1. Manuals
  2. Brands
  3. Lowrance Manuals
  4. GPS
  5. GlobalMap 5300C iGPS
  6. Operation instructions manual

Lowrance 5300c iGPS Operation Instructions Manual

Mapping gps receiver
Hide thumbs Also See for 5300c iGPS:
Table of Contents

Advertisement

Quick Links

Download this manual
Pub. 988-0152-191
www.lowrance.com
®
GlobalMap
5300c iGPS
Mapping GPS Receiver

Operation Instructions

www.Busse-Yachtshop.de
email: info@busse-yachtshop.de

Advertisement

Table of Contents
loading

Related Manuals for Lowrance 5300c iGPS

Summary of Contents for Lowrance 5300c iGPS

  • Page 1: Operation Instructions

    Pub. 988-0152-191 www.lowrance.com ® GlobalMap 5300c iGPS Mapping GPS Receiver Operation Instructions www.Busse-Yachtshop.de email: info@busse-yachtshop.de...
  • Page 2 We reserve the right to do so without notice. All features and specifications subject to change without notice. On the cover: GlobalMap 5300c iGPS. All screens in this manual are simulated. For free owner's manuals and the most current information on this product, its operation and accessories, www.Busse-Yachtshop.de...

  • Page 3: Table Of Contents

    Navigate Back to MOB Waypoint ... 47 Navigate to Cursor Position on Map... 48 Navigate to a Point of Interest ... 49 Creating and Saving a Trail ... 50 www.Busse-Yachtshop.de Table of Contents ® 5300c iGPS ... 2 email: info@busse-yachtshop.de...
  • Page 4 Displaying a Saved Trail ... 51 Navigating Trails ... 52 Transfer Custom Maps and GPS Data Files ... 56 Cancel Navigation ... 58 Section 4: Advanced Operations ... 59 Find Distance from different Locations... 59 Find Distance from Point to Point ... 59 Icons ...
  • Page 5 Find Streets or Intersections... 118 Find Waypoints ... 121 Section 7: NMEA 2000 ... 125 NMEA 2000 Menu... 125 Internal GPS Receiver ... 125 Bus Setup... 126 Engine & Tank Configuration... 127 Tank Select ... 127 Tank Size ... 128 Set Configuration button ...
  • Page 6 Device Configuration Menu... 129 Device Information and Device Data ... 129 Fuel Management Menu... 130 Tank Location ... 130 Fuel Added ... 130 Add Fuel... 130 Fill Tank... 131 Adding Fuel to Tank ... 131 Engine Operations... 131 Engine Select ... 131 NMEA 2000 Alarms ...
  • Page 7 NOTICE! The storage and operation temperature range for your unit is from -20 degrees to +167 degrees Fahrenheit (-28 degrees to +75 degrees Cel- sius). Extended storage or operation in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty.
  • Page 8 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...

  • Page 9: Section 1: Read Me First

    Section 3 covers Basic GPS Operation. It will show you how easy it is to run the GlobalMap 5300c, right out of the box. This section features a one-page GPS Quick Reference. (If you've already jumped ahead...

  • Page 10: Specifications: Globalmap ® 5300C Igps

    GPS options in Section 5, System Setup and GPS Setup Options. In Section 6, we go into more detail on one of the GlobalMap 5300c's most remarkable capabilities — Searching. We'll introduce a search example in the Basic GPS Operation section, but there are so many...
  • Page 11 Zoom range: ...39 ranges; 0.02 to 4,000 miles. NOTE: The above memory capacities refer only to the GlobalMap 5300c's on- board memory. The amount of GPS data you can record and save for recall later is limited only by the number of MMC cards you have.

  • Page 12: How Lowrance Gps Works

    How Lowrance GPS Works You'll navigate faster and easier if you understand how the GlobalMap 5300c scans the sky to tell you where you are on the earth — and, where you're going. (But if you already have a working understanding of GPS receivers and the GPS navigation system, skip on ahead to Sec- tion 2, Installation &...

  • Page 13: Introduction To Gps And Waas

    Section 2, Installation & Accessories, on page 11, so you can mount your GlobalMap 5300c and plug in the power. Or you might want to see how our text formatting makes the manual tuto- rials easy to skim.
  • Page 14 It relies solely on the signals from the satel- lites to calculate a position. Speed, direction of travel, and distance are all calculated from position information. Therefore, in order for the GlobalMap 5300c to determine direction of travel, you must be moving and the faster, the better. www.Busse-Yachtshop.de...

  • Page 15: Free Training Aids Available

    WAAS signal from ground receivers. You'll find that using your GPS receiver is both easy and amazingly accurate. It’s easily the most accurate method of electronic navigation available to the general public today. Remember that this receiver is only a tool.

  • Page 16: How To Use This Manual: Typographical Conventions

    If you or a friend has Internet access, visit our web site. Find us at . The site is packed with additional information WWW.LOWRANCE.COM on using our products. Emulator For the ultimate training aid, be sure to download the free emulator software for your unit.
  • Page 17 2. Press ↓ to Trail 1| 3. You are asked to wait while it converts the trail into a route. 4. The wait message disappears and the GlobalMap 5300c begins showing navigation information along the trail. Now, begin moving and follow your GlobalMap 5300c.
  • Page 18 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...

  • Page 19: Section 2: Installation

    Section 2: Installation Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1.

  • Page 20: Powering Your Display Unit

    To unit The Power/Data cable for this unit. NOTE: There are two basic power connection options, which are shown in the following two diagrams. Read the following instructions carefully to determine which power connection applies to your unit. Depending on your configuration, you may not use all of these wires.
  • Page 21 interference, or if such a switch is not available, we recommend connecting direct to the battery and installing an in-line switch. This will let you shut off power to the power cable when the unit is not in use. When you are not using the unit, you should always shut off power to the power cable, especially when the power cable is disconnected from the unit.

