Table of Contents
Advertisement
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE OPERATION smell all around the appliance
area for gas. Be sure to smell
next to the floor because some
gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch;
do not use any telephone in your building.
•
Immediately call your gas supplier from a neighbor's tele-
phone.
•
Follow the gas supplier's instructions.
•
If you cannot reach your gas supplier, call the fire depart-
ment.
1. STOP! Read the safety information above before pro-
ceeding.
2. Refer to Figure 15. To turn off the gas supply, depress
the knob slightly and turn clockwise
position.
3. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low "B," in the safety information above. If you don't smell
gas, go to the next step.
4. Refer to Figure 16. Lo-
cate the pilot. It is at the
right side of the burner.
5. Refer to Figure 17.
Push in the control
knob and turn counter-
clockwise
to the
"PILOT" position. Hold
the control knob in for a
few seconds.
6. While still holding in the control knob, press the ignitor
push-button several times. This will cause a spark at the
pilot which will ignite the pilot gas.
7. Hold in the control knob for 60
seconds to prevent the flame failure
detector from shutting off the gas
while its probe is warming up.
8. Release the control knob.
•
If the knob does not pop up when
released, stop and immediately call
your service technician.
•
If the pilot will not stay lit after several tries, push in and
turn the gas control knob clockwise
Figure 16) and call your service technician or gas supplier.
9. When the pilot remains lit, turn the control knob counter-
clockwise
to the "ON" position. (Fig. 18)
Depress the control knob slightly and turn it clockwise
14
For Your Safety, Read Before Lighting
Fig.
14
Piezo
T118
Lighting Instr
Piezo
10/28/03 djt
Lighting Instructions for WRST
to the OFF
Fig. 16
T125
OP Pilot
10/28/03 djt
Fig. 17
PILOT
ON
OFF
T120
Lighting Instr
Pilot knob
to OFF (see
pilot
10/28/03 djt
To Turn OFF Gas to Appliance
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will
not push in or turn by hand, don't
try to repair it. Call a qualified
service technician. Force or at-
tempted repair may cause a fire
or an explosion.
D. Do not use this appliance if any
part of it has been under water.
Immediately call a qualified
service technician to inspect the
appliance and to replace any
part of the control system or gas
control which has been under water.
E. Be sure to install a 9 volt battery in both the receiver and the
remote, as required.
10. After the pilot is lit and the control knob is released, select
either the "ON" or "REMOTE" position of the receiver (Figure
1). If "ON" is selected, the burners are lit by turning the
control knob counterclockwise
off by turning the knob clockwise
"REMOTE" is selected, you control the burner ignition with
the hand held remote. For auto thermostat mode, press
the auto button. Set the desired room temperature. The
transmitter is factory calibrated with the lowest temperature
setting at 55º Fahrenheit and each setting above this is 5º
Fahrenheit each. Do not leave the remote in the "auto"
mode as this will reduce the batteries' capacity. For manual
remote operation press the "MAN" button. Press the "ON"
button to turn your fireplace on or the "OFF" button to turn it
off.
11. The flame height can be regulated by the knob located to
the right and rear of the main control knob. This is achieved
by turning it clockwise
counterclockwise
crease the flame height. This
should be in the highest position for
initial start up.
12. This appliance is fitted with a tran-
sient pilot burner for the sole pur-
pose of safe, momentary ignition of
the main burner in conjunction with
the piezo ignitor. When in operation
with the main burner, it contributes
to the base heat release and is
turned off by turning the control
knob to the OFF position.
13. The control knob should not be left at the "PILOT" setting
after the pilot has been ignited.
to the OFF position. Refer to Figure 15.
Fig. 15
PILOT
ON
T119
Lighting Instr
Pilot knob
off
10/28/03 djt
to "ON" (Fig. 18) or
to "PILOT". When
to increase flame height or
to de-
Fig. 18
PILOT
ON
T121
Lighting Instr
Pilot knob
ON
10/28/03 djt
20008055
OFF
OFF
Advertisement
Table of Contents
