Cables Used For Connections' 12 1. Home Theater Playback - Playing Back Using Multi-Channel System; Using An Hdmi Cable To Connect To An Av Amp Or Television· . 13 Required Settings For Hdmi Connection - Denon DBP-4010UDCI Owner's Manual

ENGLISH
1. Home Theater Playback - Playing Back Using Multi-channel System -
HOMI
IN
nop
(720 progressivei
1080i
(1080 interlaced)
Source Direct - - 480/576i - - 480/576P
(Source direct) (480/576 interlaced) (480/576
prOgreSSiV~
1080P
(1080 progressive)
• If the HDMI resolution is not set to "Auto", set it to correspond with the resolution of your television.
Images will not be projected normally if the television resolution and DBP-401 OUDCl's output resolution
do not match.
• Audio and video will be temporarily interrupted if the power of the connected device currently playing
back is turned off, or input is switched.
• When you change the HDMI video resolution of the DBP-401 OUDCI, it takes from a few seconds up to
about 10 seconds for validation between the DBP-4010UDCI and the connected device. Audio/video is
not output during this period.
• When outputting deep colour or 1080p, etc., we recommend you use High Speed HDMI cable for
enhanced high-quality playback.
o
Connection to a device with a OVI-O terminal
If you use a HDMIIDVI-D conversion cable (sold separately), HDMI video signals are converted to DVI-
D signals, enabling connection to a device with a DVI-D terminal.
'N,n-
• In this case, the audio signal is not output. Make the appropriate audio connections for your devices.
(Grpage 14 - 20).
• The video signal will be in RGB format.
• You cannot output to a DVI-D device that does not support HDCP (high-bandwidth digital content
copyright protection system).
• Video may not be output depending on the combination of devices.
Setting HOMI video output
o
Make HOMI Output Signal and HOMI Control Function Settings
"HDMI Setup" (Grpage 23,24)
o
Make the Video Output Signal Setting for the Connected Television
"Video Setup" ((W'page 24)
o
About HOMI Video Resolution Setting
RESOLUTION
• Change the HDMI video resolution by pressing
I
~~~'
].
Switch the output mode as follows. Default
settings are underlined.
[
Auto
(Auto)
1080P24
(1080 progressive, 24-frame)
I
Required Settings for HOMI Connection
• When connecting with an HOMI cable, press
ll\;l
and set it to "HOMI On".
• OBp·4010UOCI automatically detects audio/video signal supported by the connected HOMI
device and outputs the signal. To change the setting, see "HOMI Setup" on the GUI menu
IGT'page 23, 24).
• When you press
l~)
and set it to "HDMI On", no video signals are output from the component
video outputs.
• To disable video or audio output from the HDMI terminal, set "Video Out" of "Pure Direct Setup",
which outputs high quality analog audio to "Off". To enable the HDMI signal output. set the Pure
Direct mode to one of the following setting:
• Pure Direct mode"Off" or "User Preset 1" or "User Preset 2"' ('*)
("Playing Back High-Quality Audio (Pure Direct Function) " Grpage 38)
'* Do this after setting "Pure Direct Setup" - "User Preset 1" or "User Preset 2" - "Video Out" on GUI
menu to "On" (Grpage 28)
During "HOMI On"
Audio/video signals are output from the HDMI terminal.
When the HDMI video resolution is set to "Auto" as described in "About HDMI Video Resolution
Setting" (Gr page 13), the DBP-401 OUDCI outputs the highest resolution video signal that is supported
by the connected equipment.
AVAmp or
TV
Using an HOMI Cable to Connect to an AV Amp or Television
I
i
'N'O-
I
I
I
I'N,n-
"
• When audio/video signals are output from the HDMI terminal, no video signals are output from the
component terminals.
• When a signal comprising 24 frames per second, such as 1080P24, is output from the HDMI terminal,
no video signals are output from the video or S-Video outputs.
I
Durin "HOMI Off"
l
Audiolvideo is not output from the HDMI terminal.
I
When outputting a video signal comprising 24 frames per second from the HDMI terminal, select
"1080P24" or "Source Direct" after setting the GUI menu "HDMI Setup" - "I/P Direct" (Grpage 23) to
"On".
I
See overleaf>
13