  • Page 22: Power Diagram A

    To unit Display Unit Power Cable Recommended display unit power-off switch Data Cable Use this method if you are powering the display unit and a GPS mod- ule or the display unit and a NMEA 2000 network. (Fuses may be dif- The network and any NMEA 2000 devices, including the GPS module, will not operate unless the NMEA 2000 Power Cable is connected to power.

  • Page 23: Power Diagram B

    To unit All unused Data or NMEA 2000 power wires should be capped with wire nuts and electrical tape to prevent shorts. Data Cable NMEA 2000 Power Cable Use this method if you are only powering your display unit and are not powering a NMEA 2000 network or any NMEA 2000 accessory device, including a GPS module.

  • Page 24: Connecting To A Nmea 2000 Network

    NMEA 0183 Wiring (Data cable) To exchange NMEA 0183 data, the GlobalMap 5300c has one NMEA 0183 version 2.0 communication port. Com port one (Com-1) can be used to receive NMEA format GPS data. The com port can also trans- mit NMEA format GPS data to another device.
  • Page 25 Orange (Receive) NMEA Transmit To Other Com-1 GPS Receiver To GlobalMap Shield (Ground) Ground 5300c Com-1 wiring to receive NMEA position information from some other GPS receiver Yellow (Transmit) NMEA Receive Com-1 To Other To GlobalMap Shield (Ground) Ground Device...

  • Page 26: Mounting The Unit: Bracket Or Portable

    GlobalMap 5300c iGPS Cable Connections. Mounting the Unit: Bracket or Portable You can install the GlobalMap 5300c on the top of a dash with the sup- plied gimbal bracket. It can also be mounted on a portable power supply. If you use the supplied bracket, you may be interested in the optional ®...

  • Page 27: Bracket Installation

    Sonar or Map page for normal operation Make sure there is enough room behind the GlobalMap 5300c to attach the power cable. (A drawing on the next page shows the dimensions of a gim- bal-mounted GlobalMap 5300c.)
  • Page 28 [5.43] Millimeter [Inch] Front view (left) and side view (right) showing dimensions of the GlobalMap 5300c when mounted on gimbal bracket. After drilling the hole, pass the power cable's bare-wire end down though the hole from the top. www.Busse-Yachtshop.de ward the front of your unit.

  • Page 29: Portable Installation

    GlobalMap 5300c. If you choose to fill in the hole, be sure to position the cables against the rear edge of the hole as you apply the fill material.

  • Page 30: Mmc Or Sd Card Memory Card Installation

    MMC or SD Card Memory Card Installation Your GlobalMap 5300c uses a MultiMedia Card to store information, such as custom maps, waypoints, trails and other GPS data. The unit can also use Secure Digital Cards (SD card) to store data.

  • Page 31: Other Accessories

    To add an MMC or SD Card 1. Open the card compartment door. 2. Grasp the bottom of the MMC and push the top of the card into the slot. Once the card is started, use your fingernails to slide it the rest of the way to the left, until it is firmly seated in the slot.

  • Page 32: Face Cover

    This includes towing a boat on a trailer at highway speeds. Otherwise, wind blast can pop off the cover. Now that you have your GlobalMap 5300c installed, move on to Section 3, Basic GPS Operations. There, we'll present a series of step-by-step tutorials to teach you the basics of GPS navigation.

  • Page 33: Section 3: Basic Gps Operation

    Quick Reference on page 40. Keyboard MMC slot access door GlobalMap 5300c GPS unit, front view, showing Map Page, keyboard and access door for the MMC slot. 1. PWR/LIGHT (Power & Light) – The PWR key turns the unit on and off and activates the backlight.

  • Page 34: Power/Lights On And Off

    2. PAGES – Pressing this and the ← → arrow keys (4) switches the unit between the three different page screens. (Satellite Status Page, Navigation Page and Map Page.) Each page represents one of the unit's major operation modes. 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature.
  • Page 35 Cancel Navigation: cancels navigation commands. Used to stop navi- gating after you reach your destination. GPS Setup: sets various GPS receiver options. System Setup: sets general configuration options. NMEA 2000: provides access to all NMEA 2000 network setup options, including the configuration of devices on the network.

  • Page 36: Satellite Status Page

    Browse MMC Files: this allows you to view the installed MMC card and the files it contains. Pages The unit has three Pages that represent the three major operating modes. They are the Satellite Status Page, the Navigation Page and the Map Page.
  • Page 37 North is at the top of the screen. You can use this to see which satellites are obstructed by obstacles in your immediate area if the unit is facing north. The GPS receiver will track satellites that are in bold type. The re- ceiver hasn't locked onto a satellite if the number is grayed out, there- fore it isn't being used to calculate your position.

  • Page 38: Navigation Page

    5. Select the desired subcategory and press checkmark in the checkbox, showing the selected data is set for display. 6. If you want to display other data types, repeat Steps 4 and 5. Press repeatedly to get back to the Custom Gauges page. The data you EXIT selected will now be displayed on the screen.
  • Page 39 Track or compass heading indicator, showing direction of travel Navigation information displays in customizable data boxes Trail line Navigation Page, recording a trail, traveling southwest. Page looks like this when the unit is not navigating to a waypoint, following a route, or backtracking a trail. When navigating to a waypoint, the Navigation screen looks like the following figure.
  • Page 40 Left cross track error line Current track or heading, shown in degrees Compass bearing to destination Trail line Navigation information displays in data boxes Navigation Page, going to a waypoint while creating a new trail. The cross track error range is shown on the compass rose as a wide, white, corridor enclosing the course line.

