Miele TX2070 Operating Instructions Manual
Hide thumbs
Also See for TX2070:
- Operating instructions manual (112 pages) ,
- Operating and installation instructions (56 pages) ,
- Operating and installation instructions (44 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Miele TX2070
Summary of Contents for Miele TX2070
-
Page 1: Operating Instructions
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is in‐ stalled and used for the first time. en-AU, NZ HG06 M.-Nr. -
Page 3: Table Of Contents
Contents Guide to the appliance................... 6 Appliance overview....................6 Control panel......................7 Warning and Safety instructions ................8 Caring for the environment ................. 17 Disposal of the packing material................17 Disposing of your old appliance ................17 Energy-saving dishwashing ................... 18 Before using for the first time................ - Page 4 Contents Starting the programme ..................45 Display ........................45 Energy management ....................46 Programme finished ....................46 Switching off ......................47 Unloading the dishwasher ..................47 Interrupting a programme ..................48 Changing a programme ..................48 Programme options ..................... 49 Short ...
- Page 5 Contents Electrical connection ................... 79 Water connection....................80 The Miele Waterproof system ................80 Connection to the water supply................80 Drainage......................... 81 Technical data ...................... 82...
-
Page 6: Guide To The Appliance
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Rinse aid reservoir d Middle spray arm j Dual compartment detergent dis‐ penser e Air inlet for drying (depending on model) -
Page 7: Control Panel
Guide to the appliance Control panel a Programme selection e Short button with indicator light b Display f Delay start button with indicator light c Check/Refill indicators g Programme selector button d Start button with indicator light h On/Off button ... -
Page 8: Warning And Safety Instructions
Keep the installation plan and the operating instructions in a safe place and pass them on to any future owner. Miele cannot be held liable for damage caused by non-compli‐ ance with this information. - Page 9 Warning and Safety instructions Correct application This appliance is designed for domestic use and for use in similar environments by guests in hotel or motel rooms, bed & breakfasts and other typical living quarters. This does not include common/ shared facilities or commercial facilities within hotels, motels or bed &...
- Page 10 Warning and Safety instructions Safety with children Young children must not be allowed to use this appliance. Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely, rec‐ ognising the dangers of misuse.
- Page 11 Repairs and other work by unqualified persons could be danger‐ ous. Installation, maintenance work and repairs to electrical applian‐ ces must only be carried out by a Miele approved service technician. Before installation, check the dishwasher for visible signs of dam‐...
- Page 12 The water pressure (flow pressure at the connection point) must be between 30 and 1000 kPa (0.3 and 10 bar). A damaged appliance could be dangerous. If the dishwasher gets damaged, switch it off at the mains and call Miele.
- Page 13 If the connection cable is damaged, it must be replaced with a special cable of the same type (available from Miele) by a Miele au‐ thorised service technician only. In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times.
- Page 14 Warning and Safety instructions If you want to convert your freestanding dishwasher to a built-un‐ der ("U") model, you will need to order the appropriate conversion kit. If you remove the existing plinth, you must replace it with a U- model plinth.
-
Page 15: Correct Use
Warning and Safety instructions Correct use Do not use solvents in the dishwasher. Danger of explosion! Do not inhale or ingest dishwasher detergent. Dishwasher deter‐ gents contain irritants or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breath‐ ing. - Page 16 Accessories Use only genuine original Miele spare parts. If spare parts or ac‐ cessories from other manufacturers are used, the warranty will be in‐ validated, and Miele cannot accept liability. Disposal of your old dishwasher ...
