Table of Contents
Advertisement
Quick Links
PALM ORBITAL WET SANDER
SET uP AND OPERATINg INSTRuCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANuAL.
©
Copyright
2007 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
5 INCH
Model
3491 Mission Oaks Blvd., Camarillo, CA 93011
97053
®
. All rights reserved. No portion of this
®
.
Advertisement
Table of Contents
Related Manuals for Central Pneumatic Professional 97053
Summary of Contents for Central Pneumatic Professional 97053
- Page 1 PALM ORBITAL WET SANDER 5 INCH Model 97053 SET uP AND OPERATINg INSTRuCTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. ® Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011...
-
Page 2: Important Safety Information
NOTICE is used to address practices not Notice related to personal injury. CAuTION, without the safety alert symbol, CAuTION is used to address practices not related to personal injury. SKU 97053 For technical questions, please call 1-800-444-3353. Page 2... -
Page 3: General Safety Rules
Valve Lever is dangerous and must be repaired. Disconnect the Sander from its compressed air supply source before making any adjustments, changing accessories, or storing the Sander. SKU 97053 For technical questions, please call 1-800-444-3353. Page 3... -
Page 4: Vibration Hazard
Wear suitable gloves to reduce the vibration effects on the user. Use tools with the lowest vibration when there is a choice between different processes. Include vibration-free periods each day of work. SKU 97053 For technical questions, please call 1-800-444-3353. Page 4... -
Page 5: Specific Safety Rules
Disconnect air hose and release any built-up air pressure. Never service the Sander with the air hose attached. Always release any built-up air pressure in the tool (even after disconnecting the air hose). SKU 97053 For technical questions, please call 1-800-444-3353. Page 5... -
Page 6: Specifications
1/4”-18 NPT Water Intake 11.5 Ft. x 1/4” O.D. Tube Size Accessories Sand Paper Discs: 2000 Grit / 1500 Grit / 1200 Grit / 800 Grit / (Qty. 1 Each) SKU 97053 For technical questions, please call 1-800-444-3353. Page 6... -
Page 7: Setup Instructions
FIguRE A For best tool performance, you should incorporate an oiler, regulator, and in-line water filter as shown in the illustration on the next page. (See Figure B, next page.) SKU 97053 For technical questions, please call 1-800-444-3353. Page 7... - Page 8 Place the Sander’s Anchor (43) Assembly in a container filled with cold, clean water. CAuTION! Use only cold, clean water. Never run the Wet Sander without a water source. (See Figure D.) WATER FLOW CONTROL FIguRE D ANCHOR ASSEMBLY (43) REV 08a SKU 97053 For technical questions, please call 1-800-444-3353. Page 8...
-
Page 9: Operating Instructions
Grip the Sander firmly. Then squeeze the Valve Lever (1) and allow the Pad (38) to move in its orbital motion to its fullest speed. To adjust the speed (orbits per minute) of the Sander, rotate the Regulator Set (29). (See Figure E.) SKU 97053 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Maintenance And Servicing
Then replace the Allen Screw. (See Figure E.) DAILY, check the Strainer (44) in the Anchor Assembly (43) for excess dirt and debris. If necessary, clean Strainer. (See Assy. Diagram.) SKU 97053 For technical questions, please call 1-800-444-3353. Page 10... -
Page 11: After Use
Using wrong tool for the job at Do not continue sanding to avoid after repeated brief hand. damaging workpiece surface. Use attempts. another method to remove residue. SKU 97053 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Parts List
Anchor Assembly 1 Set Shim Strainer Retainer Nut Binder Snap Ring Allen Screw (M5 x 10) Snap Ring (IR12) Bearing (60002RS) O-Ring (P8) Washer (M5) Valve Pin Sleeve Allen Wrench SKU 97053 For technical questions, please call 1-800-444-3353. Page 12... -
Page 13: Assembly Diagram
ASSEMBLY DIAgRAM 13-1 13-2 13-1 SKU 97053 For technical questions, please call 1-800-444-3353. Page 13... -
Page 14: Limited 1 Year Warranty
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 97053 For technical questions, please call 1-800-444-3353. Page 14...
Need help?
Do you have a question about the Professional 97053 and is the answer not in the manual?
Questions and answers