Denon S-102 Service Manual page 55

Pin Port Port
No Function setting
81 P123 O
82 P122 O
83 P121 O
84 P120 O
85 VCC2
86 P30 O
87 VSS
88 P27 O
89 P26 O
90 P25 O
91 P24 O
92 P23 O
93 P22 O
94 P21 O
95 P20 O
96 INT5 INT
97 P16 O
98 INT3 INT
99 P14 O
100 P13 O
101 P12 O
102 P11 O
103 P10 O
104 P07 O
105 P06 O
106 P05
107 P04 O
108 P03 O
109 P02 O
110 P01 O
111 P00 O
112 P117
113 P116 O
114 P115 O
115 P114 O
116 P113 O
117 P112
118 P111 O
119 P110 O
120 P107/AN7
121 P106/AN6 AD
122 P105/AN5 AD
123 P104/AN4 AD
124 P103/AN3 AD
125 P102/AN2 AD
126 P101/AN1 O
127 AVSS
128 SW1_IN AD
Port Name
SAN_MOSI
/CODEC_RST
PRE_MUTE_SUB
HP_MUTE_SUB
- VCC2
BE/_DIR
- VSS
CODEC_CE
NC(L:Output)
DSP_IO_MUTE
/AD/DIG
/ERR_MUTE
/BSE
NC(L:Output)
NC(L:Output)
/PROTECT
NC(L:Output)
/REMOCON
NC(L:Output)
PRE_MUTE_MAIN
/COMP_MUTE
/S/V_MUTE
/BE RST
DRV_ON
SYS_REQ
I BE ON
NC(L:Output)
NC(L:Output)
/DIR_RST
DIR_CE
DIR/CODEC_CK
I DIR_MISO
DIR/CODEC_MOSI
/DSPROM_RST
/DSP_RST
DSP_CS
I FLAG0
FAN_ON
FAN SPEED
I Pull uÇê
KEY2
KEY1
KEY0
MODE2_S102
MODE1_S102
Pull up
- AVSS
SW1_IN
Explanation
Serial Data output to TUNER/RDS IC
Reset output to CODEC
MUTE output to PRE OUT. H:MUTE
MUTE output to HEAD PHONE output. H:MUTE
Positive power
Select audio line output.(H:ESS,L:DIR)
GND
Chip Enable output to CODEC
Not Used:N.C.
DSP IO MUTE output(H:Mute)
Select audio line output.(H:DIGITAL, L:ADC IN)
MUTE output at DSP Error.
Bit Stream Enable output(L:Enable)
Not Used:N.C.
Not Used:N.C.
Protect Signal input.
Not Used:N.C.
Remote Control signal input
Not Used:N.C.
MUTE output to Output(H:Mute).
COMPONENT VIDEO Mute output(H:Mute)
S/COMPOSITE VIDEO Mute output(H:Mute)
Reset output to ESS
DRIVE POWER ON output(H:P.ON)
SYSTEM REQEST output to ESS.
Active Flag input from ESS.
Not Used:N.C.
Not Used:N.C.
Reset output to DIR.
Chip Enable output to DIR
Serial Clock output to DIR/CODEC.
Serial Data input from DIR.
Serial Data output to DIR/CODEC
Reset output to DSP ROM.
Reset output to DSP.
Chip Select output to DSP
DSP FLAG0 input
FAN ON/OFF output.H:FAN ON
FAN SPEED Control output(H:Slow L:Fast)
Pull up
Unit Operation Button input2
Unit Operation Button input1
Unit Operation Button input0
Initial Setting input for Region No of DVD.
Initial Setting input the destination.(E2,E3)
Pull up
GND
Select signal input of Video Signal. (H:HDMI/M:PROGRE/L:INTERLACE)
[ ]:Reserved
55
S-102