1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Touch terminals
  5. UP-5700
  6. Installation manual

Sharp UP-5700 Installation Manual

Pos terminal
Hide thumbs Also See for UP-5700:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
1. Removing the rear cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Replacing the rear cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3. Removing the top cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4. Replacing the top cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5. Removing the power supply unit and AC cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
6. Replacing the power supply unit and AC cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
7. Removing the LCD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
8. PS-RAM DISK: UP-P02MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
9. F-ROM DISK: UP-F04RB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
10. Cautions for UP-F04RB and UP-P02MB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
11. D-RAM disk: S.O. DIMM (Local purchase) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
12. MCR UNIT: UP-E12MR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
13. Adjusting the IRQ 10/11 on the ISA PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
14. RS232 & CENTRO I/F: ER-A8RS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
15. SRN I/F: ER-01IN-PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
16. REAR DISPLAY: ER-A8DP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
17. DRAWER UNIT: ER-03DW/04DW/05DW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
18. COM1, COM2, COM3/5, and COM4/6 Connector. . . . . . . . . . . . . . . . . . . . . . . . 10
19. REMOTE POLE DISPLAY UNIT: UP-P20DP . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
20. HDD KIT: DKIT-8671RCZZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
INSTA LLATIO N MA NUAL
POS TERMINAL
MODEL
CONTENTS
CODE: 00ZUP5700/IME
UP-5700
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

Advertisement

Table of Contents
loading

Related Manuals for Sharp UP-5700

Summary of Contents for Sharp UP-5700

  • Page 1: Table Of Contents

    INSTA LLATIO N MA NUAL CODE: 00ZUP5700/IME POS TERMINAL UP-5700 MODEL CONTENTS 1. Removing the rear cover ..........1 2.

  • Page 2: Removing The Rear Cover

    Precautions • Before installation, be sure to turn off the power. • Use gloves to protect your hand from being cut by the angle and the chassis. • Connect all the cables securely. When connecting or disconnecting the cables, be careful not to apply stress to the cables.
  • Page 3 To pull out the FFC, unlock the slider to pull it out in the same Cautions on handling connectors procedures as (1). • When connecting or disconnecting the following connectors, follow Replacement parts required when the OCNCW7218RC3J’s the procedures below. slider is broken Forcibly pulling up the slider further may cause the slider to drop and to be broken in the worst case.

  • Page 4: Replacing The Top Cabinet

    4. Replacing the top cabinet 6. Replacing the power supply unit and AC cord Install the top cabinet in the reverse order of removing. Before install- ing, make sure that each connector is connected securely. (The con- Install the in the power supply unit and AC cord in the reverse order nector of cable between the MAIN PWB and KEY I/F PWB of removing.

  • Page 5: Ps-Ram Disk: Up-P02Mb

    3) Remove the LCD invertor cable B from the Invertor PWB 8. PS-RAM DISK: UP-P02MB 4) Remove the LCD invertor cable A from the Invertor PWB 5) Remove the LCD cable from the Key I/F PWB Make sure to save data before installing this option. 6) Remove the Touch panel cable from the Key I/F PWB 1) Remove the top cabinet.

  • Page 6: F-Rom Disk: Up-F04Rb

    Insert the ROM disk aslant into the option ROM/RAM connec- tor. Do not insert the UP-F04RB/UP-P02MB upside down into the con- nector (CN1) on the UP-5700 main PWB upside down. b) Push the ROM disk until the ROM disk is locked by the arms of option ROM/RAM connector.

  • Page 7: D-Ram Disk: S.o. Dimm (Local Purchase)

    The connector (CN1) has the signal assignment designed only for the 45° UP-5700. 30° ~ 40° If you erroneously insert a general-purpose RAM board into the con- nector (CN1), the UP-5700 and general-purpose RAM board may be damaged. Upper slot Lower slot 1 1. D-RAM disk: S.O. DIMM 2) Grab the UP-F04RB/UP-P02MB’s PWB on the center part to push...

  • Page 8: Mcr Unit: Up-E12Mr

    6) Remove the option D-RAM disk. 13. Adjusting the IRQ10/1 1 on the ISA a) Open the arms of D-RAM connector right and left. PWB. b) The D-RAM disk will be lifted automatically. Adjust the IRQ10 and IRQ11 using the switches: S1 and S2 on the ISA PWB if an option equipment is connected to the ISA slot of the ISA PWB.

  • Page 9: Srn I/F: Er-01In-Pc

    If an I/F (locally supplied half-size PC card) other than the ER- 6) Connect the SRN cable to the I/F PWB. A8RS is connected to the ISA bus connector, it may be required to remove reinforcement angle when inserting the I/F. In this case, remove reinforcement angle , insert the I/F, then install reinforcement angle...

  • Page 10: Drawer Unit: Er-03Dw/04Dw/05Dw

    17. DRA WER UNIT: ER-03DW/04DW/05DW The ER-05DW is optionally available only for the UP-5700 Ver. V. Up to 2 drawer units can be connected. 1) Install the to the drawer cable and drawer earth cable 2) Install the two ferrite cores to the drawer cable.

  • Page 11: Com1, Com2, Com3/5, And Com4/6 Connector

    18. COM1, COM2, COM3/5, and Main PWB COM4/6 Connector 1) COM1 & COM2 • D-SUB 9pin Connector 1 2 3 S1 • CI signal of COM1 or COM2 and +5V power supply can be 1 2 3 switched in order to supply +5V power. S1=COM1 : 1=CI 3=+5V S2=COM2 : 1=CI...

  • Page 12: Remote Pole Display Unit: Up-P20Dp

    Request to Send Data terminal Ready Send Data Signal Ground — Signal Ground — Cable holder Receive Data Use the following type of cable holder supplied with the UP-5700. Data set Ready • "3N" (large type) Clear to Send – 11 –...
  • Page 13 6) Remove the Base cabinet from the pole cabinet How to Extend Display Pole The pole can be extended by installing the attached pole to the standard pole. COMPONENT LIST: NAME Q’ty Pole cabinet Pole extension Screw (M3 × 4) Pole connection Securing the UP-P20DP to Screw (M4 ×...

  • Page 14: Hdd Kit: Dkit-8671Rczz

    10) Install the attached pole cabinet to the pole cabinet to fix it Lowering the height of the UP-P20DP with the screw Remove the standard Pole and attach the Base cabinet to the Ratch . At this time, replace the standard Display cable and the Earth wire with the S type cable and wire Display cable...
  • Page 15 6) Remove the HDD cover from the Bottom cabinet. 5) Connect the HDD CABLE to the HDD unit. 7) Connect the HDD CABLE to the HDD connector: CN17 on the MAIN PWB. Connect the HDD CABLE with the 4 pins on the left side of the HDD unit open as shown in Figure A.

  • Page 16: Sharp Corporation

    © COPYRIGHT 1998 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted. In any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents