Advertisement
®
Locking
Screw
Burner
Air Shutter
Orifice
Hood
(Spud)
/
Oven
Burner
Tube
Lower
Oven
Baffle
.
_Air
Shutter
(Rqmovable)
.............
Waist-High
Burner
(Self Clean Models)
ZLower
Oven
Bottom
(Removable)
_'__
Air Shutter
17
Lock Screw
Air Shutter
-,_
Orifice
Hood
Fig: 18
d. Set the oven to bake at 350°F and observe the flame. If the flame is yellow in color, increase air shutter opening size. If the
flame is a distinct blue color, but lifting away from the burner; reduce the air shutter opening size.
e. Turn off oven and allow to cool before adjusting air shutter. To adjust, loosen lock-screw (3), reposition air shutter (2), and tighten
lock-screw (3) (See Fig. 16). Retest the burner by repeating step "d" above. When the burner flame is a distinct blue color
burning steady, the air shutter is adjusted correctly.
f.
Replace burner baffle and oven bottom.
1 &Air
Shutter-Broil
Burner
a. Observe the flame to determine if the broiler burner flame is properly adjusted. It should be steady with approximately
1" blue
cones and no yellow or orange flame tips (See Fig. 17).
b. If adjustment to the air shutter is necessary, locate the broiler burner air shutter (See Fig. 18), loosen shutter lock screw, and
adjust to obtain optimum flame. This wilt normally be completely open for LP/Propane gas. If the flame is yellow in color,
increase the air shutter opening size. If the flame is a distinct blue, but lifting away from the burner, reduce the air shutter
opening size. Tighten the shutter set screw.
11. Replace
Storage
Drawer
or Warmer
Drawer
(instructions
for warmer
drawer
if equipped):
a. Pull the bearing glides to the front of the chassis glide (See Fig. 19).
b. Align the glide on each side of the drawer with the glide slots on the range.
I
Fig 19
c.
Push the drawer into the range until levers "click" (approximately 2"). Pull the drawer
_._
Glide
open again to seat bearing glides into position. If you do not hear the levers "click"
or the bearing glides do not feet seated remove the drawer and repeat steps "a"
through "c". This will minimize possible damage to the bearing glides.
12.Installation
of New LP/Propane
Rating/Serial
Plate and Conversion
Label
a. Using the list on page 1, determine the Surface Burner Combination that applies to
the range after it has been converted and select the corresponding
Rating Plate
part number in the approprate language (English/French).
b. Use a pen or permanent marker to fill out the LP/Propane Rating/Serial plate. Include the date that the LP conversion was
performed and the service company or individual performing the conversion. See the sample label below
c.
Place new plate as close as possible to the existing Rating/Serial
plate on range (See the recommended
locations shown in Fig. 20).
Remove Storage Drawer (some models),
Panel or Warmer Drawer (if equipped)
d. Remove the lower storage or warmer drawer and install the Regulator
for access to Regulator
L.R Conversion Label in the location shown in figure 20.
:: ORIGINAL PATINGPLATEFOR MODEL AND SERIALNUMBER
Sample
- L,P. Rating/Serial
Plate
Rating/
Serial
Plate
V
i_/
i_iii_ii! :_ _i I:
Fig. 20
_
Pressure Regulator
|
location at rear of range
ESTE
C0NT,0L c E P".O R M TEO"
A
THIS CONTROL
ETE CONVERT|
HAS BEEN CONVERTED
HA SIDO CONVERTIDO
-O
R ETRE UTILISE
FORDSEWTH
PARAUSARSE
_' U _:.....
L R GAS
CON GAsLR
A vt:u uu_Az.:
.
' "
' "
DE PETROLE
LIQUEFIE
phl 316241200
{0811)
Sample
- Regulator
LP, Conversion
Label
Advertisement
