Surround; Pl Ii (Pro Logic Ii) Music Parameter; Cs Ii (Circle Surround Ii) Parameter; Multi Room - Marantz SR5500 User Manual

4 SURROUND

4 S URROUND
S URR . MOD E : AU T O
H T - EQ : O F F
L F E L E V E L : 0 d B
MA I N E X I T
1.
Select "SURROUND" in the SETUP MAIN
MENU with the or cursor buttons, and
press the ENTER button.
2.
To select a desired content , press the or
cursor buttons.
SURR.MODE:
Select the desired surround mode with the
cursor buttons.
HT-EQ:
Select to active the HT-EQ with the or cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is
because film soundtracks were designed to be
played back in large movie theater environments.
Activating the HT-EQ feature when watching a
film made for movie theaters corrects this and
restores the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included
in the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the or
cursor buttons.
After you complete this portion of the set up, move
the cursor to "MAIN" with the or cursor buttons
and press the ENTER button.
20
SR5500U DFU_01_ENG 2_2
Page 20
5 PL II (PRO LOGIC II)
MUSIC PARAMETER
Pro Logic II-Music mode creates a rich and
enveloping surround ambience from stereo
sources such as CDs.
In this mode, SR5500 includes three controls to
fine-tune the soundfield as follows.
5 P L II MU S I C P ARAME T E R
P ARAME T E R : D E F AU L T
P ANOR AMA : O F F
D I MEN S I ON : 3
C E N T E R W I D T H : 3
MA I N E X I T
Select "PL II MUSIC" in the SETUP MAIN MENU
with the or cursor buttons, and press the
or
ENTER button.
PARAMETER:
Select "DEFAULT" or "CUSTOM" with the
cursor buttons.
If you select "CUSTOM", you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the
or cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between 0 and 6 level in
1 level intervals with the or cursor buttons.
Adjust the soundfield either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with
certain recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the or cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the
center is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If "NONE" was selected for the Center speaker
setting, in the Speaker size set up menu, then
this setting will not appear.
After you complete this portion of the set up, move
cursor to "MAIN" with the or cursor buttons and
press the ENTER button.
6 CS II (CIRCLE SURROUND II)
PARAMETER
6 C S II P ARAME T E R
T RUBA S S : 0
S R S D I A L OG : 0
MA I N E X I T
1.
Select "CS II" in the SETUP MAIN MENU with
the or cursor buttons, and press the
ENTER button.
2.
To Select desired contents as below, press
the or cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in
1 level interval with the or cursor buttons.
TRUBASS produced by the speakers are an
octave below the actual physical capabilities of the
or
speakers adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the or cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If "NONE" was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to "MAIN" with the or cursor buttons and
press the ENTER button.
Adobe PageMaker 6.5J/PPC
04.8.2, 4:13 PM

7 MULTI ROOM

SR5500 has features in MULTI ROOM SYSTEM
such as source selector, sleep timer, Multi Room
Speaker output and remote control.
You can set these feature in this sub-menu.
7 MU L T I ROOM
A UD I O : D V D
S L E E P T I ME R : O F F
✽ ✽ ✽
MU L T I : O F F MS PK B :
✽ ✽ ✽
V O L : V AR I VO L :
✽ ✽ ✽
L E V E L : - 9 0 d B L E V E L :
- - - - MA I N - ROOM S T A T U S - - - -
V I D EO : D V D AUD I O : D V D
MA I N E X I T
1.
Select "MULTI ROOM" in the SETUP MAIN
MENU with or cursor button, and press
the ENTER button.
2.
To Select desired contents, press or
cursor button
AUDIO:
Select the audio source of the Multi-room output
with or cursor buttons.
SLEEP TIMER:
SLEEP timer function is available during the
multiroom is active, set the time with or
cursor buttons.
MULTI (MULTI ROOM):
To switch on the Multi-room output ON or OFF,
press or cursor button.
VOL (VOLUME SETUP):
Select whether the Multi-room output level is
variable or fixed with a or cursor buttons.
LEVEL (VOLUME LEVEL):
Adjust the Multi-room output level with or
cursor buttons.
MSPK B (MULTI SPEAKER B):
To switch on the Multi-speaker B output ON or
OFF, press or cursor buttons.
Note:
• This setting can be changed when the Surr Back is
set "NONE" in 2-1 SPEAKER SIZE menu.
When this setting is unavailable, "✽✽✽" is
displayed
VOL (VOLUME SETUP):
Select whether the Multi-speaker output level is
variable or fixed with a or cursor buttons.
Note:
• This setting can be changed when the Surr Back is
set "NONE" in 2-1 SPEAKER SIZE menu.
When this setting is unavailable, "✽✽✽" is
displayed