Parabody home gym assembly instructions (27 pages)
Summary of Contents for ParaBody GS4
Page 1
LEG PRESS ADAPTER KIT FOR GS4 GYM SYSTEM WARNING: Read and follow all directions for each step to insure proper assembly of this product. USER’S GUIDE CLASS H PART # 7362701 REV. A Version: GS4-LP5A-101 Revision: 11/01/02...
Please note: * Thank you for purchasing the ParaBody GS4 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
DESCRIPTION PART # CONNECTING TUBE ACU04-1525 ACU04-1526 PULLEY HOUSING CABLE RETAINER ACU02-0055 LEG PRESS CABLE 202-3/4 ACU13-0149 ACU06-0024 3-1/2 PULLEY 3/8” X 5-3/4” BOLT ACUDA1E03853416NB 3/8 X 4-3/4” BOLT ACUDA1E03843416NB 3/8” X 3-3/4” BOLT ACUDA1E03833416NB NOTE: The LEG PRESS ATTACHMENT (LP5) must be assembled before connecting it to the PARABODY GS1/GS2 GYM SYSTEMS FIGURE 1 STEP 1:...
Page 5
3/8 X 5-3/4” FIGURE 2 STEP 2: • Install PULLEY HOUSING (2) using two 3/8 X 5-3/4” BOLTS (6), four 3/8” WASHERS (11) and two 3/8” LOCK NUTS (12) as shown in FIGURE 2...
Page 6
3/8 X 3-3/4” FIGURE 3 STEP 3: • Assemble the new LEG PRESS to the CONNECTING TUBE (1) using two 3/8 X 3-3/4” BOLTS (8), four 3/8” WASHERS (11) and two 3/8” LOCK NUTS (12) as shown in FIGURE 3...
Page 7
FIGURE 4 STEP 4: • Screw the threaded end of the LEG PRESS CABLE (4) into the end of the FLOATING PULLEY BRACKET. Secure the CABLGUIDE in place with the JAM NUT on the GUIDE CABLE. See FIGURE 4(a) • Route the LEG PRESS CABLE (3) around one 3-1/2” PULLEY (5) and re-assemble the PULLEY to the FLOATING PULLEY PLATES usingthe BOLT, NUT and PULLEY which were removed.
Page 8
FIGURE 5 STEP 5: • Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the BRACKET (from 100 LEG PRESS kit) using one 3/8 X 1-3/4” BOLT (10), one 3/8” WASHER (11), one “L” CABLE RETAINER (3) and one 3/8”...
Page 9
FIGURE 7 3/8 LOCK NUT STEP 7: • Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (7), two STEP SPACERS 1-9/16” (14) and one 3/8” LOCK NUT (12) as shown in FIGURE 7. Make sure the CABLE is in the grooves of all the pulleys.
Page 10
FIGURE 9 3/8” LOCK NUT STEP 9: • Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (7), two STEP SPACERS 1-9/16” (14), and one 3/8” LOCK NUT (12) as shown in FIGURE 9.
FIGURE 12 SEAT FRAME 3/8 X 4-3/4” 7 STEP 12: • SECURELY assemble the swivel end of the LEG PRESS CABLE (4) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (15), two STEP SPACERS 1-11/16” (15) and one 3/8” LOCK NUT (12). (NOTE: SECURELY tighten, then back nut off 1/4 turn) CABLE ROUTING DIAGRAM...
Page 12
THIS CONCLUDES THE ASSEMBLY OF THE GS4-LP5A LEG PRESS ADAPTER KIT Thank you for purchasing the Parabody GS4-LP5A Leg Press Adapter Kit. If unsure of proper use of equip- ment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.