Table of Contents
Advertisement
The telescope is now balanced on the R.A. axis. It is not nec-
essary to balance the telescope on the Dec. axis, since the
optical tube's mounting plate is positioned so that the tele-
scope will automatically be balanced on that axis. When you
loosen the lock lever on one or both axes of motion and man-
ually point the telescope, it should move without resistance
and should not drift from where you point it.
Focusing the telescope
Point the telescope so the front end is aimed in the general
direction of an object at least 1/4-mile away. With your fingers,
slowly rotate the focusing knob until the object comes into
sharp focus. Go a little bit beyond sharp focus until the image
just starts to blur again, then reverse the rotation of the knob,
just to make sure you've hit the exact focus point.
If you have trouble focusing, rotate the focus knob counter-
clockwise as far as it will go. Look through the eyepiece while
slowly rotating the focus knob clockwise. You should soon see
the point at which focus is reached.
Do You Wear Eyeglasses?
If you wear eyeglasses, you may be able to keep them on
while you observe. In order to do this, your eyepiece must
have enough "eye relief" to allow you to see the entire field of
view with glasses on. You can try this by looking through the
eyepiece first with your glasses on and then with them off,
and see if the glasses restrict the view to only a portion of the
full field. If the glasses do restrict the field of view, you may be
able to observe with your glasses off by just refocusing the
telescope the needed amount.
If your eyes are astigmatic, images will probably appear the
best with glasses on. This is because a telescope's focuser
can accommodate for nearsightedness or farsightedness, but
not astigmatism. If you have to wear your glasses while
observing and cannot see the entire field of view, you may
want to purchase additional eyepieces that have longer eye
relief.
aligning the Finder scope
The finder scope must be aligned accurately with the tele-
scope for proper use. To align it, aim the main telescope in the
general direction of an object at least 1/4-mile away, such as
the top of a telephone pole, a chimney, etc. Do this by first
loosening the R.A. and Dec. lock levers. Position the telescope
so the object appears in the eyepiece's field of view and then
retighten the R.A. and Dec. lock levers. Use the slow-motion
control cables to center the object in the eyepiece.
Now, look in the finder scope. Is the object visible? Ideally, it
will be somewhere in the finder's field of view. If it is not, some
coarse adjustments of the two black nylon finder scope align-
ment thumb screws will be needed to get the finder scope
roughly parallel to the main tube.
Note: The image in the telescope's eyepiece will appear
inverted from left-to-right (mirror reversed), which is nor-
mal for telescopes that utilize a star diagonal. The image
in the finder scope is oriented the same as the naked
eye.
6
By loosening or tightening the alignment thumbscrews, you
change the line of sight of the finder scope. Continue making
adjustments to the alignment thumbscrews until the image in
both the finder scope and the telescope's eyepiece is exactly
centered. Check the alignment by moving the telescope to
another object and fixing the finder scope's crosshairs on the
exact point you want to look at. Then look through the tele-
scope's eyepiece to see if that point is centered in the field of
view. If it is, the job is done. If not, make the necessary adjust-
ments until the two images are centered simultaneously.
The finder scope alignment needs to be checked before every
observing session. This can easily be done at night, before
viewing through the telescope. Choose any bright star or
planet, center the object in the telescope eyepiece, and then
adjust the finder scope's alignment thumbscrews until the star
or planet is also centered on the finder's crosshairs. The finder
scope is an invaluable tool for locating objects in the night sky;
its usage for this purpose will be discussed later, in detail.
Focusing the Finder scope
If, when looking through the finder scope, the images appear
somewhat out of focus, you will need to refocus the finder
scope for your eyes. Loosen the lock ring located behind the
objective lens cell on the body of the finder scope (see Figure
3a). Back the lock ring off by a few turns, for now. Refocus the
finder scope on a distant object by threading the objective
lens cell in or out on the finder scope body. Precise focusing
will be achieved by focusing the finder scope on a bright star.
Once the image appears sharp, retighten the lock ring behind
the objective lens cell. The finder scope's focus should not
need to be adjusted again.
5. setting up and using the
Equatorial Mount
When you look at the night sky, you no doubt have noticed
that the stars appear to move slowly from east to west over
time. That apparent motion is caused by the Earth's rotation
(from west to east). An equatorial mount (Figure 6) is designed
to compensate for that motion, allowing you to easily "track"
the movement of astronomical objects, thereby keeping them
from drifting out of the telescope's field of view while you're
observing.
This is accomplished by slowly rotating the telescope on its
right ascension (R.A.) axis, using only the R.A. slow-motion
cable. But first the R.A. axis of the mount must be aligned with
the Earth's rotational (polar) axis—a process called polar
alignment.
Polar alignment
For Northern Hemisphere observers, approximate polar align-
ment is achieved by pointing the mount's R.A. axis at the
North Star, or Polaris. It lies within 1° of the north celestial
pole (NCP), which is an extension of the Earth's rotational
axis out into space. Stars in the Northern Hemisphere appear
to revolve around the NCP.
Advertisement
Table of Contents
