About The Crossover; Source Setup; Source Setup Operation; Source Layout Setting - Alpine X009E Owner's Manual

About the Crossover

Crossover (X-OVER):
This unit is equipped with an active crossover. The crossover limits the
frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the frequencies
for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter)
of each band, and also the slope (how fast the filter rolls off the highs or
lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point, please
consult your authorized Alpine dealer.
Cut-off frequency
(1/3 octave steps)
HPF LPF
20 Hz -
Low range
----
speaker 200 Hz
Rear high
20 Hz -
----
range
200 Hz
speaker
Front high
20 Hz -
----
range
200 Hz
speaker
Low range
(Different from actual display)
Level adjusting
Output frequency range
(0 to –12 dB)
20 Hz
HPF cut-off
frequency
• HPF (high pass filter): Cuts the lower frequencies and allows the
higher frequencies to pass.
• LPF (low pass filter): Cuts the higher frequencies and allows the
lower frequencies to pass.
• Slope: The level change (in dB) for a frequency change of one octave.
• The higher the slope value, the steeper the slope becomes.
• Adjust the slope to FLAT to bypass the HP or LP filters.
• Do not use a tweeter without the HPF on or set to a low frequency, as
it may cause damage to the speaker due to the low frequency content.
• You cannot adjust the crossover frequency higher than the HPF or
lower than the LPF.
• Adjustment should be made according to the recommended crossover
frequency of the connected speakers. Determine the recommended
crossover frequency of the speakers. Adjusting to a frequency range
outside that recommended may cause damage to the speakers.
For the recommended crossover frequencies of Alpine speakers, refer
to the respective Owner's Manual.
We are not responsible for damage or malfunction of speakers caused
by using the crossover outside the recommended value.
48
-EN
Slope
HPF LPF
FLAT, –6,
---- –12, –18,
–12 dB
–24 dB/oct.
FLAT, –6,
–12, –18, ----
–12 dB
–24 dB/oct.
FLAT, –6,
–12, –18, ----
–12 dB
–24 dB/oct.
High range
Slope FLAT
Slope adjusting
(Different from actual display)
LPF cut-off
frequency

Source Setup

Source Setup Operation

The following steps 1 to 5 are common operations to each
"Setting item" of Source Setup. Refer to each section for details.
1
Touch [Setup] icon of Top banner.
The Setup main screen is displayed.
2
Touch [
The Source Setup screen appears.
3
Select the desired item.
Level
0 to
0 to
0 to
Setting items: Source Layout / Disc / AUX / RSE / TuneIt
4
Touch [
• When the pop-up window for setup is displayed, touch [
close the window after setting.
5
Touch [
• Immediately after changing the Source Setup (while the system is
writing data automatically) do not turn the ignition key to OFF.
Otherwise, the settings may not be changed.

Source Layout Setting

[Source Layout] is selected on the Source setup menu in step 3.
Refer to "Source Setup Operation" (page 48).

Setting the Slide Source Change

You can set whether to switch sources by swiping from the designated
area of the Audio/Visual Playback screen from right to left or from left
to right. Refer to "Switching Sources" (page 27).
Setting item: Slide Source Change
Setting contents: On (Initial setting) / Off
On: Source is changed by a swipe gesture.
Off: Source is not changed by a swipe gesture.
(Source)].
] or [ ] etc., to change its setting.
] to return to the previous screen.
] to