-
Page 17: Caring For The Environment
Caring for the environment Disposal of the packing mate‐ Disposing of your old appli‐ rial ance The packaging is designed to protect Electrical and electronic appliances of‐ the appliance from damage during ten contain materials which, if handled transportation. The packaging materials or disposed of incorrectly, could be po‐... -
Page 18: Energy-Saving Dishwashing
If the water is heated by solar panels, for example, this would be energy efficient. However, if your water is heated by electricity, we would recommend connection to cold water. You can find further tips on energy- saving dishwashing in "Miele's guide to dishwashing". -
Page 19: Before Using For The First Time
Before using for the first time Opening the door Closing the door Push the baskets right in. Then lift the door upwards and push until it clicks into position. Danger of injury! Do not put your hand inside the door as it is closing. -
Page 20: Water Softener
Before using for the first time Water softener Enter the water hardness below: ____________mmol/l or °d In order to achieve good cleaning re‐ sults, the dishwasher needs to operate The dishwasher is programmed at the with soft water. Hard water results in a factory for a water hardness level of 2.7 build-up of calcium deposits on crock‐... -
Page 21: Displaying And Setting The Water Hardness Level
Before using for the first time Displaying and setting the water The value which has been set for the hardness level water hardness is shown as a figure af‐ ter in the display (see chart). Switch the dishwasher off with the button if it is switched on. - Page 22 Before using for the first time °d mmol/l °f Display °d mmol/l °f Display 37-45 6.6-8.0 66-80 46-60 8.2-10.7 82-107 61-70 10.9-12.5 109-125...
-
Page 23: Before Using The Appliance For The First Time, You Require
Before using for the first time Before using the appliance for If the water hardness in your area is the first time, you require: constantly lower than 0.9 mmol/l (5 °d), you do not need to add dish‐ – approx. 1 litre of water, washer salt. -
Page 24: Filling The Salt Reservoir
Before using for the first time Filling the salt reservoir Before filling the salt reservoir with dishwasher salt for the first time, you must fill it with approx. 1 litre of wa‐ ter to enable the salt to dissolve. Once the dishwasher has been used, there is always sufficient water in the reservoir. -
Page 25: Salt Indicator
Before using for the first time Salt indicator If you only ever use multi-function combination products in your dish‐ Fill the salt reservoir with dishwasher washer, you can switch off both refill salt when the Salt indicator light reminders for salt and rinse aid if you comes on (If it comes on during a wish (see "Programme options - programme, wait until the end of the... -
Page 26: Rinse Aid
Before using for the first time Rinse aid If you only ever use combination products containing rinse aid in your Rinse aid is necessary to ensure water dishwasher, you do not need to add does not cling and leave marks on rinse aid. -
Page 27: Rinse Aid Indicator
Before using for the first time Rinse aid indicator When the Rinse aid indicator light comes on, the reservoir contains suffi‐ cient rinse aid for 2 - 3 programmes on‐ Add rinse aid in plenty of time. If you only ever use multi-function combination products in your dish‐... -
Page 28: Setting The Rinse Aid Dosage
Before using for the first time Setting the rinse aid dosage Switch the dishwasher off with the button if it is switched on. You can adjust the rinse aid dosage for best results. Press the Start button in and, whilst holding it in, switch the dishwasher The rinse aid dosage can be set from on using the ... -
Page 29: Loading The Dishwasher
Loading the dishwasher Notes – The spray arms must not be blocked by items which are too tall or hang Remove coarse food residues from through the baskets. If in doubt, test crockery. for free movement by manually rotat‐ ing the spray arms. There is no need to rinse items under running water. - Page 30 – Use detergents with glass protective ted at the end of a programme, where additives (e.g. Miele CareCollection water has not run off smoothly. It may tabs). need to be rubbed dry with a soft cloth.
-
Page 31: Upper Basket
Loading the dishwasher Upper basket Cup rack See "Loading the dishwasher - Load‐ ing examples" for examples of how to load crockery and cutlery. For safety reasons, do not oper‐ ate the dishwasher without the upper and lower baskets in place. ... -
Page 32: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or up‐ per basket, the upper basket can be Dishwashers with cutlery tray adjusted on three levels with 2 cm be‐... -
Page 33: Lower Basket
Loading the dishwasher Lower basket Hinged spikes Both rows of spikes at the front can be See "Loading the dishwasher - Load‐ lowered to make more room for large ing examples" for examples of how to items, e.g. pots, pans and dishes. load crockery and cutlery. - Page 34 Loading the dishwasher Removable spiked insert Bottle holder (depending on model) For plates, bowls, pans, etc. The bottle holder can be used to wash narrow items, e.g. milk and baby bot‐ The spiked insert at the back can be re‐ tles.
