Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Linear VS-GSWG
Summary of Contents for Linear VS-GSWG
- Page 1 VS-GSWG Swing Gate Operator Installation Guide Operator models contained in this manual conform to UL325 standard for use in Class I, II, III, and IV applications USA & Canada (800) 421-1587 & (800) 392-0123 (760) 438-7000 - Toll Free FAX (800) 468-1340...
-
Page 2: Table Of Contents
FCC Notice ..........25 Model VS-GSWG Exploded View ......26 Controller Parts List . -
Page 3: Pre-Installation Information
2. Read the yellow “Safety Instructions” brochure enclosed with the packet of information. If any pages are missing or are unreadable, or you do not have the safety instructions, please call Linear at 1-800-421-1587 to request additional copies. 3. ALL ELECTRICAL CONNECTIONS TO THE POWER SUPPLY MUST BE MADE BY A LICENSED ELECTRICIAN AND MUST OBSERVE ALL NATIONAL AND LOCAL ELECTRICAL CODES. -
Page 4: Wiring Specifi Cations
Twisted Pair Shielded Cable (or equivalent) only – P/N 2500-1982, per foot). See Page 21 for details of this connection. Note: The shield wire should be connected in both the operators. VS-GSWG Swing Gate Operator Installation Guide MODEL VS-GSWG SINGLE PHASE POWER WIRING MAXIMUM DISTANCE (FEET) VOLTS &... -
Page 5: Mounting Pad Installation
✓ NOTE: If non-standard mounting is necessary, consult the factory. VS-GSWG Swing Gate Operator Installation Guide The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access opening. -
Page 6: Operator Preparation
✓ NOTE: Observe the way the chain threads around the sprockets for left-hand or right-hand installations. Refer to Figure 4. 6. Adjust for taut chain tension but do not overtighten. 7. Replace the arm assembly cover. VS-GSWG Swing Gate Operator Installation Guide GEAR REDUCER INSTALL THE VENT PLUG... -
Page 7: Operator Setup
AND MUST OBSERVE ALL NATIONAL AND LOCAL ELECTRICAL CODES AC Power Connection All Linear gate operators are supplied with a power disconnect switch to turn on and off the power available to the operator. Following wiring specifi cations on Page 2, incoming power should be brought into the operator and connected to the labeled pigtails from the disconnect box. -
Page 8: Open And Close Limit Adjustment
Care must be taken not to adjust too close to the center as the limit nut may travel past the switch and start accelerating at the end of the cycle. VS-GSWG Swing Gate Operator Installation Guide RIGHT-HAND INSTALLATION... -
Page 9: Torque Limiter Adjustment
✓ NOTE: The open and close current sensing may need to be adjusted before performing the following two steps. See Page 13. To adjust the torque limiter in a Model VS-GSWG: 1. Loosen the set screw on the adjustment nut. -
Page 10: Controller Features
TERMINALS 3-BUTTON STATION TERMINALS OPEN AND CLOSE OBSTRUCTION REVERSE INPUT TERMINALS INPUT TERMINALS OPEN LOOP INPUT TERMINALS VS-GSWG Swing Gate Operator Installation Guide OPERATION AND PROGRAMMING OPERATION INDICATORS BUTTONS SHADOW/RESET REVERSE LOOP LIMIT SWITCH INPUT TERMINALS INPUT TERMINALS SHADOW/RESET LOOP INPUT TERMINALS Figure 11. -
Page 11: Indicator Descriptions
MAXIMUM CLOSE "CC" CURRENT ADVANCED "AD" PROGRAMMING VS-GSWG Swing Gate Operator Installation Guide INDICATION WHEN LIT DURING NORMAL OPERATION LOW VOLTAGE AC POWER IS PRESENT LOW VOLTAGE DC POWER IS PRESENT OPEN SIGNAL PRESENT FROM THE INTERNAL RECEIVER OR AN EXTERNAL DEVICE... -
Page 12: Terminal Descriptions
AUX RELAY N.C. 24 VOLT SOLAR PANEL 24 VOLT BATTERY VS-GSWG Swing Gate Operator Installation Guide FUNCTION FACTORY CONNECTED TO 24 VAC FROM TRANSFORMER OR 24 VDC FROM CONTINUOUS DUTY DC SUPPLY. PROVIDES 24 VOLT DC POWER FOR ACCESSORIES. (.5A MAX) FACTORY CONNECTED TO THE CONTROLLER’S RESET BUTTON. -
Page 13: Operator Accessory Connections
Operator Accessory Connections 3-BUTTON STATION KEYSWITCH FIRE ACCESS SWITCH SINGLE-CHANNEL RADIO RECEIVER TWO-CHANNEL RADIO RECEIVER CHANNEL #1 OPEN/CLOSE VS-GSWG Swing Gate Operator Installation Guide TELEPHONE ENTRY KEYPAD SOLENOID LOCK EXTERNAL POWER MAGLOCK WARNING STROBE OR AUDIBLE SOUNDER Figure 12. Operator Accessory Connections... -
Page 14: Basic Controller Programming
1 to 59 seconds and from 1 to 9 minutes. When the Auto Close Timer is set, after opening, the gate will wait for the length of the Auto Close Timer then close automatically. VS-GSWG Swing Gate Operator Installation Guide DOWN PRESS DOWN AND UP... -
Page 15: Run Alarm And Pre-Start Alarm
Using the + and - buttons, set the programmed range number so that a minimal force (50-75 lbs.) will activate a reversal should an obstruction occur, but high enough to keep the gate moving under normal conditions without interruption. VS-GSWG Swing Gate Operator Installation Guide FUNCTION OPTIONS "RP"... -
Page 16: Advanced Controller Programming
Stagger Mode. The Stagger Delay Time can be set from 1-99 seconds. ✓ NOTE: This function will only be displayed if dual gate operation is selected. VS-GSWG Swing Gate Operator Installation Guide FUNCTION OPTIONS "AD"... -
