Adjusting The Picture Quality (Picture Control) - Denon DBP-4010UDCI Owner's Manual

ENGLISH
0
5
00
0008
@000
8 8 8 8
• On adjusting the brightness on the output side of bright parts on
the disc side, the normally hard to see bright parts become clearly
discernible images.
*
1 : This is not available for HOM I output.
*
2 : Effective only for the 480i video signal from the video output terminal, S
video output terminal, and component video output terminal.
*
3 : This has no effect with the video and S-Video outputs.
*
4 : This has no effect with the video and S-Video outputs when playing PAL
video.
About Gamma Correction
When you select "Gamma Correction", and then press
8,
you can
change the setting with
<:;I::;>
<::0
e
B·
In the example of the graph below, the horizontal axis shows the
brightness level of the pictured recorded on the disc. The vertical axis
shows the brightness of the picture output by the DBP-401 OUDCI.
• On adjusting the brightness on the output side of dark parts on
the disc side, the normally hard to see dark parts become clearly
discernible images.
o
Resuming Initial Values after Gamma
Correction
Press
(~)
while a graph is displayed.
o
o
o
o
o
Default
GO
=
24 / G1
=
32
G2
=
48 / G3
=
64
G4
=
80 / G5
=
96
G6
=
128 / G7
=
160
G8
=
192 / G9
=
224
GO - 9
0-+3
-6 - +6
0-+12
0-+11
-6 - +6
-6 - +6 0
-6 - +6 0
-5 - +5
0
-5 - +5 0
-6 - +6 0
OIRE
7.5 IRE
7.5 IRE
-7 - +7 0
-7 - +7 0
Setting
contents
Setting items
Sharpness (medium range)
*
1, 3
Adjust picture sharpness
for the medium frequency
range.
DNR
Reduce noise in the entire
picture.
Gamma Correction
*
1
Adjust video brightness in
detail.
Sharpness (high range)
*
3
Adjust picture sharpness for
the higher frequency range.
Brightness
Adjust picture brightness.
White Level
Adjust the white level.
Hue (color tone)
*
4
Adjust the green and red
color balance.
Enhancer
*
3
Strengthens the contours of
the picture.
Contrast
Adjust picture contrast.
Black Level
*
3
Adjust the black level.
Chroma Level
Adjust the color density.
Setup Level
*
2
Adjust the black areas of the
image.
V.Position
*
3
Adjust the top/bottom
position.
H.Position
*
3
Adjust the left/right position.
~~
88B
r<:0(5
Gr-;-,~
8088
88@E)
DODD
QD@IDnEJ
3
Select the item you want to change
with
<:;I::;>
<::0.
4
Change the setting with
e
B·
1
Press~.
The currently set status is displayed.
*
Refer to the table on the right regarding contents of items which
can be set.
2
Select the memory number you want ("Memory I" -
"Memory 5") with
<:;I::;>
<::0, and then press
8.
You can adjust the picture quality to your liking.
You can store up to a maximum of 5 values in memory.
Adjusting the Picture Quality (Picture Control)
o
When Outputting Standard Picture Quality without
Using Picture Adjustment
~~
8
Press
0
and <:;I::;>
<::0
to select "Standard" and then press
IHTBl •
o
When Finishing Picture Adjustment
Press
~
during picture adjustment.
The picture adjustment set values are retained in memory even after
the power is turned off.
33