-
Page 35: Cutlery
Loading the dishwasher Cutlery Cutlery tray See "Loading the dishwasher - Load‐ ing examples" for examples of how to load crockery and cutlery. Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 36: Loading Examples
Loading the dishwasher Loading examples Dishwashers with cutlery tray Upper basket Lower basket... - Page 37 Loading the dishwasher Cutlery tray Heavily soiled items...
-
Page 38: Comparison Tests
Comparison tests Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for energy label comparison tests: Capacity: 10 place settings Detergent quantity: 27.5 g in Compartment II Rinse aid dispensing: Setting 3 You can find information on adjusting the rinse aid dosage in the "Rinse aid" section of this booklet. -
Page 39: Capacity
Comparison tests Capacity 10 ... - Page 40 Comparison tests ...
-
Page 41: Operation
For optimum cleaning and drying re‐ remove coloured stains (e.g. tea, cof‐ sults, use Miele dishwasher detergent fee, tomato sauce). and add Miele salt and Miele rinse aid separately. See "Optional accesso‐ Most dishwasher detergents are mildly ries". alkaline and contain enzymes and oxy‐... - Page 42 Operation Detergent dosage Dishwasher detergents contain Follow the dosage recommended by irritant or corrosive ingredients which the manufacturer on the packaging. can cause burning in the nose, mouth and throat if swallowed, or in‐ Unless directed otherwise, use one hibit breathing.
-
Page 43: Adding Detergent
Operation Adding detergent Add the required amount of detergent and close the flap. Press the opening catch on the de‐ tergent dispenser. The flap will spring Make sure that the detergent packag‐ open. ing is properly closed after use to avoid it getting damp and becoming The flap is always open at the end of a lumpy. -
Page 44: Switching On
Operation Switching on Selecting a programme Make sure the spray arms are not ob‐ Choose your programme according to structed. the type of load and how dirty it is. Close the door. The different programmes and their uses are described in the Programme ... -
Page 45: Starting The Programme
Operation Starting the programme Display Press the Start button. The duration of the programme selec‐ ted appears in hours and minutes in the The programme will begin. display before the programme begins. The Start indicator light will come on. During the programme the time left until the end of the programme is displayed. -
Page 46: Energy Management
Operation Energy management Programme finished To save energy, the dishwasher will The programme has ended when . switch off automatically 10 minutes af‐ appears in the display. ter the last time a button has been The drying fan may continue to run for pressed or 10 minutes after the end of a few minutes at the end of the pro‐... -
Page 47: Switching Off
Operation Switching off Unloading the dishwasher At the end of a programme: Dishes tend to break and chip more easily when they are hot. Allow the The dishwasher can be switched off dishes to cool until they are comforta‐ at any time using the ... -
Page 48: Interrupting A Programme
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as If the detergent dispenser flap has the door is opened. already opened, do not change the If the door is closed again, the pro‐ programme. gramme will continue from the point it was at before the door was opened. -
Page 49: Programme Options
Programme options Short DetergentAgent For optimum cleaning results, the dish‐ The Short option reduces the dura‐ washer automatically adjusts the pro‐ tion of programmes in which this option gramme sequence to the type of deter‐ is available. gent being used. Depending on the In order to achieve optimum cleaning programme, this can mean that the run‐... -
Page 50: Switching Off The Refill Indicators
Programme options Switching off the refill indica‐ Press the button 9 times. tors The indicator light will flash rapidly 9 times at intervals. If you only ever use multi-function com‐ bination products in your dishwasher, The flashing sequence in the display you can switch the refill reminders for will appear whether the refill indicators salt and rinse aid off if you wish. -
Page 51: Delay Start
Programme options Delay start Switch the dishwasher on with the button. The start time of a programme can be The Start indicator light will flash. delayed, e.g. to take advantage of night time electricity tariffs. The start time ... - Page 52 Programme options Starting a programme before the De‐ If optimise standby is switched on lay start period has elapsed: (see "Programme options - Optimise standby"), the display will go out after A programme can be started before the a few minutes, leaving just the Start Delay start period has elapsed.