  • Page 41: Map Page

    The Navigation Page has its own menu, which is used for some ad- vanced functions and for setting various options. (Options and setup are discussed in Sec. 5). To access the Navigation Page Menu, from the Navigation Page, press MENU Map Page The Map Page screens show your course and track from a bird's-eye view.

  • Page 42: Background Map Vs. Mapcreate Map Content

    If you're using only the factory-loaded background map, the maximum zoom range for showing additional map detail is 20 miles. You can con- tinue to zoom in closer, but the map will simply be enlarged without revealing more map content (except for a few major city streets.) Load your own high-detail custom map made with MapCreate (or a pre-made FreedomMap from LEI), and you can zoom in to 0.02 miles with mas- sive amounts of accurate map detail.
  • Page 43 background map would show you the general outline and approximate shape of a coastline or water body, but the higher detail in MapCreate shows the shoreline completely and accurately (finer detail). Many smaller islands would not be included in the background map, but are in MapCreate.
  • Page 44 The Map Page has its own menu, which is used for several functions and for setting various options. To access map display options, press highlight , then select the desired map page option. Press PAGES EXIT Digital Data map page (left). Two Position Formats page (right). In pages that have two major windows (such as two maps) you can tog- back forth...

  • Page 45: Map With Custom Gauges

    1. From any two-window display, press |↓ to MENU ESIZE INDOW 2. Four flashing arrows appear along the centerline dividing the two windows. The windows will be in a horizontal position by default, so press ↑ ↓ to resize the windows. Or, if you want to realign the windows vertically, use ←...

  • Page 46: Radar

    5. Select the desired subcategory and press checkmark in the checkbox, showing the selected data is set for display. 6. If you want to display other data types, repeat Steps 4 and 5. Press repeatedly to get back to the Map with Custom Gauges page. The EXIT data you selected will now be displayed in the gray area on the left side of the screen.
  • Page 47 Radar Page (left) with Radar menu display (right). To access Radar Page: 1. Press , highlight the PAGES 2. Press to open the Radar menu. Press MENU dar display. The following page contains a 12-step quick reference for the most basic GPS operations.

  • Page 48: Basic Gps Quick Reference

    Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navi- gating to a location at least a few blocks away. Navigation in too small an area will constantly trigger arrival alarms. 1.

  • Page 49: Find Your Current Position

    Find Your Current Position Finding your current position is as simple as turning on the unit. With- out obstruction from dense foliage, terrain or structures, the unit auto- matically searches for satellites and calculates its position in approxi- mately one minute or less. If for some reason satellite acquisition takes longer, you may be inside a structure or vehicle or in terrain that is blocking signal reception.

  • Page 50: Selecting Any Map Item With The Cursor

    Cursor line Selected airport The selected airport to the northwest is 4.2 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2.
  • Page 51 2. You could search the entire restaurant category, but in this example we will narrow our search. Press → to |↓ to HAINS 3. The unit says it is calculating, then a list of restaurants appears, with the closest highlighted at the top of the list. The restaurant far- thest from you is at the bottom of the list.

  • Page 52: Set A Waypoint

    6. The unit's map appears, with the cursor crosshairss highlighting the restaurant's POI symbol. A pop-up data box shows the POI's name, dis- tance and bearing. A data box at the bottom of the screen continues to display the location's latitude and longitude. Map screen showing Finding Waypoint, the result of a restaurant search.
  • Page 53 To create and save a Waypoint: These first two techniques use the Quick Save method, the fastest and easiest way to create a waypoint. Create Waypoint at Current Position While you are traveling, press automatically given a name with a sequential number, such as "way- point 003."...

  • Page 54: Navigate To A Waypoint

    Symbol is described in Sec. 4.) After you have changed a waypoint symbol, the unit will remember the one you chose and use it the next time you save a waypoint. To revert back to the default sym- bol, edit a waypoint and choose the original symbol, or use the Re- set Options command (described in Sec.

  • Page 55: Set Man Overboard (Mob) Waypoint

    Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter. It's particularly dangerous at night or if you're out of sight of land. Of course, the first thing to do is remain calm and then use all standard safety procedures to rescue the person.

  • Page 56: Navigate To Cursor Position On Map

    Navigate to Cursor Position on Map command: navigates to the current cursor position on URSOR the map. It's a quick and handy way to navigate to anything you can see on the map display. 1. Use the cursor (controlled by the arrow keys) with the zoom in and zoom out keys to maneuver around the map until you find a location you want to go to.

  • Page 57: Navigate To A Point Of Interest

    The 15-mile zoom figure (left) clearly shows the dotted course line con- necting your current position to your destination. The 40-mile zoom (center) shows both current position and destination on screen. The Navigation Page (right) will also show navigation information. To stop navigating to the cursor, use the Cancel Navigation command: press |↓...

  • Page 58: Creating And Saving A Trail

    Creating and Saving a Trail A trail, or plot trail, is a string of position points plotted by the unit as you travel. It's a travel history, a record of the path you have taken. Trails are useful for repeating a journey along the same track. They are particularly handy when you are trying to retrace your trip and go back the way you came.

  • Page 59: Displaying A Saved Trail

    4. To return to the previous page, press the Edit Trail menu, you will notice that a new trail starts with a new sequential number. In the example figure below, the new trail is num- ber 2, showing zero points. Note that Trail 1 is inactive, but it is still visible on the map.

  • Page 60: Navigating Trails

    To turn off trail display: 1. Press MENU MENU 2. Press ↓ to enter the Saved Trail list, then use ↑ ↓ to select the de- sired Trail Name| 3. Press ↓ to |→ to CTIVE press repeatedly. EXIT To turn on trail display: 1.

