Table of Contents
Advertisement
Models 801 / 903 / 2101
PATENT N
OS
CAN 2,105,426
USA 5,614,883 – 5,617,819 – 5,673,017 – 6,087,996
AND OTHER PATENTS PENDING
Printed in Canada
All rights reserved © Astroflex 2006
U S E R M A N U A L
(FRANÇAIS AU VERSO)
C
ONSULT
ADDITIONAL MATERIAL
July 2006
®
REMOTE CONTROL
ENGINE STARTER
For all gas- and diesel-
S
P
AFETY
RECAUTION SECTION
BEFORE USING THIS PRODUCT
S
OME FEATURES MAY REQUIRE
(N
powered vehicles
.
).
OT INCLUDED
Manufactured in Canada by:
193-127-318-01
Advertisement
Table of Contents
Related Manuals for AstroStart ASTROSTART 2101
Summary of Contents for AstroStart ASTROSTART 2101
-
Page 1: Remote Control
Models 801 / 903 / 2101 PATENT N CAN 2,105,426 USA 5,614,883 – 5,617,819 – 5,673,017 – 6,087,996 AND OTHER PATENTS PENDING Printed in Canada All rights reserved © Astroflex 2006 ® U S E R M A N U A L (FRANÇAIS AU VERSO) ONSULT AFETY... -
Page 2: Government Regulations
GOVERNMENT REGULATIONS This device complies with the requirements of Industry Canada (IC) - Management of Radio Frequencies, as specified in document CNR-210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. -
Page 3: Table Of Contents
THANK YOU FOR CHOOSING AN ASTROSTART Like you, Astroflex is concerned with the environment. This is why we are suggesting that you use the two-minute runtime when you remote-start your vehicle to warm up engine fluids. Ask your dealer. We take this opportunity to remind you to properly defrost your windows and remove all the snow on your vehicle before driving on public roads. -
Page 4: Safety Precautions
Make sure you comply with all local regulations, which may prohibit leaving your engine running when vehicle is unattended in a public place. • To ensure continued safe operation of your remote starter, ask your AstroStart dealer to periodically check and/or tune the remote starting system. •... -
Page 5: Safety Sequence For Manual Transmission Vehicles
SAFETY SEQUENCE FOR MANUAL TRANSMISSION VEHICLES Your remote starter was designed to force you to perform a series of actions that will ensure that the gearshift lever is in neutral position when you exit the vehicle. This series of actions is called a "Safety sequence" and is aimed at preventing any remote start in situations where remote starting the engine would not be safe. -
Page 6: The Remote Control
THE REMOTE CONTROL Your remote control works off two small 3 volts lithium batteries ( CR2016). See your dealer for replacement batteries or additional remote controls. The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots. -
Page 7: Start Commands
CONFIRMATION In all cases, your remote starter will confirm that a command has been received properly by flashing parking lights. The horn provides certain confirmations when connected to system (requires optional wiring and material). In this manual, confirmation signals are written in an abbreviated form; for example: (lights: 2) means that parking lights will flash twice. Confirmations are explained in more detail under each command. - Page 8 CONTINUOUS MODE The “Continuous Mode“ function allows to remove the key from the ignition while leaving the engine running. This convenient feature allows you to leave the vehicle for short periods of time while the climate controls remain on. UTOMATIC TRANSMISSION VEHICLES To access Continuous Mode, send start command (Model 801 - 2101...
-
Page 9: Lock/Unlock Commands
LOW TEMPERATURE MODE (Model 903 only) In Low Temperature (Sentinel) mode, system starts your engine automatically when temperature falls below a preset level (programmable during installation). See table. Factory default setting is shaded. Engine will run for programmed runtime (see table), after which system will wait 2½... -
Page 10: Antitheft (Circuit Disabler)
UNLOCK Press the button. Doors are unlocked and parking light flashes twice to confirm command has been received. The “Unlock“ function can be programmed and connected in such a way that the first Unlock command only unlocks the driver's door, while a following Unlock command unlocks the other door(s). Dome light will turn on for 30 seconds every time (optional connection during installation): •... -
Page 11: Code Learning Of Additional Transmitter(S)
PANIC (903 only) Panic mode is used to attract attention if you are in difficulties. This command will not be executed if engine is kept running by ignition key. Use the stop command to abort panic mode or depress brake pedal. Press and hold, for at least 4 seconds, any of the parking lights, horn, and dome light, depending on which is connected to system, for 30 seconds depending on programming during installation. -
Page 12: Gearshift Check Applicable To Automatic Transmission Vehicles
GEARSHIFT CHECK APPLICABLE TO AUTOMATIC TRANSMISSION VEHICLES If key must be in ignition for gearshift to be moved out of P, your vehicle is safe as long as keys are kept away from children. If, on the other hand, gearshift can be put in gear without the key being in the ignition, proceed with this simple check. •...