Related Manuals for ParaBody Parabody 663
Summary of Contents for ParaBody Parabody 663
- Page 1 663 660 SECOND STACK OPTION USER’S GUIDE CLASS H PART # 7050101 REV. C WARNING: Read and follow all directions for each step to insure proper assembly of this product. Version: 663101 Revision: 07/31/01...
- Page 2 Safety Statement...2 General Notes...3 Tools Required...3 Parts list...4 IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES! 1. Before using, read all the warnings and instructions on the use of this machine. Use only for intended exercise.
-
Page 3: Tools Required For Assembly
Please note: * Thank you for purchasing the ParaBody 663 660 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. -
Page 4: Parts List
FIGURE 2 STEP 2 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the bottom of the front SHROUD & rear SHROUD. Remove the SHROUDS from the 660101 HOME GYM. See FIGURE 2. PARTS LIST PART #... - Page 5 HEAD PLATE D-RING CABLE (7041801) FIGURE 3 STEP 3 • Unscrew the threaded ends of the HEAD PLATE CABLE from the WEIGHT STACK SHAFT & the D-RING and remove HEAD PLATE CABLE. The HEAD PLATE CABLE will be used later. See FIGURE 3. (NOTE: Remove pulleys for ease of removal.)
- Page 6 STEP 4 • Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS and ELASTIC CORD. (NOTE: The LAT or LEG EXT CABLE can be moved over one hole on the D-RING so the KEYHOLE CLEVIS are evenly spaced .) • Discard the KEYHOLE CLEVIS and ELASTIC CORD. FIGURE 5 3/8”...
- Page 7 FIGURE 6 3/8 X 1” 11 STEP 6 • (NOTE: STEP 6 is only completed if the 100101 LEG PRESS OPTION is installed otherwise proceed to STEP 7.) • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOLT (11), one previously removed 3/8”...
- Page 8 3/8 X 1/2” SPACER STEP 8 • Remove two 2” PULLEYS to the rear bracket on the TOP BOOM using one 3/8” THREADED SHAFT, two 3/8” WASHERS, two 3/8” HEX NUTS, and two 3/8” LOCK NUTS as shown in FIGURE 8. •...
- Page 9 FIGURE 10 PRESS CABLE (67249) STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10.
- Page 10 FIGURE 11 PRESS-STACK CABLE (7032302) STEP 11 • Route the new PRESS-STACK CABLE (5) around the pulleys and l-brackets as shown in STEP 11. (Remove pulleys for ease of installation.) PRESS- STACK CABLE (7032302) FIGURE 12 STEP 12 • To assemble the PRESS-STACK CABLE (5) follow the cable routing as shown and use the following steps: •...
- Page 11 STEP 13 • Snap two WEIGHT PLATE BUSHINGS (17) each, into the “ top” side of fifteen WEIGHT PLATES (16) as shown in FIGURE 13. • Slide the WEIGHT PLATE SHAFT (2) thru the hole in the HEAD PLATE(4), and lock in place using one 3/4”...
- Page 12 FIGURE 15 STEP 15 • Insert four CAP PLUGS (9) into the top and bottom ends of the GUIDE RODS (1) as shown in FIGURE 15. • Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 15. (NOTE: Lubricate GUIDE RODS (1) with silicon or teflon spray available at most hardware stores.) •...
- Page 13 FIGURE 16 STEP 16 • CAREFULLY lift or tilt the TOP BOOM and insert all GUIDE RODS into the bushings. See FIGURE 16. • With the GUIDE RODS (1) securely held in the TOP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sure the LAT CABLE runs over the top of the bolts in the TOP BOOM.) TOP BOOM TIGHTEN! (NOTE: Make sure...
- Page 14 STEP 17 • Screw one of the threaded ends of the previously removed HEAD PLATE CABLE approximately 1” into the end of the WEIGHT STACK SHAFT. See FIGURE 17. STEP 18 • Route the thread end of HEAD PLATE CABLE up and over the PULLEYS in the TOP BOOM above the WEIGHT STACK.
- Page 15 REAR SHROUD FIGURE 19 STEP 19 • The rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the plastic SHROUD as shown in FIGURE 19.
- Page 16 • SECURELY attach the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS from the bottom of the front SHROUD & rear SHROUD. Remove the SHROUDS from the 425103 HOME GYM. See FIGURE 21. • The PRESS STATION and SWIVEL LOW PULLEY are now operated with the front stack and the LAT, PEC, and LEG STATION are now operated with the rear stack.
- Page 17 YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION. REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND MAIL BACK. MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ Thank you for purchasing the ParaBody 663 600 Second Stack Option. MAINTENANCE...
-
Page 18: Limited Warranty
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. - Page 19 14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A. Tel: 763.323.4500 Fax: 763.323.4797 800.328.9714 (Toll-free within the U.S. and Canada) INTERNATIONAL OFFICES LifeFitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 LifeFitness EUROPE GmbH Siemensstrasse 3 85716 Unterschleissheim...