Setting Up The System; Remote Control Unit (Rc-917) - Denon AVR-1803 Operating Instructions Manual

ENGLISH

10 SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in "CONNECTIONS" (see
pages 5 to 9), make the various settings described below on the display.
These settings are required to set up the listening room's AV system centered around the this unit.
1
Set the slide switch to "AUDIO".
2 Use the following buttons to set up the system:
• System setup items and default values (set upon shipment from the factory)
System setup
Input the combination of speakers in your system and
their corresponding sizes (SMALL for regular speakers,
Speaker
LARGE for full-size, full-range) to automatically set the
Configuration
composition of the signals output from the speakers and
the frequency response.
Subwoofer This selects the subwoofer speaker for playing deep bass
Mode signals.
Crossover Set the frequency (Hz) below which the bass sound of
Frequency the various speakers is to be output from the subwoofer.
This parameter is for optimizing the timing with which
Delay Time the audio signals are produced from the speakers and
subwoofer according to the listening position.
Digital In This assigns the digital input jacks for the
Assignment different input sources.
This assigns the component video input
Video In
jacks for the different video input
Assignment
sources.
Auto Surround
Auto surround mode function setting.
Mode
Ext. In SW
Set the Ext. In Subwoofer channel playback level.
Level
NOTE:
• The system setup is not displayed when "HEADPHONE ONLY" is selected.
10
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (•, ª, 0, 1)
Press this change what appears on the display.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
Default settings
Surround Back
Front Sp. Center Sp. Surround Sp.
Large Small Small
Subwoofer mode = Normal
80 Hz
Front & Subwoofer Center Surround L & R
3.6 m 3.6 m 3.0 m
Digital
COAXIAL OPTICAL 1 OPTICAL 2 OFF
Inputs
Input source
CD DVD/VDP TV/DBS VCR-1
Component
VIDEO 1 VIDEO 2 OFF OFF
Inputs
Input source DVD/VDP TV/DBS VCR-1 VCR-2
Auto Surround Mode = ON
Ext. In SW Level = +15 dB
Before setting up the system
1
(Main unit)
2
3
NOTE:
Press the SYSTEM SETUP button again to finish system set up. System set up can be finished at any time. The
changes to the settings made up to that point are entered.
Setting the speaker configuration
1
Subwoofer
Sp.
Small Yes
Surround back
2
3.0 m
OFF OPTICAL 3
VCR-2 CDR/TAPE
OFF –
NOTE:
• When "Small" has been selected for the front speakers, "Large" cannot be selected for the center speaker.
V. AUX –
Check that all the components are correct, then press the POWER operation
switch on the main unit to turn on the power.
Press the SYSTEM SETUP button to enter the setting.
*SYSTEM SET UP
NOTE: Please make sure the "AUDIO" position of the slide switch on the
remote control unit.
Press the ENTER or (down) button to switch to the speaker
configuration set up.
Use the (left) and (right) buttons to select your front speaker type.
(Initial)
LARGE
1 FRONT LARGE
(left) button
Press the ENTER or (down) button to switch to the center speaker setting.
Use the (left) and (right) buttons to select your center speaker type.
LARGE SMALL
2 CENTER SMALL
(left) button
Press the ENTER or (down) button to switch to the surround speaker setting.
SMALL
(right) button
(Initial)
NONE
(right) button