Image Quality - Panasonic WV-SFV531 Operating Instructions Manual

64kbps/ 128kbps*/ 256kbps*/ 384kbps*/ 512kbps*/ 768kbps*/ 1024kbps*/ 1536kbps*/ 2048kbps*/ 3072kbps*/
4096kbps*/ 6144kbps*/ 8192kbps*/ 10240kbps*/ 12288kbps*/ 14336kbps*/ 16384kbps*/ 20480kbps*/
24576kbps*/ 30720kbps*/ 40960kbps*
•
Default:
–
H.264(1): 4096kbps*
–
H.264(2): 1536kbps*
–
H.264(3): 1024kbps*
–
H.264(4): 512kbps*
* The range of bit rates that can be configured for H.264 bit rates differs depending on the "Transmission
priority" and "Image capture size".
When "Constant bit rate", "Frame rate", "Advanced VBR", or "Best effort" is selected for "Transmission
priority"
•
160x120 and 160x90: 64kbps - 2048kbps*
•
QVGA, 400x300, VGA, 320x180, and 640x360: 64kbps - 4096kbps*
•
800x600: 128kbps* - 4096kbps*
•
1280x960 and 1280x720: 256kbps* - 8192kbps*
•
1920x1080 and 1600x1200: 512kbps* - 14336kbps*
•
1920x1080 (60fps) and 1280x720 (60fps): 1024kbps* - 24576kbps*
•
2048x1536: 1024kbps* - 24576kbps*
When "VBR" is selected for "Transmission priority"
•
160x120 and 160x90: 64kbps - 40960kbps*
•
QVGA, 400x300, VGA, 320x180, and 640x360: 64kbps - 40960kbps*
•
800x600: 128kbps* - 40960kbps*
•
1280x960 and 1280x720: 256kbps* - 40960kbps*
•
1920x1080 and 1600x1200: 512kbps* - 40960kbps*
•
1920x1080 (60fps) and 1280x720 (60fps): 1024kbps* - 40960kbps*
•
2048x1536: 1024kbps* - 40960kbps*
Note
•
The H.264 bit rate is restricted by "Bandwidth control(bit rate)" on the [Network] tab on the "Network"
page (®page 151). For this reason, the bit rate may be lower than the value when any value with an
asterisk (*) on the right is selected.

[Image quality]

Select the image quality of H.264 images from the following.
•
When "Transmission priority" is set to "Constant bit rate" or "Best effort": Low(Motion priority)/
Normal/ Fine(Image quality priority)
•
VBR: 0 Super fine/ 1 Fine/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Low
•
Default: Normal
Note
•
When "Constant bit rate", "Best effort", or "VBR" is selected for "Transmission priority", this setting is
available.
[Refresh interval]
Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images.
If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264
to diminish image distortions. However, the refresh interval may be longer than the set value.
0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s
•
Default: 1s
11 Configure the settings relating to images and audio [Image/Audio]
Operating Instructions 93