Using The Remote Control Unit; Setting Up The System - Denon AVR-1705 Operating Instructions Manual

ENGLISH
9

USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.
Range of operation of the remote control unit
30°
30°
Approx. 7 m
Inserting the batteries
q Press as shown by the arrow w Insert the R6P/AA batteries properly,
and slide off. as shown on the diagram.
NOTES:
• Use only R6P/AA batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside the battery compartment.)
• Remove the batteries if the remote control transmitter will not be used for an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact
with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the
time comes.
• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when
the remote control unit is operated nearby the set. (The included battery is only for verifying operation. Replace
it with a new battery as soon as possible.)
10
Point the remote control unit at the remote control
sensor as shown on the diagram at the left.
NOTES:
• The remote control unit can be used from a straight
distance of approximately 7 meters, but this distance
will shorten or operation will become difficult if
there are obstacles between the remote control unit
and the remote control sensor, if the remote control
sensor is exposed to direct sunlight or other strong
light, or if operated from an angle.
• Neon signs or other devices emitting pulse-type
noise nearby may result in malfunction, so keep the
set as far away from such devices as possible.
e Close the lid.
10

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in "CONNECTIONS" (see
pages 6 to 9), make the various settings described below on the display.
These settings are required to set up the listening room's AV system centered around the this unit.
1
Set the slide switch to "AUDIO".
2
Use the following buttons to set up the system:
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (•, ª, 0, 1)
Press this change what appears on the display.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
• System setup items and default values (set upon shipment from the factory)
System setup
Input the combination of speakers in your
system and their corresponding sizes (SMALL
Speaker for regular speakers, LARGE for full-size, full-
Configuration range) to automatically set the composition of
the signals output from the speakers and the
frequency response.
This parameter is for optimizing the timing with
which the audio signals are produced from the
Delay Time
speakers and subwoofer according to the
listening position.
Subwoofer This selects the subwoofer speaker for playing
Mode deep bass signals.
Set the frequency (Hz) below which the bass
Crossover
sound of the various speakers is to be output
Frequency
from the subwoofer.
This adjusts the volume of the signals output
from the speakers and subwoofer for the
Test Tone
different channels in order to obtain optimum
effects.
Digital In This assigns the digital input jacks
Assignment for the different input sources.
Auto Surround
Auto surround mode function setting.
Mode
Ext. In SW
Set the Ext. In Subwoofer channel playback level.
Level
NOTE:
• The system setup is not displayed when "HEADPHONE ONLY" is selected.
Default settings
Center Surround Surround
Front Sp.
Sp. Sp. Back Sp.
Large Small Small Small
Front Front Surround Surround Surround
Center
L R L R Back
3.6 m 3.6 m 3.6 m 3.0 m 3.0 m 3.0 m
Subwoofer mode = Normal
80 Hz
Front Front Surround Surround Surround
Center
L R L R Back
0 dB 0 dB 0 dB 0 dB 0 dB 0 dB
Input
COAXIAL OPTICAL 1 OPTICAL 2
source
Digital
CD DVD/VDP TV/DBS
Inputs
Auto Surround Mode = ON
Ext. In SW Level = +15 dB
Subwoofer
Yes
Subwoofer
3.6 m
Subwoofer
0 dB