECAUTION TO REPALCE OPTICAL BLOCK -1/1 (KSM-213 RDM) 3 7 63 1515 0 Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground Solder body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 X AS1001 87-A92-345-010 ANT,WIRE FM U (SEMI-ST) L 0 AS1002 87-A90-054-010 Ant. Loop AM-CON C...
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 0501 87-010-263-040 ELECT. CAP. 100UF +/-20% 0502 87-010-759-080 C-CAP, U 0.1UF-25V Z Y5V 0503 87-010-263-040 ELECT. CAP. 100UF +/-20% 0504 87-010-263-040 ELECT. CAP. 100UF +/-20% 0505 87-010-263-040 ELECT.
Page 8
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 0867 87-012-170-080 C-CPA, U 8 P-50V D C0G 0868 87-010-404-040 CAP.4.7UF M ELEC.50V P=2. 0869 87-012-286-080 C-CAP, U 0.01UF-25V K X7R 0871 87-012-195-080 C-CAP, U 100P-50V J C0G 0872 87-010-759-080 C-CAP, U 0.1UF-25V Z Y5V...
Page 9
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 0592 88-108-822-080 C-RES U 8.2K 1/16W J 0593 88-108-682-080 C-RES U 6.8K 1/16W J 0594 88-108-000-080 C-JUMPER, JR 1/16W J...
Page 10
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 FRONT 0331 87-012-184-080 C-CAP, U 33P-50V J C0G FRONT 0333 87-015-694-040 E-CAP.0.47UF M ELEC. 50V FRONT 0338 87-012-286-080 C-CAP, U 0.01UF-25V K X7R...
Page 11
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 FRONT 0344 88-108-563-080 C-RES. U 56K J 1/16W...
Page 12
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 MAIN 0116 87-A10-303-080 CAP. 0.047UF J Poly F 50V MAIN 0120 87-012-274-080 C-CAP, U 1000P-50V K X7R MAIN 0121 87-010-759-080 C-CAP, U 0.1UF-25V Z Y5V...
Page 13
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 MAIN 0640 87-A10-039-080 C-CAP 470P 50V J C0G CER. MAIN 0641 87-012-284-080 C-CAP, U 6800P-50V X7R...
Page 14
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 MAIN 0 PN 0101 8C-CL6-609-010 CONNECTOR ASSY 5P Pitch=2 MAIN ! S PR 0201 87-026-689-080 PROTECTOR 1A 60V 491 TYPE...
Page 15
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 MAIN 0131 88-108-153-080 C-RES, U 15K 1/16W J MAIN...
Page 16
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 MAIN 0281 88-108-562-080 C-RES U 5.6K 1/16W J MAIN 0282 88-108-562-080 C-RES U 5.6K 1/16W J...
Page 17
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 MAIN 0676 88-108-683-080 C-RES 68K 1/16W J MAIN 0677 88-108-683-080 C-RES 68K 1/16W J...
Page 18
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 TUNER 0932 87-012-286-080 C-CAP,U 0.01-25 K B GRM TUNER 0933 87-012-286-080 C-CAP,U 0.01-25 K B GRM TUNER 0934 87-012-286-080 C-CAP,U 0.01-25 K B GRM...
Page 19
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 TUNER 0901 89-503-602-080 C-FET,2SK360E TUNER 0902 87-A30-664-080 C-TR,2SC2620B...
http://www.xiaoyu163.com ELECTRICAL PARTS LIST -14/14 3 7 63 1515 0 • Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received. L 13942296513 u163 -20-...
http://www.xiaoyu163.com WIRING -5/5 (DECK) 3 7 63 1515 0 DECK C.B DECK R / P HEAD L 13942296513 CNA351 TO MAIN C.B CN351 u163 -31- http://www.xiaoyu163.com...
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-1/8 3 7 63 1515 0 1. Clock Adjustment Requirements Test point: TP1(IC301 85pin), GND Adjustment point: L301 1) While pressing and holding down the POWER button and the TUNER / BAND button, insert the AC plug to outlet. ±...
Page 37
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-2/8 3 7 63 1515 0 DECK ADJUSTMENT L 13942296513 1. Tape Speed Adjustment Requirements Measuring equipments : wow-flutter meter (frequency counter ) Test Tape: TTA-100 (3KHz) Test point: C651(Lch),C652(Rch),GND Adjustment point : Tape speed adjustment point (motor) 1) Connect Test point to the Wow - flutter meter.
Page 38
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-3/8 3 7 63 1515 0 3. Head Azimuth Adjustment Requirements Measuring equipment: Oscilloscope Test Tape: TTA-330 (8KHz) Test point: C651(Lch),C652(Rch),GND Adjustment point: Head azimuth screw 1) Connect the Test point to the oscilloscope of CH1 and CH2. 2) Set the V mode of the oscilloscope to ADD.
Page 39
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-4/8 3 7 63 1515 0 TUNER ADJUSTMENT 1. Clock Check Requirements Measuring equipment: Frequency counter Test point: TP1 (CLOCK), GND 1) Adjust the reception frequency of the main unit to 1710KHz. ± 2) Check that the test point frequency is 2160 0.045KHz.
Page 40
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-5/8 3 7 63 1515 0 < AM ADJUSTMENT> For AM adjustment, do wiring and connection as in the following. 5. If Adjustment Requirement Measuring equipment: Oscilloscope or Millivoltmeter Test point: TP8(Lch), TP9(Rch), GND Adjustment point: L802 1) Adjust the setting of Standard Signal Generator (hereinafter S.S.G.) to 999KHz of 30% variation.
Page 41
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-6/8 3 7 63 1515 0 < AM ADJUSTMENT> For AM adjustment, do wiring and connection as in the following. 7. Tracking Adjustment Requirement Measuring equipment: millivoltmeter Test point: TP8(Lch), TP9(Rch), GND Adjustment point: L904 1) Adjust the S.S.G. setting to 87.5KHz of 30% variation and reduce the output level all the way (till a certain degree of is monitored through the oscilloscope).
Page 42
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-7/8 3 7 63 1515 0 CD CHECK Perform the adjustments after the main unit enters the test mode. Place the CD mechanism on level ground. Equipment and tools required Measuring equipment Digital multi-meter Jitter meter (KIKUSUI 6235) Test disc: TCD-782 ATD-001 L 13942296513...
Page 43
http://www.xiaoyu163.com ELECTRICAL ADJUSTMENT-8/8 3 7 63 1515 0 3. Jitter Check 1) While oscilloscope is kept connected in the same test point as in step2. RF WAVEFORM CHECK, connect the output terminal of an oscillo scope to the input terminal of the jitter meter. 2) Set the VOLT range selector of oscilloscope to 500mV range or below.
http://www.xiaoyu163.com CD TEST MODE -1/1 3 7 63 1515 0 1. How to Start the CD Test Mode While pressing the CD OPEN/CLOSE button, insert the AC plug to the power outlet. When the test mode is started, the message [TEST] is displayed. 2.
http://www.xiaoyu163.com IC DESCRIPTION -1/3 (LC876748A-5Z32) -1/2 3 7 63 1515 0 Pin No. Pin Name I/O/C/P Description O-COCK CD control Q code clock signal output. O-RWC CD control command LAT signal output. O-CDIN CD control command data signal output. I-WRQ CD control SCOR signal input.
Page 48
http://www.xiaoyu163.com IC DESCRIPTION -1/3 (LC876748A-5Z32) -2/2 3 7 63 1515 0 Pin No. Pin Name I/O/C/P Description I-RDS Not use. VDD4 Digital power supply pin. D-VDD Not use. EZK-VDD Not use. IN-ECO Not use. 76-84 Not use. KSCAN Initial scan I/P.
Page 49
http://www.xiaoyu163.com IC DESCRIPTION -2/3 (LC78622NE) -1/2 3 7 63 1515 0 Pin No. Pin Name Description DEFI Defect sense signal (DEF) input pin. (Connect to 0V when not used) Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO.
Page 50
http://www.xiaoyu163.com IC DESCRIPTION -2/3 (LC78622NE) -2/2 3 7 63 1515 0 Pin No. Pin Name Description XVDD – Crystal oscillator power supply pin. XOUT Pin to which external 16.9344 MHz crystal oscillator is connected. XVSS – Crystal oscillator GND pin. Be sure to connect to 0V. SBSY Subcode block sync signal output pin.
Page 51
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (LA9241ML) -1/2 3 7 63 1515 0 Pin No. Pin Name Description Pin to which external pickup photo diode is connected. RF signal is created by adding with the FIN2 FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. FIN1 Pin to which external pickup photo diode is connected.
http://www.xiaoyu163.com IC DESCRIPTION -3/3 (LA9241ML) -2/2 3 7 63 1515 0 Pin No. Pin Name Description Pin from which TES signal is output to DSP. ÒHigh Frequency LevelÓ is used to judge whether the main beam position is on top of bit or on top of mirror.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 0 MC1001 8C-CL6-008-010 WINDOW,CASS,SAN,94HB,CHIM 0 MC1002 8C-CL6-006-010 LID CASS PS,HI650 THAI...
http://www.xiaoyu163.com COLOR NAME TABLE -1/1 3 7 63 1515 0 Basic color symbol Color Basic color symbol Color Basic color symbol Color Black Cream Orange Green Gray Blue Transparent Blue Gold Pink Silver Titan Silver Brown Violet White Transparent White Yellow Transparent Yellow Metallic Blue...
http://www.xiaoyu163.com MECHANISM PARTS LIST -1/1 (CMAL5Z213B) = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
http://www.xiaoyu163.com SPEAKER DISASSEMBLY INSTRUCTIONS -1/1 Type.4 Type.1 3 7 63 1515 0 TOOLS Insert a flat-bladed screwdriver into the position indicated by the Plastic head hammer arrows and remove the panel. Remove the screws of each speaker unit (-) flat head screwdriver andthen remove the speaker units.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL SX-SLEM30 YJMN O SP1001 88-NSK-610-010 SPKR, CERAMIC ASSY X SP1002 8B-CPX-016-010 BADGE,AIWA 27.5 O SP1003 8C-CP5-007-010 CORD,SPKR O O SP1004 8C-CP5-008-010 CORD,BUSH O O SP1005 8C-CP6-001-010 GRILLE,FRAME ASSY X SP1006 8C-CP6-002-010 NET, O SP1007...
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers. UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL XR-EM30 8C-CL6-851-010 CUSHION, FRONT 8C-CL6-851-010 CUSHION,REAR 8C-CL6-218-010 PLATE SHIELD TAPE 8C-CL6-029-010 SH,FL PC T=0.3/0.5mm[HONG 93-324-066-010 SH,FOAMED MAT 0.5-500-300...
http://www.xiaoyu163.com OTHERS PARTS LIST -1/1 (SX-SLEM30) = ! SAFTY PARTS = Components marked All components used on this model at the production line are shown in this service manual. 3 7 63 1515 0 However, please note that not all components will be available as spare parts for after-sales service. Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Page 62
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 2-11, IKENOHATA 1-CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111 0251431 http://www.xiaoyu163.com...