3. TECHNICAL BRIEF 3. TECHNICAL BRIEF 3.1 General Description The TU550 supports UMTS-850, UMTS-1900, GSM-850, GSM-900, DCS-1800, and PCS-1900 based GSM/GPRS/EDGE/UMTS/HSDPA. All receivers and the UMTS transmitter use the radioOne Zero-IF architecture to eliminate intermediate frequencies, directly converting signals between RF and baseband.
3. TECHNICAL BRIEF A generic, high-level functional block diagram of TU550 is shown in Figure 3-1. One antenna collects base station forward link signals and radiates handset reverse link signals. The antenna connects with receive and transmit paths through a switch module (plus two duplexers for UMTS high-band and low-band operations).
GSM900, DCS and PCS). The antenna switch module allows multiple operating bands and modes to share the same antenna. In TU550, a common antenna connects to one of eight paths: 1) UMTS-850 Rx/Tx, 2) UMTS-1900 Rx/Tx, 3) GSM-850 Rx, 4) GSM-900 Rx, 5) GSM-850 GSM-900 Tx, (Low Band Tx’s share the same path) 6) DCS-1800 Rx, and 7) DCS-1800,PCS-1900...
The RTR6200 UMTS output is routed to its power amplifier through a bandpass filter, and delivers fairly high-level signals that are filtered and applied to the PA. The PA device used in TU550 is “Load Insensitive PA”- no need to use isolator - and routed to the duplexer Tx port directly. Transmit power is delivered from the duplexer to the antenna through the switch module.
AC-couple the inactive pin to ground using an appropriately valued capacitor (12 pF is used in TU550). The 27 pF capacitor should be used to AC-couple the active pin to the VCO signal. Using only the selected VCO signal, the RFR6202 IC LO generation and distribution circuits create the necessary LO signals for the active quadrature downconverter.
-. Insertion loss . this component is also in the receive and transmit paths ; In the TU550 typical losses : UMTS1900_ Tx = 2.1 dB, UMTS1900_ Rx = 2.8 dB and UMTS850_ Tx =1.9 dB, UMTS850_ Rx = 2.7 dB -.
Its detector coupling range and converted voltage is based on diode sensitivity and transmitter power level. The TU550 uses National Semiconductor LMV232TLX power detector IC. In Figure 3.5.5-1, RF input power range of the device has been optimized for use with a 20dB directional coupler, without the need for additional external componets.
Figure. Schematic of USB block(MSM6275 Side & PM6650 Side) TU550 have a protective circuit for booting from USB. When the phone is booting from USB_VBUS without Battery, booting current is insufficient. Sometimes that can break the USB port of a computer.
3. TECHNICAL BRIEF 3.11.8 LCD Module (IM200CST4B : LG Innotek) - The IM200CST4B model is a Color TFT(Main & Sub) LCD supplied by LG Innotek. This main Module has a 2.0 inch diagonally measured active display area with 176(RGB)X220 resolution and sub Module has a 1.17 inch diagonally measured active display area with 96(RGB)X96 resolution.
4. TROUBLE SHOOTING 4.9 USB Troubleshooting USB Initial sequence of TU550 is : USB connected to TU550 power on → USB_VBUS(Q501) go to 5V → USB_D+ go to 3.3V 48M Crystal on → USB_VP and USB_VN is triggered → USB work. Start...
LGMDP supports Windows 2000/XP where the LG (Ver 4.6 or later) USB modem driver is installed. Additionally, LGMDP allows multi downloading up to 8 handsets at the same time.