Disposizioni speciali: Misurazioni Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA...
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► BR87 User Manual...
Failure to do so may result in dam- the space provided in this manual. age to the quick couplers and cause overheating of The BR87 Hydraulic Breaker will provide safe and de- the hydraulic system. pendable service if operated in accordance with the in- •...
Page 6
(PPE) Personal Protection Equipment. seals may result. • Be observant of the hydraulic hoses lying about the work area, they can be a tripping hazard. • Always de-energize the hydraulic system when changing a tool bit. 6 ► BR87 User Manual...
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) BR87 User Manual ◄ 7...
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 10 ► BR87 User Manual...
3. Place the bit firmly on the surface to be broken. 4. Squeeze the trigger to start the breaker. Adequate down pressure is very important. When the tool bit breaks through the obstruction or becomes bound, release the trigger and reposition the tool bit. BR87 User Manual ◄ 11...
Always replace hoses, couplings and other parts • Do not use the tool for applications for which it was with replacement parts recommended by Stanley not intended. Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar.
Fluid leakage through charge Upper piston seal failure or Replace seals, recharge or replace accumulator valve cap. accumulator O-ring failure or diaphragm. accumulator charge loss or failure. Fluid leakage around trigger. Valve spool seal failure. Replace seals. BR87 User Manual ◄ 13...
If pressure is low, charge the accumulator as described in the following paragraph. 7. Tighten the 5/8-inch hex locking nut on the tool charging valve. Be careful not to overtighten. Install the protective cap and valve cap assembly. 14 ► BR87 User Manual...
1. Turn the tool upside down (without the tool bit) and spray oil through the drive hex and side holes in the breaker foot assembly to displace any remaining water in the lower piston cavity. BR87 User Manual ◄ 15...
Nominal Pressure ..........................1500 psi/103 bar Max Pressure ........................... 2000 psi/138 bar Max Relief Pressure ......................... 2150 psi/148 bar BR87 SOUND AND VIBRATION DECLARATION Test conducted on BR8713201,operated at 8 gpm input Measured A-weighted sound power level, Lwa (ref. 1pW) in decibels...
ROLL PIN, 3/16 × 1-1/2 11432 34127 CUP SEAL 11434 TRIGGER 04073 O-RING 74673 NAME TAG BR87 (ATTACH NEAR ITEM 60) 04074 ROD WIPER 04077 VALVE SPOOL, OC NOTE: There is a flow sleeve kit available P/N- 02494 HANDLE GRIP 05465...
ROV operation is still limited to the tool, for Depth (ft) 8 GPM 12 GPM example a percussive tool has the same depth 5/8” 5/8” limitation whether ROV or diver operated. 3/4” 1” 1” 1” 1000 1” 1-1/4” BR87 User Manual ◄ 21...
Page 22
Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...