Page 1
848 LAT OPTION USER’S GUIDE CLASS H PART # 7080301 REV. B WARNING: Read and follow all directions for each step to insure proper assembly of this product. Version: 848107 Revision: 07/10/01...
7. Inspect cables and their connections before using machine. Pay particular attention to the cable ends. DO NOT attempt to fix. Notify your authorized ParaBody dealer before use and have repairs made by an authorized service technician. 8. Make sure all spring loaded pull pins are fully engaged in the adjustment position and fully tighten thumbscrew before use.
Please note: * Thank you for purchasing the ParaBody 848 LAT OPTION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated.
PART # DESCRIPTION 6826608 BASE 6826908 UPRIGHT 6825408 STAND 6827208 CROSS BRACE 6825502 CARRIAGE 6275302 LAT BAR 6274402 LOW ROW BAR 6542402 3/16 X 1-3/4 X 5-1/4” PLATE 6824801 CABLE 3103102 1 X 8” GRIP 3116201 3-1/2” PULLEY 6177001 2-1/2 X 5-1/2” NON-SKID STRIP 6405201 2”...
Page 5
3/8 X 2-3/4” 25 FIGURE 1 STEP 1: • Assemble two 2” SQ. COVER CAPS (14) onto the ends of the STAND (3) as shown in FIGURE 1. • SECURELY assemble the one 3/8 X 2-3/4” BOLT (25), two 3/8” WASHERS (19), and one 3/8” LOCK NUT (20) to the STAND (3) as shown in FIGURE 1.
Page 6
FIGURE 3 STEP 3: • Insert two 2” SQ. END CAPS (13) into the ends of the CROSS BRACE (4) as shown in FIGURE 3. • Assemble two 2-1/2 X 5-1/2” NON-SKID STRIPS (12) to the CROSS BRACE (4) as shown in FIGURE 3. •...
Page 7
STEP 5: • Assemble the STAND (3) to the UPRIGHT (2) as shown in FIGURE 5. • Slide the CARRIAGE (5) over the UPRIGHT (2) as shown in FIGURE 5. • Assemble the BASE (1) to the UPRIGHT (2) as shown in FIGURE 5.
Page 8
3/8 X 2-3/4” 25 FIGURE 6 STEP 6: • SECURELY assemble the BASE (1) to the UPRIGHT (2) using one 1/2 X 3” BOLT (27), two 1/2” WASHERS (21) (slide front washer INSIDE of tube), and one 1/2” LOCK NUT (22). See FIGURE 6. •...
Page 9
3/8 X 2-3/4” 25 FIGURE 7 STEP 7: • Route the CABLE (9) through the UPRIGHT (2) as shown in FIGURE 7. • SECURELY assemble three 3-1/2” PULLEYS (11) into the slots of the UPRIGHT (2) using three 3/8 X 2-3/4” BOLTS (25), six 3/8” FLANGE SPACERS (31), and three 3/8”...
Page 10
FIGURE 8 STEP 8: • Attach the CABLE (9) from the UPRIGHT (2) to the CARRIAGE (5) using one 1/4” QUICK LINK (29) as shown in FIGURE 8. (IMPOR- TANT! Securely tighten QUICK LINK.) • Place one 3-1/2” PULLEY (11) into the loop of the CABLE (9) below the second and third PULLEY of the UPRIGHT (2) as shown in FIGURE 8.
Page 11
FIGURE 9 STEP 9: • Route the end of the second CABLE (9) through the slot on the UPRIGHT (2) then SECURELY assemble one 3-1/2” PULLEY (11) to the UPRIGHT (2) using two 3/8 X 2-1/2” BOLTS (24), two 3/8 X 3/8” SPACERS (30), four 3/8” WASHERS (19), and two 3/8” LOCK NUTS (20).
Page 12
26 3/8 X 4-1/2” FIGURE 10 STEP 10: • SECURELY assemble the CABLE (9) to the BASE (1) using one 3/8 X 4-1/2” BOLT (26), one 3/8 X 1” SPACER (32), and one 3/8” LOCK NUT (20) as shown in FIGURE 10.
Page 13
FIGURE 11 STEP 11: • Slide two 1 X 8” GRIPS (10) on the LOW ROW BAR (7) and two 1 X 8” GRIPS (10) on the LAT BAR (6) as shown in FIGURE 11. • Attach the LAT BAR (6) to the ball end of the upper CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11. •...
Page 14
FIGURE 12 STEP 12: • To use the 848101 LAT OPTION: (NOTE: LAT OPTION MUST BE USED WITH A BENCH. LAT OPTION CANNOT BE USED WHILE STAND IS ATTACHED. STAND MUST BE ATTACHED WITH THE FEET OUT AS SHOWN.) • Tilt the 848101 back and remove the STAND (3) as shown in FIGURE 12.
Page 15
Insert the UPRIGHT (2) of the 848 into the bench as shown in FIGURE 13. Thank you for purchasing the Parabody 848 LAT OPTION. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your ParaBody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody.