Programmed Heater Operation; Programming The Clock And Timers; Using The Timers - Rinnai RHFE-950ETR Operation & Installation Manual

PROGRAMMED HEATER OPERATION

PROGRAMMING THE CLOCK AND TIMERS

The clock must be set before the timers will operate. The clock may need to be re-set
whenever the remote control batteries are changed.
This heater has two timers which allow the heater to start and stop during two distinct
periods each day.
The set temperature during timer operation is the temperature which was selected when the
heater was last used.
Clock Setting
1. Press the Time Set button
the function has been initiated. The Remote Display will show "AM 12:00"
2. Use the Up and Down buttons
press the Time Set button
If you do not want to set the timers at this point then press the Time Set
button 4 more times until the display returns to the time.
NOTE
If there is no button pressed for approximately 90 seconds then the screen
will deactivate and any settings that have not been transmitted will be lost.
Timer Setting
3. "Timer 1 Set ON"
buttons to set the desired "AM" or "PM" "ON" time. Press the Time Set button
12
once.
4. "Timer 1 Set OFF"
buttons to set the desired "AM" or "PM" "OFF" time. Press the Time Set button
12
once.
5. To set-up Timer 2 repeat steps 3. and 4 above or just press the Time Set button
three times to exit the timer set-up.
6. The set On/Off timers will be displayed briefly to confirm settings.
When the programs have been received the Remote Display will revert to Time mode
and .
24
After battery replacement the clock and timers may need to be re-
programmed.
NOTE

USING THE TIMERS

Prior to using timers ensure that the desired temperature has been set. See ADJUSTING
THE TEMPERATURE on page 11.
1. One or both Timers can be used. While the heater is in operation to start Timer 1 press
the Timer 1 button
The display briefly shows the status of each Timer (e.g. Timer 1 ON Timer 1 OFF). If the
current time is outside those programmed the heater will go in to stand-by mode and
the Timer Indicator
the Remote Control Display
2. To turn the Timer(s) off simply press the relevant Timer button again. The heater will
return to stand-by mode and the Operation Indicator
timers set the Timer Indicator
the Remote Control Display
When operated by the Timer(s) the Flame Function is not available. If desired
the flame picture can be controlled by raising or lowering the set temperature.
NOTE
Rinnai Australia
once. "Clock Set"
18
to set the desired "AM" or "PM" clock time. Then
12
once.
18
and "AM 06:00"
26 23
and "AM 09:00"
26 23
. To start Timer 2 press the Timer 2 button
14
will glow 'Green'. Each active timer
9
.
20
will go out and the timers are no longer be shown on
9
.
20
will be displayed to confirm that
25
will be displayed. Use the Up and Down
will be displayed. Use the Up and Down
15
/ are also shown on
26 27
will glow 'RED', if there are no
8
13
20
11
13
. 17
23
19
18
18
18
18
23
24
.
26
21
Lock OverrideAuto Off Flame
AM
PM
Temperature Time
Clock Set
Timer 1 Set ON OFF
Timer 2 Set ON OFF
STANDBY
Timer 1 14
ON
15
Flame Timer 2
Extra
Overide
16
Low
Time
Lock 18
Set
12
Lock OverrideAuto Off Flame
AM
23
PM
Temperature Time
25
Clock Set
Timer 1 Set ON OFF
Timer 2 Set ON OFF
Lock OverrideAuto Off Flame
AM
23
PM
Temperature Time
26
Timer 1 Set ON OFF
Timer 2 Set ON OFF
Lock OverrideAuto Off Flame
AM
23
PM
Temperature Time
26
Timer 1 Set OFF
Timer 2 Set ON OFF
Lock OverrideAuto Off Flame
AM
23
PM
Temperature Time
Timer 2 Set ON OFF
Timer 2 Set ON OFF
STANDBY
Timer 1 14
ON
15
Flame Timer 2
Extra
Overide
Low
Time
Lock
Set
Lock Auto Off Flame
AM
PM
Temperature Time
Timer 1 OFF
27 Timer 2 Set ON OFF
7
8 1
9
Operation Manual