Table of Contents
Advertisement
Quick Links
SET UP ANd OPERATINg INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
2006 by Harbor Freight Tools
©
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
3" PNEUMATIC
POLISHER KIT
Model
3491 Mission Oaks Blvd., Camarillo, CA 93011
95030
. All rights reserved. No portion of this
®
.
®
Revised 11h
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 95030
Summary of Contents for Central Pneumatic 95030
- Page 1 3” PNEUMATIC POLISHER KIT Model 95030 SET UP ANd OPERATINg INSTRUCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. distributed exclusively by Harbor Freight Tools ®...
-
Page 2: Product Specifications
Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 2... - Page 3 Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 3...
- Page 4 Harbor Freight Tools. NOTE: If an automatic oiler is not used, put 3-5 drops of pneumatic Tool Oil (not included) in the tool’s quick connector before each use. (See Figure A.) SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 4...
-
Page 5: Assembly Instructions
(not included) to the workpiece, install the Foam Pad (31) onto the 3” Pad (29). If buffing the workpiece, install the Buffing Pad (32) onto the 3” Pad. (See Figure C.) REV 06j SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 5... -
Page 6: Operating Instructions
(See Figure C.) Allow sufficient time for the wax to dry on the workpiece surface. SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 6... -
Page 7: Inspection, Maintenance, And Cleaning
NOTE: The most common error when polishing a workpiece is applying too much wax. If the Foam Pad (31) becomes too saturated with wax, polishing will SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 7... -
Page 8: Troubleshooting
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 8... -
Page 9: Parts List And Assembly Diagram
Front End Plate Buffing Pad Muffler Screw (2) Planet Gear Seat Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 9... - Page 10 This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 REV 11h SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 10...
Need help?
Do you have a question about the 95030 and is the answer not in the manual?
Questions and answers