Page 17: Auxiliary Relay Mode
Brake Delay Time This function is displayed, but only used in operators with mechanical brakes. The Model VS-GSWG does not have a mechanical brake. The factory default sets the Brake Delay to no delay (0 seconds). Heavy gates may require delayed braking to allow the gate to slow down before stopping it. -
Page 18: Reset Cycle Count
The Controller is supplied with a local whip antenna installed. If using a remote antenna, remove the whip antenna and connect coax cable from the antenna to the ANTENNA connector. VS-GSWG Swing Gate Operator Installation Guide FUNCTION "CT" RESET CYCLE... -
Page 19: Radio Transmitter Learn
STORED IN MEMORY. NOTE: THIS FUNCTION WILL NOT ERASE TRANSMITTERS, CURRENT SENSE VALUES, OR MOTOR TYPE. RESET TO FACTORY DEFAULTS VS-GSWG Swing Gate Operator Installation Guide FUNCTION PRESS ENTER (ONCE FOR EACH TRANSMITTER, ENTER UP TO 40 TRANSMITTERS TOTAL) "TL"... -
Page 20: Loop Layout Illustration
Loop Layout Illustration - 18 - VS-GSWG Swing Gate Operator Installation Guide P1250 Revision X6 7-8-2011... -
Page 21: Safety Edge Layout Illustration
Safety Edge Layout Illustration - 19 - VS-GSWG Swing Gate Operator Installation Guide P1250 Revision X6 7-8-2011... -
Page 22: Photoeye Installation Illustration
Photoeye Installation Illustration - 20 - VS-GSWG Swing Gate Operator Installation Guide P1250 Revision X6 7-8-2011... -
Page 23: Dual Gate Installations
CONNECT SHIELD WIRE AT BOTH ENDS SHIELD Figure 13. COMM LINK Wiring VS-GSWG Swing Gate Operator Installation Guide Optional In-Cabinet Heater The operator can be ordered with an optional cold weather package that includes an in-cabinet heater to keep the drive train and electronics warm in cold environments. -
Page 24: Gate Operation
If the auto close timer is set, when the close obstruction input is cleared, the gate will close when the auto close timer expires. VS-GSWG Swing Gate Operator Installation Guide Reverse Input If the reverse input is triggered while the gate is closing, the gate will reverse to the full open position. -
Page 25: Error Indications
Maximum Run Time has been exceeded, the sounder will beep twice every fi ve seconds. The next operation of the gate will clear the indication. VS-GSWG Swing Gate Operator Installation Guide CONTROLLER ERROR CAUSES AND INDICATIONS ERROR CAUSE... -
Page 26: How To Order Replacement Parts
A. Check the setscrews in limit cams for tightness. Replace if necessary. Contact your local Linear dealer or distributor to order parts. 1. Supply the model number and serial number of your operator. 2. Specify the quantity of pieces needed and order by part number and name of part. -
Page 27: Preventative Maintenance
Always disconnect power from operator before servicing. Keep clear of gate during operation. General Linear gate operators are designed for many years of trouble-free operation and, under recommended operating conditions, will require only minimal maintenance. To ensure that a unit is ready for operation at all times, and to preclude serious damage or failure, inspect the unit systematically. -
Page 28: Model Vs-Gswg Exploded View
Model VS-GSWG Exploded View - 26 - VS-GSWG Swing Gate Operator Installation Guide P1250 Revision X6 7-8-2011... - Page 29 REF. # VS-GSWG Swing Gate Operator Installation Guide MODEL SWG MECHANICAL PARTS LIST PART # DESCRIPTION 2120-361 Complete Enclosure Assembly with Door 2110-067 Enclosure Assembly without Door 2120-362 Enclosure Door and Lock Assembly 2110-643 Snap Lock Assembly only 2110-161 Mounting Panel Assembly...
-
Page 30: Controller Parts List
Enclosure with Cover Transformers 2500-212 115V to 24V, 40VA 2500-791 208/230V to 24V, 40VA 2500-214 460V to 24V, 40VA VS-GSWG Swing Gate Operator Installation Guide REF. # DESCRIPTION - 28 - PART # DESCRIPTION Hitachi Controllers 2500-2244 1/2 HP, 115V, 1-Phase... -
Page 31: Variable Speed Drive Programming
TARGET SPEED SECOND SPEED MIN SPEED AUTO RESET TERM 3 FUNC TERM 4 FUNC VS-GSWG Swing Gate Operator Installation Guide NOTE: L200 model must have this switch in the UP (SR) position. List of parameters set at factory RECOMMENDED FUNCTION... -
Page 32: Gate Arm Assembly Parts List
Hex Nut, 3/8”-16 2200-006 #40 Master Link 2200-658 #40 Chain, 72 Links 2100-1168-BT Cover for 78” Arm Parts for non-standard 63” VS-GSWG Gate Arm 2110-257 Gate Arm Assembly, 63” (complete) 2110-271 Welded Rail Assembly, 63” 2200-420 #40 Chain, 57 Links 2100-1167-BT Cover for 63”... - Page 33 This page left blank intentionally. - 31 - VS-GSWG Swing Gate Operator Installation Guide P1250 Revision X6 7-8-2011...
-
Page 34: Gate Operator Installation Checklist
By signing this installation checklist, I/we hereby certify that each item listed and checked above has been covered by the installer and is clearly understood by the customer. Customer’s Signature Installer’s Signature VS-GSWG Swing Gate Operator Installation Guide Date Date - 32 -...