Advertisement
Available languages
Available languages
IMPORTANT:
Observe all governing codes and ordinances.
Do
not obstruct flow of combustion
and ventilation air.
•
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located behind the control panel
and may be rotated up from behind the control panel for
viewing from the front of the range.
•
The range should be located for convenient use in the
kitchen.
Product Dimensions
B*
Recessed installations must provide complete enclosure of
the sides and rear of the range.
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
or microwave hood combination
that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
All openings in the wall or floor where range is to be installed
must be sealed.
Do not seal the range to the side cabinets.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see "Install Anti-Tip Bracket"
section.
F
•
Grounded electrical supply is required. See "Electrical
Requirements"
section.
•
Proper gas supply connection must be available. See "Gas
Supply Requirements"
section.
•
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
•
Use an insulated pad or 1¼.(0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance
with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures
of 194°F (90°C).
Mobile Home - Additional
Installation
Requirements
The installation of this range must conform to the Manufactured
Home Construction
and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured
Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest
edition, or with local
codes.
Mobile home installations require:
•
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
A. 35_"
+__" (90.8 + 0.3 cm)
cooktop height (minimum)
with leveling legs screwed all
the way in**
B. Model/serial/rating
plates
(located behind the control
panel)*
C. 47_" + _" (119.7 + 0.3 cm)
overall height (minimum) with
leveling legs screwed all the
way in**
D. 28½"+_ ¼"(72.4+_0.6cm)
depth with handle
E. 26_"
+ _" (66.4 + 0.3 cm)***
F. 291_ '' +__" (76.0 +_ 0.2 cm)
width
*Model/serial/rating
plates may be rotated up from behind the
control panel for viewing from the front of the range.
**Range can be raised approximately
1" (2.5 cm) by adjusting
the leveling legs.
***Excludes handle. Dimension given is from wall to front of oven
door and will vary based on electric outlet receptacle
installation.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT:
If installing a range hood or microwave hood
combination
above the range, follow the range hood or
microwave hood combination
installation instructions
for
dimensional clearances above the cooktop surface.
Range may be installed with zero clearance to combustible
construction
at the rear and on the sides below the cooktop.
•
Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See "Electrical Connection
- U.S.A. Only" section.
Advertisement
