Parabody home gym assembly instructions (18 pages)
Summary of Contents for ParaBody GS2
Page 1
LEG PRESS ADAPTER KIT FOR GS1/GS2 GYM SYSTEM WARNING: Read and follow all directions for each step to insure proper assembly of this product. USER’S GUIDE CLASS H PART # 7358101 REV. A Version: GS1-LP5A-101 Revision: 11/01/02...
Please note: * Thank you for purchasing the ParaBody GS1/ GS2 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
ACU06-0362 ACUDC1250100020B ACUDB2E03811000B 3/8 X 1-3/4” BOLT ACUDA1E03813416NB NOTE: The LEG PRESS ATTACHMENT (LP5) must be assembled before connecting it to the PARABODY GS1/GS2 GYM SYSTEMS FIGURE 1 STEP 1: • Remove the bolts attaching the FRAME BRACE and CABLE to the BASE as shown in figure 1 •...
Page 5
• If not already installed, slide one 2” COVER CAP (4) over the FRONT LEG (1) as shown in FIGURE 8 • SECURELY assemble the FRONT LEG (1) to the GS1/GS2 Gym System using two 3/8 X 4” BOLTS (9), four 3/8” WASHERS (5), two LOW HEIGHT 3/8” LOCK NUTS (6) as shown in FIGURE 2.
Page 6
FIGURE 3 STEP 3: • Assemble the new LEG PRESS CABLE (2) using the previously removed bolts as shown in FIGURE 3. (NOTE: Make sure the LEG PRESS CABLE is running in the grooves of all pulleys and above the retaining bolts.)
Page 7
FIGURE 4 STEP 4: • SECURELY assemble one 3-1/2” PULLEY (3) to the FRONT LEG (1) using one 3/8 X 1-3/4” BOLT (7) and one 3/8” LOCK NUT (6). See FIGURE 4. 7 3/8 X 1-3/4”...
Page 8
FIGURE 5 STEP 5: • SECURELY attach the LP5 LEG PRESS to the FRONT LEG (1) using two 3/8” X 2-3/4” BOLTS (8), two 3/8” WASHERS (5), and two 3/8” LOCK NUTS (6). See FIGURE 5. FIGURE 6 STEP 6: •...
Page 9
3/8 LOCK NUT STEP 7: • SECURELY attach the BRACKET (from LP5 LEG PRESS) to the SEAT FRAME using two 3/8” X 4-3/4” BOLTS (10), two 3/8” WASHERS (5), and two 3/8” LOCK NUTS (6). See FIGURE 7. FIGURE 8 STEP 8: •...
Page 10
FIGURE 9 3/8 LOCK NUT STEP 9: • Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (3) and SECURELY assemble the 3-1/2” PULLEY (3) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (10), two STEP SPACERS 1-19/32” (12) and one 3/8” LOCK NUT (6) as shown in FIGURE 9.
Page 11
FIGURE 11 3/8” LOCK NUT STEP 11: • Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (3) and SECURELY assemble the 3-1/2” PULLEY (3) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (10), two STEP SPACERS 1-19/32” (12), and one 3/8” LOCK NUT (6) as shown in FIGURE 11.
FIGURE 13 SEAT FRAME 3/8 LOCK NUT 3/8 X 4-3/4” 10 STEP 13: • SECURELY assemble the swivel end of the LEG PRESS CABLE (2) to the SEAT FRAME using one 3/8 X 4-3/4” BOLT (10), two STEP SPACERS 1-11/16” (13) and one 3/8” LOCK NUT (6). (NOTE: SECURELY tighten, then back nut off 1/4 turn) CABLE ROUTING DIAGRAM...
Page 13
ADJUST! FIGURE 14 STEP 14: • Before setting the correct amount of tension in the cables, push the HEAD PLATE down, insert the WEIGHT SELECTOR PIN, and perform several repetitions at the leg press station. This will relax the cable system and prevent the HEAD PLATE from lifting up.