Broan Elite EC62 SERIES Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Broan Manuals
  4. Ventilation Hood
  5. EC62 SERIES
  6. Installation instructions manual
Broan Elite EC62 SERIES Installation Instructions Manual

Broan Elite EC62 SERIES Installation Instructions Manual

Hide thumbs Also See for Elite EC62 SERIES:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION INSTRUCTIONS
HB0091
EC62 SERIES
!
INTENDED FOR DOMESTIC COOKING ONLY
!
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11 &
12.
Broan-NuTone Canada ULC; Mississauga, Ontario
www.broan.ca 1-877-896-1119
REGISTER YOUR PRODUCT ONLINE AT: www.broan.ca
21240 Rev. 01

Advertisement

Table of Contents
loading

Related Manuals for Broan Elite EC62 SERIES

Summary of Contents for Broan Elite EC62 SERIES

  • Page 1 INTENDED FOR DOMESTIC COOKING ONLY READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11 & Broan-NuTone Canada ULC; Mississauga, Ontario www.broan.ca 1-877-896-1119 REGISTER YOUR PRODUCT ONLINE AT: www.broan.ca 21240 Rev. 01...

  • Page 2: To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Observe The Following

    9. To reduce the risk of fire and electrical shock, the Broan Elite d) Use proper pan size. Always use cookware appropriate for the EC62 Series models must be installed only with their own size of the surface element.
  • Page 3 EC62 SERIES POWER PACK SYSTEM - TANDARD TANDARD ODEL ODEL 3¼” 10” R 3¼” 10” W 10" R APACITY OUND OT INCLUDED OT INCLUDED OT INCLUDED OT INCLUDED ODEL 10" R OUND DJUSTABLE LBOW OT INCLUDED ODEL 10" R OUND TANDARD —...

  • Page 4: Prepare The Installation

    1. PREPARE THE INSTALLATION WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: - Power Pack - Accessories:...
  • Page 5 To view specific model information, including depths for each liner model, visit www.broan.ca or contact Technical Support (phone number listed on front cover). To install, see instruction packed with custom hood liner.

  • Page 6: Remove Filter

    5. CUT THE HOLE IN CUSTOM HOOD BASE If it is not done yet, cut a hole in the bottom of the custom hood, using the dimensions shown at right. NOTE: Keep in mind that the unit exterior flange is 3/4’’ . 13³/ ”...

  • Page 7: Install The Adapter/Damper

    9. REMOVE THE ELECTRICAL KNOCKOUT From inside the power pack, punch out the electrical knockout hole on top right side (C) OR on back right side (D). Install the wire clamp (included in parts bag). HR0030 10. REMOVE THE KNOCKOUT OPENING ( SINGLE BLOWER MODEL ONLY Remove the knockout opening on top (vertical discharge installation) or on back (horizontal...
  • Page 8 12. INSTALL THE ADAPTER AND THE DAMPER ( DUAL BLOWER MODEL ONLY) (CONT'D) AMPER HINGE PARALLEL TO Install 10” damper inside the VERTICAL ductwork that will be attached to power pack. Do not install POWER PACK in a horizontal ductwork or it will not open and close properly. Remove shipping tape if present. SIDES To optimize airflow and reduce noise, position the damper at least 17”...

  • Page 9: Reinstall The Blower

    14. INSTALL POWER PACK (CONT'D) From inside the power pack, using provided no. 8-10 x 1/2” screws, mount the power pack to the custom hood base. To do so, raise the front until its flange rests on the outer side of the custom hood base and use 2 screws to secure in place.

  • Page 10: Connect Wiring

    17. REINSTALL FRONT PANEL AND WIRING COVER CAUTION Take care not to pinch wiring when reinstalling the front panel and the wiring cover. Carefully reassemble the front panel to the power pack by aligning the tabs with their corresponding slot. Using a Robertson or a Phillips no.

  • Page 11: Led Lighting

    19. REINSTALL FILTERS CAUTION Remove protective plastic film covering filters before installing them. 1. Using a Phillips no. 2 screwdriver, assemble the knob to each filter. NOTE: The screw MUST BE on filter tabs side. See illustration at right. HO0139 2.

  • Page 12: Operation

    21. USE AND CARE (CONT'D) Power Pack Cleaning Stainless steel cleaning: Don’t: • Regularly wash with clean cloth or rag soaked with warm water • Use any steel or stainless steel wool or any other scrapers to and mild soap or liquid dish detergent. remove stubborn dirt.

  • Page 13: Wiring Diagram

    IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT BULBS, FUSE, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING.

  • Page 14: Service Parts

    ARTS AND EPAIRS In order to ensure your unit remains in good working condition, you must use Broan-NuTone genuine replacement parts only. Broan-NuTone genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety.

Table of Contents