Maytag BRAVOS W10373814A Use And Care Manual page 18

TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the
cost of a service call ... In USA www.maytag.com/help - In Canada www.maytag.ca.
If you experience
Washer not performing as expected (cont.)
Fabric Damage (cont.)
Incorrect dispenser Clogged dispensers or laundry
operation products dispensing too soon.
Liquid chlorine bleach not
used in dispenser or Oxi Treat Stains
option not selected.
Error Code Appears in Display
oL (overloaded)
Load too large.
appears in display
uL (unbalanced load) Load not balanced. The washer is
appears in display running a load-balance correction
routine.
LF (too long to fill) Washer taking too long to fill.
Drain extends more than
appears in display
4.5" (114 mm) into standpipe.
Ld (too long to drain
Washer taking too long to drain
water ) appears in
water. Drain extends more than
display
4.5" (114 mm) into standpipe.
HC (Hot and Cold
Hot and cold inlet hoses have been
hoses reversed) installed incorrectly.
appears in display
Sd (Excess suds) Excessive suds in washer. Washer is
appears in display
running a suds reduction routine.
dL (Lid cannot lock)
appears in display
lid (Lid opened)
appears in display
18
Possible Causes
Liquid chlorine bleach may have been
added incorrectly.
An item in the load may be keeping
the lid from locking.
Washer lid left open.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Do not overfill dispenser. Overfilling causes immediate dispensing.
Always select Fabric Softener and/or Oxi Treat Stains options
to ensure proper dispensing.
Load dispensers before starting a cycle.
It is normal for small amounts of water to be remain in dispenser at
the end of the cycle.
Homes with low water pressure may result in residual powder in the
dispenser. To avoid, select a warmer wash temperature if possible,
depending on your load.
Use only liquid chlorine bleach in the Bleach dispenser.
You may use powdered or liquid laundry boosters in the Oxi
Treat Stains dispenser. Always select the Oxi Treat Stains option
for proper flushing of Oxi products from dispenser. Leftover
powder may be wiped out by hand, if needed. Otherwise,
select Oxi Treat Stains option with the next cycle to rinse
out dispenser.
If an overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Allow the machine to continue. If the dial is flashing and the
machine has stopped, redistribute the load, close the lid, and
press START/PAUSE.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "Installation Instructions".
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "Installation Instructions".
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Instructions".
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions. If the
dial is flashing, reselect your desired cycle using a cold wash
temperature, and press START/PAUSE. Do not add detergent.
Check for items directly under the lid.
Close the lid to clear the display. If the lid is left open for more
than 10 minutes, the cycle will reset and water in the washer
will drain.
Solution