TRENDnet TEW-226PC Quick Installation Manual
Hide thumbs
Also See for TEW-226PC:
- Specifications (2 pages) ,
- Quick installation manual (23 pages) ,
- Quick installation manual (23 pages)
Advertisement
Quick Links
TEW-226PC/TEW-228PI Quick Installation Guide
This Installation Guide will lead you through the installation of CardBus/PCI
Wireless Adapter and the configuration utility. To establish your wireless
network connection, the following steps should be executed.
1.
Install the software using the installation CD.
2.
Install the Adapter card in the computer.
3.
Configure the Wireless Configuration Utility.
The product is designed to operate in Windows 98, Windows ME, Windows
2000, and Windows XP. And, the installation procedure for each operating
system is very similar.
Minimum Hardware Requirements
• Computer with an available 32-bit CardBus or PCI slot
• 300 MHz processor and 32 MB of memory
• CardBus Controller properly installed and working in the computer
• An 802.11b Access Point (for Infrastructure Mode) or another 802.11b
wireless adapter (for Ad-Hoc <Peer-to-Peer> networking mode).
(Not required for driver and configuration utility installation)
<Important>
DO NOT install the adapter in the computer. Please
follow the instructions below to install the driver and utility
before installing the adapter in the computer.
Installing the Driver and Wireless Utility for Windows 98/ME/2000/XP
1.
Insert the Driver & Utility CD-ROM into computer's CD-ROM Drive and it
will automatically start a setup menu. Simply follow the instructions on
the screen to install the driver and the utility. If your computer does not
start the setup menu automatically, you can to run the software manually
by clicking on "Start", choose "Run", type D:\autorun.exe in the dialog
box (assuming D: drive is your CD-ROM drive) and click "OK".
2.
Click "Install Software" button, the InstallShield Wizard screen appears,
and then click "Next".
(Recommended)
Page 1
English
V1.10 08182003
Advertisement
Related Manuals for TRENDnet TEW-226PC
Summary of Contents for TRENDnet TEW-226PC
- Page 1 English TEW-226PC/TEW-228PI Quick Installation Guide V1.10 08182003 This Installation Guide will lead you through the installation of CardBus/PCI Wireless Adapter and the configuration utility. To establish your wireless network connection, the following steps should be executed. Install the software using the installation CD.
-
Page 2: Regulatory Domains
English At the Country Domain Selection screen, select the country domain (please see the Regulatory Domain table on the next page). If you are not sure which domain to select, click on the domain to see a list of the included countries for that domain. - Page 3 English Maximum Radio Output Power for Each Domain Regulatory Domain Antenna Gain (dBi) Maximum Power Level (mW) Americas (FCC) Europe (ETSI) Israel Japan (MKK) Note: some countries may have domain that is different from the domains in the above table. It is users’ responsibility to ensure that the wireless channel configuration is compliant with the regulatory standards of these countries.
- Page 4 English bar at the lower right hand corner of the screen. If the icon is not on the screen, please go to “Start”, “Programs”, “802.11Wireless LAN”, “802.11b Wireless CardBus & PCI Adapter HW.11…”, and select “Wireless Configuration Utility”. 11. In default, the wireless adapter is configured to connect to the nearest Access Point (the one with the highest signal strength and without the encryption).
- Page 5 English Making a Connection Using Network Survey Tool: from the “Wireless Configuration Utility”, click on “Network”, the Utility scans and displays available wireless network connections in the surrounding area. The connections’ configurations, including SSID, MAC Address, Channel, Signal, WEP (encryption), and Mode are displayed on the screen (you may need to scroll to the right to see the configurations on the right).
- Page 6 English If the available network’s WEP is “No” (no encryption), click on its SSID and click “Connect” to connect to this network. If the network’s WEP is “Yes”, after clicking “Connect”, manually enter the “Security” information, and click “Apply”. • Network Mode: select “Infrastructure” when connecting to an “Access Point”...
- Page 7 English Hex: 26 characters, with any combination of numbers 0 ~ 9 and letters a ~ f (upper or lower case). • Manual Entry: input the keys manually. • Key 1 ~ 4: to increase the security level, you can input up to 4 Keys for the wireless connection, and then activate different key on different time/date.
-
Page 8: For Microsoft Windows Xp
English APPENDIX How to Check/Configure Network Adapter’s IP Address in Windows 98/ME/2000/XP To connect to a network, make sure the proper network settings are configured for the wireless adapter. For Microsoft Windows XP: From the desktop, right click on My Network Places >... -
Page 9: For Windows 2000 Users
English Static IP address Setup Select Use the following IP address (if you don’t have a DHCP server in the network) Input IP address, Subnet mask, and Default gateway Input DNS Click OK For Windows 2000 users: From the desktop, right click on my network places and select Properties >... - Page 10 English Static IP address Setup Select Use the following IP address (if you don’t have a DHCP server in the network) Input IP address, Subnet mask, and Default gateway Input DNS Addresses Click OK For Windows Me and 98 users: From the Desktop, right click on Network Neighborhood >...
-
Page 11: Technical Support
TRENDware website. TRENDware provides free technical support for all customers for the duration of the warranty period on this product. TRENDware Technical Support Tel: +1-310-891-1100 Fax: +1-310-8911111 E-mail: support@trendware.com www.trendnet.com Monday ~ Friday, 7:30AM ~ 6:00PM Pacific Standard Time (except holidays) Page 11...