-
Page 53: Adjust Sensor Wash
Programme options Adjust Sensor wash Press the button 5 times. You can adjust the Sensor wash pro‐ The indicator light will flash rapidly 5 gramme so that it will remove stubborn times at intervals. soiling in a lightly soiled load. The flashing sequence in the display in‐... -
Page 54: Optimise Standby
Programme options Optimise standby Press the button 8 times. "Optimise standby" is activated by de‐ The indicator light will flash rapidly 8 fault. times at intervals. To save energy, the dishwasher will The flashing sequence in the display switch off automatically a few minutes shows whether "Optimise standby"... -
Page 55: Factory Default Settings
Programme options Factory default settings Press the button 19 times. If you have altered any settings from The indicator light will do 1 long the factory default, you can reset them flash and 9 short flashes at intervals. back to the factory default settings as The flashing sequence in the display in‐... -
Page 56: Programme Chart
Programme chart Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying °C °C Sensor wash Variable programme sequence, sensor-controlled adjustment according to amount of crockery and soiling 47-55 required required Light soiling 55°C Intensive 75°C Sensor wash gentle Quick wash 40°C This programme is the most efficient in terms of its combined energy and water con‐... - Page 57 Programme chart Consumption Duration Electricity Water Cold water Hot water Litres Cold water Hot water h:min h:min 0.60 0.35 2:37 2:33 1:25-2:40 1:20-2:30 0.70 -1.15 0.55 -0.75 -14.0 1.15 0.65 13.0 1:59 1:47 1.30 0.90 14.0 2:54 2:42 0.85 0.50 11.5 1:41 1:32...
- Page 58 Programme chart Crockery Food deposits Action required Variable, sensor-controlled Mixed, All fresh to dried-on programme sequence everyday crockery food deposits Shorter duration This needs a short programme Heat-sensitive glasses and plastic Shorter duration Fresh, easily removed food deposits This needs a gentle programme with glass care Shorter duration Mixed crockery...
- Page 59 Programme chart Programme Detergent Compartment I Compartment II 25 ml Sensor wash 1 tab +short 20 ml Quick wash 40 °C 1 tab +short 20 ml Sensor wash gentle 1 tab +short 25 ml 1 tab 25 ml Light soiling 55 °C 1 tab +short 25 ml...
-
Page 60: Cleaning And Care
If, however, there are limescale or grease deposits in the cabinet, these can be removed with the Original Miele dishwasher conditioning agent (availa‐ ble from Miele or at www.miele- shop.com, depending on country). Fol‐... -
Page 61: Cleaning The Door Front
– dishwasher cleaner, For cleaning, you can also use a clean, damp microfibre cloth, such as – oven cleaner, the Original Miele all purpose microfi‐ – glass cleaning agents, bre cloth, without any cleaning agent. – hard, abrasive brushes or sponges, e.g. -
Page 62: Checking The Filters In The Wash Cabinet
Cleaning and care Checking the filters in the Cleaning the filters wash cabinet Switch the dishwasher off. The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it access‐ ing the circulation system and re-enter‐ ing the cabinet through the spray arms. - Page 63 Cleaning and care To clean the inside of the filter, the flap Replace the filter combination so that must be opened: it lies flat in the base of the wash cabinet. Press the catches together in the direction of the arrows as shown, and ...
-
Page 64: Cleaning The Spray Arms
Cleaning and care Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). Switch the dishwasher off. Remove the spray arms as follows: ... -
Page 65: Problem Solving Guide
Reset or replace the fuse (see data plate for mini‐ button. mum fuse rating). The dishwasher stops The mains fuse has tripped. during a programme. Reset or replace the fuse (see data plate for mini‐ mum fuse rating). If the mains fuse trips again, call Miele. - Page 66 Press the Start button. If the indicator lights flash again, there is a technical fault. Call Miele. Fault : The Waterproof system has reacted. The drain pump is still Turn off the tap.