  • Page 61: Navigate A Trail

    Tip: Generally, when using this method, the smaller the zoom range, the more accurately you will be able to steer along the trail. Navigate a Trail The following figures illustrate the menu sequence for navigating a trail. 1. Press MENU MENU 2.
  • Page 62 Figure 1. Figure 3. Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate command highlighted for Trail 6. A trail is always converted to a "route"...
  • Page 63 Track or compass heading indicator Trail waypoint symbol Course line made from trail Navigate trail, navigation page (compass rose) views: driver is northbound heading straight toward trail point 6 (left); bearing arrow shows the trail point is due north (straight ahead.) Driver has reached trail point 6 and must turn west to follow the trail (right).

  • Page 64: Transfer Custom Maps And Gps Data Files

    Transfer Custom Maps and GPS Data Files Custom Maps: Custom maps work only from the MMC card or SD card. When a card containing a Custom Map File is loaded into the unit, the unit auto- matically loads the map into memory when the unit is turned on. Instructions for copying Custom Map Files to an MMC are contained in the instruction manual for your MMC card reader and MapCreate soft- ware.
  • Page 65 2. The Transfer My Data menu includes a message which tells you if an MMC is present or not. If no MMC is present, you must first insert a card into the unit in order to activate the Load or Save commands. To transfer data from the unit to the MMC: press To transfer data from the MMC to the unit: press →...

  • Page 66: Cancel Navigation

    Figure 1. Figure 3. These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the navigation commands after you reach your destination or at any other time by using the Cancel Navigation com- mand.

  • Page 67: Section 4: Advanced Operations

    Section 4: Advanced Operations Find Distance from different Locations 1. While on the Map Page press: 2. Center your cursor over the position you want to find the distance to. A rubber band line appears, connecting your current position to the cursor's location.

  • Page 68: Create Icon On Map

    These are sometimes referred to as event marker icons. This unit has 63 different symbols you can pick from when creating an icon. Icons are similar to waypoints, but they do not store as much informa- tion (like names) as waypoints do. You can't use a menu to navigate to icons as you can with waypoints.

  • Page 69: Navigate To An Icon

    Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol menu. Press ← or ↑ or → or ↓ to select the icon symbol to delete, then press .

  • Page 70: Create And Save A Route

    waypoint. Once programmed into the GPS unit, a route provides the option of navigating forward through the route waypoints or in reverse order (you can even begin navigating in the middle of a route!) Create and Save a Route You have the option of creating and editing a route in the unit or you can make a route on your computer with our MapCreate software.
  • Page 71 Edit Route menu (left). Edit Route Waypoints menu (right) with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor until the cursor is centered on the spot where you want your route to begin. (If you are starting at your current position or the current cursor posi- tion, you are already at the starting spot.) 4.

  • Page 72: Delete A Route

    Route creation sequence, continued: Fig. 4. Point (3) set at on-ramp turn. Fig. 5. Waypoint (4) set at highway exit to frontage road leading to river. Waypoint (5) ends the route at a tree stand in the hunting area. Fig. 6. Press EXIT to save the route and you return to this screen. 5.

  • Page 73: Edit Route Waypoints

    2. Press ↓ to route name| 3. Press ↑ or ↓ to change the first character, then press → to move the cursor to the next character and repeat until the name is correct, then press . Return to the previous page by pressing Edit Route Waypoints You can edit the route by adding and removing waypoints.

  • Page 74: Navigate A Route

    Route Planning on Main Menu (left). Routes menu (center). Edit Route menu (right). Navigate is selected on Edit Route menu. Navigate a Route 1. From the AVIGATION press |↓ to MENU MENU 2. Press ↓ to select route name| 3. Upon arrival at your destination, cancel navigation: press |↓...

  • Page 75: Trails

    Figure 1. Figure 3. Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to the east.

  • Page 76: Edit A Trail Name

    Edit a Trail Name To edit a trail name: press name| . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. Press then repeatedly to return to the previous page display. EXIT Tip: You can quickly call up the Edit Trail menu by selecting a trail on...

  • Page 77: Utilities

    Edit Trail Menu with Pattern option selected (left). Edited trail with Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To access the unit's alarm clock: press LARM LOCK Sun/Moon Rise & Set Calculator To get to the Sun/Moon menu: press LATIONS Trip Calculator To get to the Calculator menu: press...

  • Page 78: Edit A Waypoint

    To delete a waypoint from the map: 1. Use the arrow keys to select the waypoint with the cursor. 2. Press |↓ to ELETE previous page and clear the cursor, press To delete all waypoints at one time: 1. Press MENU MENU |←...

  • Page 79: Set A Waypoint By Average Position

    Create Waypoint by Entering a Position 1. Press |→ to 2. Press ↓ to NTERED 3. Press → to ATITUDE change the first character, then press → to the next character and re- peat until the latitude is correct. Press New Waypoint screen (left).

  • Page 80: Set A Waypoint By Projecting A Position

    This boosts waypoint position accuracy by helping to eliminate errors caused by atmospheric conditions and other factors. 1. Press |→ to 2. Press ↓ or ↑ to VERAGE 3. Wait while the unit takes points to average for the position. (The greater the number of points, the greater the accuracy.) When the desired number of points accumulates, press 4.

  • Page 81: Section 5: System & Gps Setup

    Section 5: System & GPS Setup Alarms This unit has several GPS alarms. The factory default setting has all of these but the anchor alarm turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint.

  • Page 82: Auto Satellite Search

    Auto Satellite Search To lock on to the satellites, the GPS receiver needs to know its current position, UTC time and date. (Elevation [altitude] is also used in the equation, but it's rarely required to determine a position.) It needs this data so that it can calculate which satellites should be in view.

