Enter The Cooling Program; Enter The Heating Program - White Rodgers 1F95-1277 Installation And Operating Instructions Manual

PROGRAMMING
Programming Tip: Copy Program
When programming your thermostat, you may copy the pro-
gram from one day to another day or group of days using the
Copy key . In 7 day programming mode, a day can be copied
to another day or all six other days . In 5/1/1 day programming
mode the weekday (Mon – Fri) program can be copied into
Sat and Sun or either Sat or Sun .
To copy a program from one day to another:
1) In Set Schedule mode, enter the program for the day or
select the day you wish to copy by pressing Advance
Day .
2) Press Copy . The display will show "Copy" next to the
SYSTEM key and the day of the week that will be copied .
3) Press Advance Day . The day being copied will be indi-
cated and the other days will be flashing.
4) If you wish to copy to all days skip to next step or press
Advance Day until the day you wish to copy to is flashing.
5) Press Copy . "Copy" will disappear, the day you copied
from will disappear and the day(s) you copied to will be
on .
6) If you wish to copy this same program into other days,
press Copy and repeat steps 3, 4 and 5 .
7) Press Run Schedule to return to normal operation .
Fill in the blank schedule on the next page then:

Enter the Heating Program

1) Press the Menu button and then press Set Schedule .
Press SYSTEM button to select either "Heat" or "Cool" in
the system switch area indicating the active mode being
programmed . You can switch to the other mode by
pressing the system switch at any time .
2) The top of the display will show the day(s) being pro-
grammed . The time and set at temperature are also
displayed . "Morning" will also be displayed to indicate
the period .
3) Press or key to change the temperature to your
selected temperature for the 1st heating period (Morning) .
4) Press or key to adjust the start time for period .
The time will change in 15 minute increments .
5) Press FAN to select Auto or Prog .
6) After you have set the time and the temperature for the
period to begin, press Set Schedule to advance to the
next program period .
7) Repeat steps 2 through 6 until all of the program times
and temperatures are set for all program periods on
that day .
8) Press "Advance Day" to change to the next day and
repeat steps 2 through 8 .
9) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
Run Schedule . The thermostat will now run your program .
8

Enter the Cooling Program

1) Press the SYSTEM button until the Cool icon appears .
2) Follow Enter Heating Program instructions for entering
cooling times and temperatures .
Automatic Schedule
This feature provides a method to program every day with the
most popular time and temperature settings using one key .
For this feature to be available, the Auto Schedule options
(Installer/Configuration menu item 17, AS Heat, or item 18,
AS Cool) must be selected On .
To use Auto Schedule, press Run Schedule to be sure you
are in normal operating mode . In SYSTEM Heat mode, use
the or keys to select your "Comfort Temperature" .
When your "Comfort Temperature" is selected, press Auto
Schedule key. The key will begin to flash indicating that the
feature is ready to store your selected temperature . Press
Auto Schedule a second time to complete the process . The
Auto Schedule key will disappear to indicate that the Auto
Schedule command has been accepted .
In Heat mode the thermostat will maintain your "Comfort Tem-
perature" during the Morning, Day and Evening periods and
setback 6° for the Night . Morning period will begin at 6:30 AM
and Night period will begin at 10:30 PM .
To set the Auto Schedule temperature for Cool mode, press
SYSTEM to change the mode to Cool and repeat setting the
temperature . In Cool mode, the thermostat will maintain your
selected "Comfort Temperature" continuously .
The "Comfort Temperature" can be temporarily overridden by
changing the setpoint temperature using the
Once Auto Schedule has been set and the key has disap-
peared, it can be reset in the Installer/ Configuration menu.
Entering Fan Program
In the Set Schedule mode, the FAN key is used to select the
fan operation during a program period . The default state of
the Fan key is FAN Auto (fan runs during a call for cool but
not on a call for heat) . It can be changed to FAN Prog (fan
runs during a program period) . Each press of the FAN key will
change the mode of the fan between Auto and Prog .
In the Run mode, when a program period that has FAN Prog
begins, the fan will turn on and stay on during the com-
plete period . The display will show FAN On Prog . Pressing
the FAN key will change FAN On Prog to On (fan running
continuously) or Auto . To return to FAN On Prog, press Run
Schedule .
or keys .