Dimensional Drawing; Location; General - Carrier 58UHV Installation, Start-Up, And Operating Instructions Manual

"
1
28 ⁄
2
FLUE COLLAR
7
⁄ -IN. DIA HOLE
8
POWER ENTRY
7 ⁄ -IN. DIA
8
ACCESSORY
3
1 ⁄ -IN. DIA HOLE
" 4
7
39 ⁄
8
GAS ENTRY
1
⁄ -IN. DIA HOLE
2
THERMOSTAT
WIRE ENTRY
SIDE INLET
"
5
24 ⁄
16
"
11 ⁄
16
AIR INLET
UNIT SIZE
060-12
080-16
100-20
120-20
Improper installation, adjustment, alteration, service, mainte-
nance, or use can cause carbon monoxide poisoning, explo-
sion, fire, electrical shock, or other conditions which may
cause personal injury or property damage. Consult a qualified
installer, service agency, local gas supplier, or your distribu-
tor or branch for information or assistance. The qualified
installer or agency must use only factory-authorized and
listed kits or accessories when modifying this product. A
failure to follow this warning can cause electrical shock, fire,
personal injury, or death.
This furnace is designed for a minimum continuous return-air
temperature of 60°F db or intermittent operation down to 55°F db
such as when used with a night setback thermostat. Return-air
temperature must not exceed 85°F db.
To aid in installation, troubleshooting, and service, a status code
label is located on the blower compartment door. This label
explains how to use the LED status indicator on the furnace control
which is viewed through the sight glass on the door.
For high-altitude installations, the high-altitude conversion kit
MUST be installed at or above 5500 ft above sea level.
"
1
2 ⁄
16
1"
"
3
5 ⁄
8
"
5
12 ⁄
16
"
13
5 ⁄
16
"
3
2 ⁄
8
3"
"
11
⁄
16
NOTES: 1. Two additional
2. Minimum return-air opening at furnace:
a. For 800 CFM–16-in. round or 14
b. For 1200 CFM–20-in. round or 14
c. For 1600 CFM–22-in. round or 14
d. For airflow requirements above 1800 CFM, use both side inlets,
a combination of 1 side inlet and the bottom, or the bottom only.
Fig. 1—Dimensional Drawing
Table 2—Dimensions (In.)
A D
14-3/16 12-9/16
21 19-3/8
24-1/2 22-7/8
24-1/2 22-7/8
A
"
D
13
⁄
16
"
3
5 ⁄
8
"
2 11 ⁄
16
"
13
5 ⁄
16
"
3
2 ⁄
8
TYP 1 "
"
11
⁄
16
E
"
5
⁄
8
TYP
7 ⁄ -in. dia knockouts are located in the top plate.
8
1
⁄ x 12-in. rectangle.
2
1 1
⁄ x 19 ⁄ -in. rectangle.
2 2
1 1
⁄ x 23 ⁄ -in. rectangle.
2 4
E FLUE COLLAR
12-11/16
19-1/2
23
23
For accessory installation details, refer to the applicable installa-
tion literature.
NOTE: Remove all shipping brackets and materials before oper-
ating the furnace.
Step 1—Location

GENERAL

Do not install furnace in a corrosive or contaminated atmo-
sphere. Make sure all combustion and circulating air require-
ments are met.
3
AIRFLOW
"
1
2 ⁄
16
19"
OUTLET
1"
7 ⁄ -IN. DIA
8
POWER ENTRY
1
1 ⁄ -IN. DIA
2
R.H. GAS ENTRY
7
⁄ -IN. DIA ACCESSORY
8
1
⁄ -IN. DIA THERMOSTAT
2
WIRE ENTRY
SIDE INLET
1"
"
1
23 ⁄
4
SIDE RETURN
DUCT LOCATION
SHIP. WT
4 134
4 154
4 184
5 194
"
13
⁄
16
"
1
14 ⁄
2
"
1 3 ⁄
4
A88367