  • Page 83: Check Mmc Files And Storage Space

    MMC File Browser. Check MMC Files and Storage Space To check MMC Files: Press |↓ to MENU MENU MMC F ENT. ROWSE ILES Communications Port Configuration The unit has one NMEA 0183 version 2.0 compatible communication port, or com port for short. The Com Port Menu, which is accessed from the System Setup Menu, allows you to configure the communications port to send or receive data from another electronic device, such as an autopilot.

  • Page 84: Configure Nmea

    For connectors and wiring information for another device, see page 16. For assistance in configuring the unit to communicate with another device, consult the factory. Customer service phone numbers are in the back of this manual. Configure NMEA You can configure the unit to use specific NMEA sentences. 1.
  • Page 85 (Universal Transverse Mercator) projection; MGRS (Standard); MGRS (Standard + 10); Map Fix; Loran TD; British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan and Greek. UTM's are marked on USGS topographic charts. This system divides the Earth into 60 zones, each 6 degrees wide in longitude. British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan, and Greek grid systems are the national coordinate system used only in their respective countries.

  • Page 86: Map Fix

    Configure Loran TD menu. Map Fix Map Fix is used with charts or maps. This system asks for a reference position in latitude/longitude, which you take from a marked location on the map. It then shows the present position as distance on the map from that reference point.

  • Page 87: Customize Page Displays

    4. Press and enter the map's scale. This is generally at the bottom of the paper map. It is shown as a ratio, like 1:24000. Press the unit to return to the Configure Map Fix screen. Configure a map fix so the unit can find your position on a printed 5.

  • Page 88: Gps Simulator

    to change the box or hit ↑, ↓, ← → to select another box, then 2. Press press . You will see a list of categories with "+" or "–" symbols next to each category. A category with a "+" is expandable, meaning its contents are hidden.
  • Page 89 To turn on the GPS Simulator: 1. Press MENU MENU 2. Select and press IMULATORS The GPS Simulator page will appear. The page has dialog boxes that allow you to change the Track, Speed, Altitude, Latitude and Longitude of your simulation. You can begin your simulation at a waypoint by using the Select Start- ing Waypoint command or direct the simulation manually by using the Steer with Arrows command, which will place Steer with Arrow boxes...

  • Page 90: Initialize Gps

    Steer with Arrows When you are using the Steer with Arrows command, you can press to clear the steering and speed boxes from the screen while con- EXIT tinuing the simulation. This action will allow you to use the map cursor during a simulation.

  • Page 91: Map Auto Zoom

    Map Auto Zoom This unit has an auto zoom feature that eliminates much of the button pushing common with other brands of GPS receivers. It works in con- junction with the navigation features. First, start navigation to a waypoint. (See the waypoint section for more information on navigating to a waypoint.) Then, with the auto zoom mode on, the unit zooms out until the entire course shows, from the present position to the destination waypoint.
  • Page 92 To show Map Data 1. From the Map Page, press 2. Press to open the much detail you want — from Off (so the unit operates like a GPS plot- ter) to High. 3. After the option is set, press display.

  • Page 93: Map Datum Selection

    To turn on/off range rings: 1. From the Map Page, press 2. Press ↓, → to ANGE check it (turn on) and uncheck it (turn off.) 3. After the option is set, press To turn on/off Lat/Long Grid lines: 1. From the Map Page, press 2.

  • Page 94: Map Detail Category Selection

    Map Detail Category Selection This menu determines which of the mapping features are shown on the screen. This includes: waypoints, trails, icons, cities, highways, etc. You can turn on or off any of these items to customize the map. To get to Map Categories: 1.

  • Page 95: Nauticpath™ Usa Marine Charts

    In Track Up mode, map shows "N" and arrow to indicate north. Map page shown in North Up mode (left) Map page shown in Track Up To change map orientation: 1. From the Map Page, press 2. Use ↑ ↓ to select the desired mode, then press 3.

  • Page 96: Nautical Chart Notes

    Nautical Chart Notes NauticPath charts contain notes or chart information, represented by circle-i Chart Note icons on the map display. An example is shown in the following figure. NauticPath chart showing Chart Note icon selected by cursor (left). Note information screen (right). To view Chart Note information: 1.

  • Page 97: Tidal Current Information

    These icons will appear when you are zoomed in to a 4-nautical mile range. An example is displayed in the following figures. To view Port Services information: 1. Use the arrow keys to move the cursor over a Port Services icon. When it is selected, a pop-up name box appears.

  • Page 98: To View Tidal Current Information

    zoomed in to a 6-mile range. The icon stands for a Tidal Current Sta- tion location. An example is displayed on the right. When you zoom in to a sufficiently small zoom range (0.8 nautical mile), the icon becomes an animated arrow showing tidal current veloc- ity and direction for the selected tidal station at the present time.

  • Page 99: Tide Information

    The Tidal Current Information screen displays daily tidal current data for this station on this date at the present time. The graph at the top of the screen is an approximate view of the flood and ebb pattern for the day, from midnight (MN), to noon (NN) to midnight (MN).

  • Page 100: Navionics ® Charts

    To view tide information: 1. Use the arrow keys to move the cursor over a tide station icon. When it is selected, a pop-up name box appears. 2. Press to display the Tide Information screen. MLLW Line Tide Table The Tide Information screen displays daily tidal data for this station on this date at the present time.