-
Page 67: Water Inlet Fault
Problem solving guide Water inlet fault Problem Possible cause and remedy The Inlet/Drain indica‐ The tap is turned off. tor light flashes. Turn on the tap fully. The dishwasher stops Before rectifying the problem you must: during a programme. ... -
Page 68: Water Drainage Fault
Problem solving guide Water drainage fault Problem Possible cause and remedy The dishwasher stops Before rectifying the problem you must: during a programme. Switch the dishwasher off with the button. The Inlet/Drain indica‐ The water outlet is restricted. tor light flashes. -
Page 69: General Problems
Problem solving guide General problems Problem Possible cause and remedy The indicator lights and The dishwasher has switched off automatically to display are dark. save energy. Switch the dishwasher on again with the but‐ ton. Detergent residue is left The dispenser was still damp when detergent was in the dispenser at the added. -
Page 70: Noises
Problem solving guide Noises Problem Possible cause and remedy Knocking noise in the A spray arm is knocking against an item in a basket. wash cabinet. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the Items of crockery are insecure in the wash cabinet. -
Page 71: Unsatisfactory Washing Result
Problem solving guide Unsatisfactory washing result Problem Possible cause and remedy The dishes are not The dishes were not loaded correctly. clean. See notes in "Loading the dishwasher". The programme was not powerful enough. Select a more intensive programme (see "Pro‐ gramme chart"). - Page 72 Problem solving guide Problem Possible cause and remedy Dishes, cutlery and The amount of rinse aid may be insufficient, or the glasses are not dry or rinse aid reservoir is empty. are flecked. Replenish the reservoir, increase the dosage or change the brand of rinse aid (see "Before using for the first time - Rinse aid").
- Page 73 Problem solving guide Problem Possible cause and remedy White residue is visible Not enough rinse aid was used. on cutlery and crock‐ Increase the dosage (see "Before using for the first ery, clouding occurs on time - Rinse aid"). glassware;...
-
Page 74: Maintenance
This Replace the filter and washer, making filter is available from Miele. sure they are sitting correctly. Reconnect the inlet hose to the tap, Cleaning the filter: making sure it goes on correctly and ... -
Page 75: Cleaning The Drain Pump And Non-Return Valve
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme, the drain pump or the non-return valve might be blocked. They are, however, easy to clean. Disconnect the dishwasher from the mains supply. -
Page 76: After Sales Service
For further information, please refer to – Miele your warranty booklet. The contact details for Miele are giv‐ en at the back of these instructions. When contacting Miele, please quote the model and serial number of your dishwasher, both of which are shown on the data plate on the right-hand side of the door. -
Page 77: Optional Accessories
– phosphate-free - safe for the environ‐ www.miele-shop.com (depending on ment country) or from Miele (see end of this booklet for contact details). – water-soluble wrapping - no need to unwrap Powder detergent –... - Page 78 Optional accessories Dishwasher care products Insert for glasses The insert for glasses fits in the lower Miele cleaning and care products pro‐ basket and is designed to accommo‐ vide optimum care for your dishwasher. date lots of glasses. Dishwasher cleaner –...
-
Page 79: Electrical Connection
(e.g. danger of overheating). safety regulations. If the connection cable is damaged, it must be replaced with a Miele cable of the same type by a Miele approved service technician only. Do not connect the appliance to an in‐... -
Page 80: Water Connection
As long as your dishwasher has been 30 and 1000 kPa (0.3 and 10 bar). If installed correctly, the Miele waterproof the water pressure is too high, a anti-leak system will protect you from pressure reducer valve must be fit‐... -
Page 81: Drainage
Water connection Drainage Venting the drainage system If the on-site drain connection is situ‐ – The appliance drainage system is fit‐ ated lower than the guide path for the ted with a non-return valve which bottom basket rollers in the open door, prevents dirty water from flowing the drainage system must be vented. -
Page 82: Technical Data
Technical data Height freestanding model 84.5 cm (adjustable + 3.5 cm) Height built-in model 80.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Width 44.8 cm Width of building-in recess 45 cm Depth freestanding model 60 cm Depth built-in model 57 cm... - Page 84 G 4700 en-AU, NZ M.-Nr. 09 867 810 / 01...