Advertisement
6. Reconnect
Gas and Electrical
Supply to Range.
Do not use a flame
to check
for gas leaks.
Leak testing of the appliance shall be conducted according to the Installation Instructions provided with the Range.
Checking
Manifold
Gas Pressure
If it should be necessary to check the manifold gas pressure, remove the burner cap and connect a manometer (water gauge) or other
pressure device to the top right front burner orifice.
Using a rubber hose with inside diameter of approximately
1/4," hold tubing down
tight over orifice.
Turn burner valve on. For an accurate pressure check, have at least two (2) other surface burners burning. Be sure
the gas supply (inlet) pressure is at least one inch above specified range manifold pressure. The gas supply pressure should never be
over 14" water column. When properly adjusted the manifold water column pressure is 10" for LP/Propane gas or 4" for Natural gas.
Pressure
Testing
Gas Supply
Piping
System
a. Disconnect the range and its individual shut-off valve from the gas supply piping system during any pressure testing of that
system at test pressures greater than 14" of water column pressure (approximately
1/2" psig).
b. Isolate the range from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing
of the gas supply piping system at test pressures equal to or less than 14" of
water column pressure (approximately
1/2" psig).
7. Test surface
burners
to verify
if "LOW"
setting
should
be adjusted:
_,
a. Push in and turn control to LITE until burner ignites.
To
b. Push in and _
turn knob to LOWEST POSITION.
Surface
Burner
c.
If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. Insert a thin-bladed screwdriver into the hollow valve stem and engage the
_I_L'_
slotted screw inside. Flame size can be increased or decreased with the turn
Figl t2
of the screw. Turn counterclockwise
to increase flame size. Turn clockwise to
decrease flame size. (See Figs. 12).
Adjust flame until you can quickly turn knob from LITE to LOWEST POSITION without
extinguishing the flame. Flame should be as small as possible without going out.
NOTE: For Twin Burner Valve Adjustments
follow the instructions on
page 5.
i_
8. Adjust
the "LOW"
Setting
of the Twin Burner
Surface
Valve
(Figure
13)
(some
models).
On the Twin burner surface valve the low setting of each portion (inner portion and outer
portion of the twin burner) should be adjusted individually.
a. Push in and turn control to ignite the burner
b. Quickly turn knob to LOWEST POSITION.
Fig. 13
c.
If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. The inner portion of the twin burner flame size can be increased or decreased with the turn of the screw A. Use screw B to adjust
the flame size of the outer portion of the twin burner. Turn counterclockwise
the screw to increase flame size. Turn clockwise the
screw to decrease flame size. Adjust flame until you can quickly turn
knob from LITE to LOWEST POSITION without extinguishing
the flame,
Flame should be as small as possible without going out,
Note: Air mixture
adjustment
is not required
on surface
burners.
9. Air Shutter-Oven
Burner
The air shutter for the oven burner may need adjustment, especially if the
unit has been converted for use with LP/Propane gas. The approximate flame
length of the oven burner is 1 inch (distinct inner, blue flame) (See Fig. 14).
To determine if the oven burner flame is proper:
a. To access the air shutter you must remove the storage drawer or warmer
drawer (see removal instructions on page 2).
b. Remove the oven bottom by removing the screws at rear of oven
bottom. Lift up the rear of oven bottom and slide toward back of range to
disengage from front of oven front frame.
c.
Remove burner baffle by removing nut located on top of baffle and two
screws from front edge of oven front frame. Lift baffle straight up and out
of the oven.
Burner Flame Size
Figl 14
5/8.
Main
Top
1" Flame
Fig.
Advertisement