  • Page 101: Overlay Data

    play. NauticPath charts are ready for display as soon as they are inserted into the unit. Navionics charts must be inserted into the unit, then selected as a Map Choice option in the Map Data menu. To display a Navionics chart: 1.
  • Page 102 Overlay Data with Navigation and Sonar Data categories expanded. To overlay information on your screen: 1. Press |↓ to MENU VERLAY 2. If you currently have any overlay data on your screen, it will be listed here. Select and press .
  • Page 103 Data Viewer (left). Navigation category expanded with Bearing and Distance selected (center). Bearing and Distance displayed on Overlay Steering arrow Map Page shows boat cruising Puget Sound, Washington with Overlay Data turned on (left). This example shows Depth, Ground Speed and the Steering Arrow.
  • Page 104 NOTE: You also can remove data directly from the Data Viewer menu by repeating the steps used to add overlay data. Highlight the overlay data currently displayed, then press tion, which will remove it from the display.. Overlay Data Shown menu with Date selected (left). Remove high- lighted on Data Information menu (center).

  • Page 105: Pop-Up Help

    Trip Distance set to small size in the Overlay Data Shown menu (left). Trip Distance set to Large size (right). To change displayed data font size: 1. From the Map or Sonar page, press 2. Press ↓ ↑ to select the desired data type, then use ← → to enlarge or reduce the size of the overlay data on the map display.

  • Page 106: Reset Options

    Pop-up Help command highlighted on System Setup menu (left). Pop- up Help message for Sounds (right). Reset Options The Reset Options command allows you to switch unit features and functions back to factory default settings. 1. Press MENU MENU NOTE: Reset Options does not erase any waypoints, routes, icons, plot trails or sonar logs.

  • Page 107: Screen Contrast And Brightness

    Screen Contrast and Brightness To adjust Contrast: 1. Press MENU MENU 2. Highlight ONTRAST bar. The left end of the scale is the lowest contrast level. The right end is the highest contrast level. The Screen Menu with Contrast bar selected. To adjust brightness: 1.

  • Page 108: Set Language

    To adjust the screen's display mode: 1. Press MENU MENU 2. Press ↓ to ISPLAY with three options: Normal, High Contrast and Night Viewing. 3. Select the desired mode and press the map display. Set Language This unit's menus are available in 10 languages: English, French, Ger- man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish.

  • Page 109: Show Waas Alarm

    To set the Year: 1. Make sure your unit has acquired your position, then press , highlight MENU MENU 2. Highlight OCAL 3. Select and press To select Time Format: 1. Make sure your unit has acquired your position, then press , highlight MENU MENU...

  • Page 110: Software Version Information

    To turn on/off the WAAS Alarm: 1. Press MENU MENU 2. With the option highlighted, press check it (turn off) the WAAS Alarm. 3. Press to return to the map display. EXIT EXIT To Require WAAS: 1. Press MENU MENU 2.
  • Page 111 To set Volume: 1. Press MENU MENU 2. Highlight and use ← → to move the Volume control bar. The OLUME left end of the scale is low volume. The right end of the scale is high vol- ume. 3. Press to return to map display.

  • Page 112: Track Smoothing

    Track Smoothing This is a factory setting on the GPS Setup menu that should always be left on. When stopped or traveling at slow speeds (such as walking or trolling), Track Smoothing prevents wandering of trails, the steering arrow, compass rose and a map in track-up mode. Trail Options There are several options you can use with trails.

  • Page 113: Update Trail Option

    New Trail selected on the Trails menu (left). Edit Trails menu (right). To Delete all Trails 1. Press MENU MENU 2. Highlight ELETE pear: Delete All Trails? 3. Select and press where all trails have been deleted. 4. Press repeatedly to return to the map display. EXIT Update Trail Option The Update Trail menu allows you to change the way trail updates oc-...
  • Page 114 To select a Trail Update Option: 1. Press MENU MENU 2. Highlight the RAIL menu will appear with three update criteria: Auto, Time and Distance. NOTE: The Update Active Trail checkbox should be checked (turned on). If it is unchecked (turned off), your trails will not be updated. To turn it on, highlight 3.

  • Page 115: Transparency

    Edit Trail menu. Trail Visible/Invisible and Other Trail Options The name, maximum number of points in the trail, activity, and visibil- ity are all changed on the Edit Trail menu screen. The Active setting determines whether or not the unit is recording new points for a par- ticular trail.

  • Page 116: Units Of Measure

    Transparency selected on main menu. Transparency slider bar (right). To adjust Transparency level: 1. Press MENU MENU bar appears. 2. Use ↑ ↓ to move the bar. Move the bar to the bottom of the scale to eliminate transparency. Moving the bar to the top of the scale will pro- vide the greatest level of transparency.
  • Page 117 To set Temperature units: 1. Press MENU MENU will be highlighted, so press 2. Highlight EMPERATURE 3. Use ↑ ↓ to select one of the following options: Fahrenheit, Celsius or Kelvin. Press 4. Press repeatedly to return to the sonar display. EXIT To set Pressure units: 1.
  • Page 118 3. Use ↑ ↓ to select one of the following options: Gallons or Liters. Press 4. Press repeatedly to return to the sonar display. EXIT To set Heading units: 1. Press MENU MENU will be highlighted, so press 2. Highlight and press EADING 3.

  • Page 119: Section 6: Searching

    Section 6: Searching NOTE: The background map loaded in your unit's permanent memory lets you search for some land features, including cities and lakes. For a full set of searchable land features, including landmarks, streets, addresses, highway exits and Points of Interest, you must load your own high-detail custom map produced with our MapCreate soft- ware.
  • Page 120 3. To enter a street name, press ↓ to A. You can spell out the name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next let- ter and repeat until the name is correct, then press down to the lower selection list by pressing select a street name from the list, then press...

