Table of Contents
Advertisement
Available languages
Available languages
NOTICE: Risk of property damage.
Never pull water supply hose to move
pres sure washer. This could damage
hose and/or pump inlet.
• DO NOT use hot water, use cold
water only.
• Never turn water supply off while
pressure washer engine is running
or damage to pump will result.
• DO NOT stop spraying water for
more than two minutes at a time.
Pump operates in bypass mode
when spray gun trigger is not
pressed. If pump is left in bypass
mode for more than two minutes
internal components of the pump
can be damaged.
If you do not understand these
precautions,
please
contact
our
customer
service
department
at
www.BlackandDecker-la.com!
Prior to starting, refer to your engine
manual for proper starting procedure.
1.
In a well ventilated outdoor area
add fresh, high quality, unleaded
gasoline with a pump octane rating
of 86 or higher. Do not overfill. Wipe
up spilled fuel before starting the
engine. Refer to Engine Owners
Manual for correct procedure.
2.
Check engine oil level. See Engine
Owners
Manual
for
correct
procedure.
3.
Connect the water hose to the
water source. Turn the water
source on to remove all air from
the hose. When a steady stream
of water is present, turn the water
source off.
4.
Verify the filter screen (M) is in
water inlet of pump.
NOTE: Cone side faces out.
8
M
58- ENG
5.
Connect high pressure hose (C) to
pump outlet (I).
9
I
C
6.
Connect water source (N) to pump
inlet (J).
NOTE: Water source must provide
a minimum of 5 gallons per minute
at 20 psi.
10
N
J
WARNING:
To
reduce
the
possibility of contamination always
protect
against
backflow
when
connected to a potable water system.
7.
Choose the correct nozzle for the
job to be performed. See how
To Use spray Wand instructions
in this section. NOTE: If applying
a chemical or cleaning solution,
see how To Apply Chemicals/
Cleaning Solvents instructions in
this section.
8.
Turn water source on.
NOTICE: Risk of property damage.
Failure to do so could cause damage
to the pump.
9.
Remove all air from the pump and
high pressure hose by depressing
trigger until a steady stream of
water is present.
10. Start engine. See Engine Owners
Manual for correct procedure.
WARNING:
Risk
of
unsafe
operation. If engine does not start
after two pulls, squeeze trigger of
gun to relieve pump pressure. Pull
starter cord slowly until resistance
is felt. Then pull cord rapidly to avoid
kickback and prevent hand or arm
injury.
11. Depress trigger on gun to start
water flow.
WARNING:
Risk
of
unsafe
operation. Stand on a stable surface
and grip gun/spray wand firmly with
both hands. Expect the gun to kick
when triggered.
12. Release trigger to stop water flow.
WARNING: Risk of injury from
spray. Always engage the trigger lock
(O) when gun is not in use. failure
to do so could cause accidental
spraying.
11
O
ShUTTING DOWN
1.
After each use, if you have applied
chemicals, place detergent siphon
hose into container of clean water
and draw clean water through
chemical injection system to rinse
system thoroughly.
NOTICE: Risk of property damage.
Failure to do so could cause damage
to the pump.
Turn engine off. See Engine
2.
Owner's Manual.
NOTICE: Risk of property damage.
NEVER turn the water off with the
engine running.
3.
Turn water source off.
4.
Pull trigger on spray gun to relieve
any water pressure in hose or spray
gun.
See Storage section in this manual
5.
for proper storage procedures.
59 - ENG
MAINTENANCE
WARNING: Risk of burn hazard.
When performing maintenance, you
may be exposed to hot surfaces,
water pressure or moving parts that
can cause serious injury or death.
WARNING: Risk of fire hazard.
Always disconnect, spark plug wire,
let the engine cool and release all
water pressure before performing
any maintenance or repair. The
engine contains flammable fuel. Do
not smoke or work near open flames
while performing maintenance.
To ensure efficient operation and longer
life of your pressure washer, a routine
maintenance schedule should be
prepared and followed. If the pressure
washer is used in unusual conditions,
such as high-temperatures or dusty
conditions, more fre quent maintenance
checks will be required.
ENGINE
Consult the Engine Owners Manual for
the man u fac tur er's recommendations
for any and all maintenance. NOTE: The
engine drain plug is located at the rear
of the unit.
PUMP
The pump was filled with oil at the factory.
The pump on this unit is maintenance
free and requires no oil. If there is a
problem with the pump contact us at
www.BlackandDecker-la.com
CONNECTIONS
Connections on pressure washer hoses,
gun and spray wand should be cleaned
regularly and lubricated with light oil or
lithium grease to prevent leakage and
damage to the o-rings.
NOZZLE CLEANING (fIG. 12)
If
the
nozzle
becomes
clogged
with foreign materials, such as dirt,
excessive pressure may develop.
If
the nozzle becomes partially clogged
or restricted, the pump pressure will
pulsate. Clean the nozzle immediately
using the nozzle kit supplied and the
following instructions:
Advertisement
Table of Contents