  • Page 121: Find Any Item Selected By Map Cursor

    Find By Name menu with list of cities. Find Any Item Selected by Map Cursor With a POI or map feature selected by the cursor, press to the previous page, press A POI selected by the cursor (left). POI information screen (right). NOTE: Since the Go To Waypoint command is highlighted, you can navi- gate to the selected POI by pressing...
  • Page 122 The Find Exit menu. 2. First, select a highway name by pressing , which calls up the Find By Name menu. There are two highway search options: A. You can spell out the highway name in the top selection box. Press ↑ or ↓ to change the first letter, then press →...
  • Page 123 Find Exit menu with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press navigate or "go to" the exit. B. Press →| map. Go To Exit highlighted (left). Find On Map selected (right). Tip: You can also look up some additional information on the Exit Ser- vices located near this exit.

  • Page 124: Find Map Places Or Points Of Interest (Poi)

    Exit Information screen (left). General location and amenities information (right). Find Map Places or Points of Interest (POI) 1. Press , press to select a map place or POI category, then ↓ ↑ press . (To narrow your search, press → then press ↓ or ↑ to select a subcategory before pressing .) You will be given two options;...
  • Page 125 Find by Nearest option, left, Calculating screen, center, POI list, right. 3. To search by the name of a POI: press . There are two options: A. You can spell out the POI in the top selection box. Press ↑ or ↓ to change the first letter, then press →...

  • Page 126: Find Streets Or Intersections

    Go To Waypoint highlighted (left). Find on Map selected (right). Find Streets or Intersections Find a Street 1. From the Map Page, press |↓ to and the Find MENU TREETS Streets Menu appears. 2. You must first fill in a street name in the First Street dialog box. Press to display the Find By Name menu.

  • Page 127: Find An Intersection

    for that street, press ↓ to ing you to wait while the unit finds the street. When the Streets Found list appears, press ↑ or ↓ to select the street you are searching for and press ENT. Find Streets menu with the Find First street highlighted (left). Streets 4.
  • Page 128 2. You must fill in a street name in the First Street dialog box. Press to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box. Press ↑ or ↓ to change the first letter, then press →...

  • Page 129: Find Waypoints

    ↑ or ↓ to select the intersection you are searching for and press . (In our example, we selected the intersection of SW 80th Street and SW 71st Avenue in Miami, Fla.) 7. The Map Page appears, with the cursor pointing to the found intersec- tion.
  • Page 130 3. If you're looking for nearest, the unit says it is calculating, then a list of waypoints appears. The closest waypoint is highlighted at the top of the list. The waypoint furthest from you is at the bottom of the list. 4.
  • Page 131 Find By Name menu (left). Waypoint Information screen (center). The found waypoint is highlighted by the cursor on the Map Page (right). A. To navigate to the waypoint, press . (Go To Waypoint com- mand is already highlighted.) The unit will show navigation infor- mation to the waypoint.
  • Page 132 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...

  • Page 133: Section 7: Nmea 2000

    Internal GPS Receiver GPS data from your internal GPS receiver can not be transmitted across the network to other network devices. The only way to transmit GPS data across the network is to add a LGC-2000 or LGC-3000 module to the LowranceNET.

  • Page 134: Bus Setup

    NOTE: To switch back to the internal GPS antenna, repeat the steps above. The internal GPS will be automatically enabled when you turn off (uncheck) the LGC module Set Active box. Bus Setup Selecting Bus Setup from the NMEA 2000 menu gives you access to the Bus Configuration menu and the NMEA Diagnostics and Ethernet Di- agnostics pages.

  • Page 135: Engine & Tank Configuration

    from IP Address to upload and download rates (bytes per second). To refresh either Diagnostics page, highlight the the bottom of the page and press The network devices list is located in the top half of the Bus Configura- tion menu. You can configure, calibrate and set alarms for devices ac- cessed from the Bus Configuration menu network devices list.

  • Page 136: Tank Size

    Tank Size The Tank Size menu allows you to input the size of a selected tank in gallons. After selecting the desired tank from the Tank Select menu, you are ready to enter the tank's size. Set Configuration button The Set Configuration button is used to finalize engine-tank configura- tion settings.

  • Page 137: Device Configuration Menu

    9. When all tanks have been configured, press the but- ONFIGURATION ton. The following confirmation message will appear: Are you sure you wish to change the bus configuration? Choose and press , Press to get back to the main display. EXIT Device Configuration Menu When a device is selected from the network devices list on the Bus Con-...

  • Page 138: Fuel Management Menu

    NOTE: If, as in the graphic above, you do not have a Suzuki Engine Inter- face, EP-15 Fluid Level or EP-10 Fuel Flow on the network, the Engine & Configuration menu, Tank Select menu, Tank Size dialog and Set Configuration button will not be displayed on the Bus Con- figuration menu.

  • Page 139: Fill Tank

    Fill Tank You will use the Fill Tank command when calibrating a fuel flow and when filling up the tank without calibration. Adding Fuel to Tank Tank Location, Fuel Added and Add Fuel commands work together to keep NMEA 2000 fuel data consistent with the actual amount of fuel added to the fuel tank(s).

  • Page 140: Nmea 2000 Alarms

    2. Highlight ANAGEMENT menu will appear. 3. Highlight to NGINE the engine attached to the desired fuel flow — and press 4. Highlight ESET tion message will appear: Are you sure you wish to Reset Calibration? Select and press been returned to factory defaults. To Reset Trip: The Reset Trip function allows you to reset to zero the running total of fuel used on a particular trip.

  • Page 141: Waypoint Sharing

    3. Highlight LUID EVEL vice you want to set an alarm for and press 4. Highlight the NABLED Empty Alarm) and press 5. To set the alarm percentage, press → to highlight 6. Use ↑ ↓, ← → to input the desired percentage and press Steps 3-4 to set the other alarm.

  • Page 142: Ep-35 Temperature Configuration

    EP-35 Temperature Configuration To input Device Name: 1. Press MENU MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight ETUP ration menu. A list of network devices will be at the top of the page. 3.

  • Page 143: Restore Defaults

    If you want to use your unit in a network including one of these digital gauges, you may need to consult customer service. You should never need this command if you are connecting your unit to a network with similar display units and/or a series of electronic probes.

  • Page 144: Advanced Options Menu

    To select a Location: 1. Press MENU| MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight ETUP ration menu. A list of network devices will be at the top of the page. 3.

  • Page 145: Ep-15 Fluid Level Configuration

    2. Highlight ETUP ration menu. A list of network devices will be at the top of the page. 3. Use ↑ ↓ to select the desired fuel flow and press Configuration menu will appear. 4. Highlight DVANCED 5. Select ESTORE EFAULTS appear: Are you sure you wish to change this device's configuration? 6.

  • Page 146: Advanced Options Menu

    To select Fluid Type: 1. Press MENU| MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight ETUP ration menu. A list of network devices will be at the top of the page. 3.

  • Page 147: Restore Defaults

    If you want to use your unit in a network including one of these digital gauges, you may need to consult customer service. You should never need this command if you are connecting your unit to a network with similar display units and/or a series of electronic probes.

  • Page 148: Advanced Options Menu

    and use ↑ ↓, ← → to input a name for the interface. Press 4. Press . Press repeatedly to return to the main display. EXIT To select a Location: 1. Press MENU| MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization.

  • Page 149: Restore Defaults

    network includes LMF-200 or LMF-400 digital gauges, which support the display of fewer electronic probes than your GPS or sonar/GPS unit. If you want to use your unit in a network including one of these digital gauges, you may need to consult customer service. You should never need this command if you are connecting your unit to a network with similar display units and/or a series of electronic probes.
  • Page 150 To check fuel flow accuracy: Select Fuel Used to be shown as Overlay Data on your unit's main dis- play. Refer to the Overlay Data segment of this manual for instructions on how to select Fuel Used data as Overlay Data. 1.

  • Page 151: Ep-15 Fluid Level Calibration

    To Reset Calibration: 1. Press MENU MENU 2. Highlight ANAGEMENT 3. Highlight NGINE appear with up to four options: All Engines, Port, Center and Star- board. Selecting All Engines will reset calibration for all engines back to factory defaults. 4. Select All Engines or the engine connected to the desired device and press 5.

  • Page 152: 3-Point Calibration

    The following message will appear pleted. Press , then press display. Calibrate is highlighted on the device configuration menu (left). Cali- bration menu (right) with calibration instructions listed at the top. 3-Point Calibration 3-point calibration is designed for tanks that vary in shape from the top to the bottom.

  • Page 153: 5-Point Calibration

    Highlight ALIBRATE pear: Full Level Calibration Completed. Press peatedly to get back to the main display. Num Pts menu with 5-point calibration selected (left). Half level selected on Fluid Level menu (center). Calibration Done window (right). 5-Point Calibration 5-point calibration is best suited tanks that vary greatly in shape from top to bottom.

  • Page 154: Fuel Flow Calibration In A Suzuki Engine Interface

    10. Add another quarter tank of fuel, which should raise the fuel level to half a tank. Highlight press ENT. Highlight ALIBRATE pear: Half Level Calibration Completed. Press 12. Add another quarter tank of fuel, which should raise the fuel level to 3 quarters of a tank.

  • Page 155: Engine Trim Calibration

    If the amount of fuel you added to the tank and the fuel used figure are off by more than 3 percent, we recommend the engine interface be cali- brated. NOTE: You must use the gauge's Fill Tank command when filling your fuel tank to keep the engine interface updated with correct information on the amount of fuel in the tank.

  • Page 156: Reset Trim Calibration

    Reset Trim Calibration If you are not satisfied with your engine trim calibration, you can reset engine trim calibration from the Suzuki Engine Interface Advanced Options menu. 1. Press MENU MENU 2. Choose and press ETUP connected to the desired engine and press 3.
  • Page 157 Reset Calibration highlighted (left). Reset Calibration confirmation window (right). 5. Highlight and press . The following message ESET ALIBRATION will appear: Are you sure you wish to Reset Calibration? 6. Highlight and press . Press repeatedly to get back to the EXIT main display.
  • Page 158 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...

  • Page 159: Section 8: Supplemental Material

    Section 8: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands...
  • Page 160 Chatham Island Astro 1971; New Zealand (Chatham Island) Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Nether-...
  • Page 161 Nahrwan United Arab Emirates Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Cos- ta Rica, El Salvador, Guatemala, Hondu- ras, Nicaragua North American 1927 Mean for Canada...
  • Page 162 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic Sys- tem 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay,...
  • Page 163 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...
  • Page 164 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...
  • Page 165 Notes www.Busse-Yachtshop.de email: info@busse-yachtshop.de...

  • Page 166: Fcc Compliance

    FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful inter- ference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 167 LOWRANCE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS.

  • Page 168: Databases Limited Warranty

    DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the prod- uct as a consumer item for personal, family, or household use. The Databases Limited Warranty applies to the one or more databases that your product may contain.
  • Page 169 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against defects or malfunctions in materials and workmanship, and against failure to conform to this product's written specifications, all for one (1) year from the date of original purchase by you.

  • Page 170: How To Obtain Service

    How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Lowrance parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department.

  • Page 171: Accessory Ordering Information

    Accessory Ordering Information for all countries To order Lowrance GPS accessories such as power cables or MMC cards, please contact: 1) Your local marine dealer, sporting goods or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items.

  • Page 172: Visit Our Web Site

    Visit our web site: Lowrance Pub. 988-0152-191 © Copyright 2006 All Rights Reserved Printed in USA 120706 Lowrance Electronics, Inc. www.Busse-Yachtshop.de email: info@busse-yachtshop.de...

Table of Contents