Accessories - Lincoln Electric SP-170T Operator's Manual

C-1
OPTIONAL ACCESSORIES
1. K549-1 .035" (0.9 mm) Innershield® Welding Kit
— Includes a contact tip, a gasless nozzle and a
.035/.045" (.9/1.2 mm) cable liner to permit the
Magnum™ 100L gun and cable to use .035" (0.9
mm) diameter flux-cored electrode. The fitting on
the end of the liner is stenciled with the maximum
rated wire size (.045"/1.2 mm). Also included is a
10 lb.(4.5 kg.) spool of .035" (0.9 mm) Innershield
NR-211-MP.
See "Innershield (FCAW) Conversion" in this sec-
tion for installation instructions and MAINTE-
NANCE section for proper feeding component con-
figuration and installation.
2. K549-2 .045" (1.2 mm) Innershield® Welding Kit
— Includes a contact tip, a gasless nozzle and a
.035/.045" (0.9/1.2 mm) cable liner to permit the
Magnum™ 100L gun and cable to use .045" (1.2
mm) diameter flux-cored electrode. The fitting on
the end of the liner is stenciled with the maximum
rated wire size (.045"/1.2 mm). Also included is a
10 lb.(4.5 kg.) spool of .045" (1.2 mm) Innershield
NR-211-MP and a knurled drive roll.
See "Innershield (FCAW) Conversion" in this sec-
tion for installation instructions and MAINTE-
NANCE section for proper feeding component con-
figuration and installation.
3. K664-2 Aluminum Feeding Kit — This kit required
for welding with .035 Aluminum wire. Included with
this kit are a drive roll, cable liner and .035 contact
tip. It is important when changing between
welding with steel wire and aluminum to
exchange feeding components due to the lubri-
cant applied to steel wire. Failure to do so may
result in contaminated welds when welding alu-
minum.
See Maintenance section for instructions on
installing drive roll, cable liner, contact tip and their
proper configuration.
4. KP665-045C Drive Roll – Optional — Knurled
drive roll for feeding .035 - .045" (0.9 - 1.2 mm)
diameter flux-cored electrode.

ACCESSORIES

5. K695-1 Spot / Stitch Timer Kit — Includes spot
timer to control the spot welding arc time, and a
stitch timer to control the on/off cycle time of the
arc to prevent burnthrough on thin gauge metals.
Also includes spot welding nozzle.
The Spot/Stitch Timer Kit installs inside the wire
feed compartment, replacing the blank panel locat-
ed below the gun trigger lead connectors, per the
installation instructions (M17920) included with the
® kit.
6. K520 Utility Cart — Designed to transport the
Lincoln family of small welders. Has provisions for
mounting a single gas cylinder. Has front casters
and large rear wheels. Handle height is easily
adjustable. Bottom tray provided for tools and
accessories. Easy assembly required; takes less
than 15 minutes.
7. K1800-1 CO
Includes an adjustable pressure and flow regulator
for use on CO
hose which connects to the rear of the welder.
®
See "Gas Connection" in Installation section for
installation instructions.
8. K1799-1 Argon-Mixed Ajustable Gas Regulator
and Hose Kit
and flow regulator for use on argon-mixed gas
cylinders. Also included is a gas hose which con-
nects to the rear of the welder.
9. K586-1 Deluxe Adjustable Gas Regulator &
Hose Kit
Accommodates CO
10. K697-2 Power Cord Extension — Extension
230V power cord (20'/6.1m) allows extra conve-
nience when work is located some distance away
from power receptacle.
11. K667-1 230 Volt 50 Amp Receptacle — For pro-
viding power for your SP-170T at your welding
location. NEMA standard 6-50 R receptacle. See
"Line Cord Connection" in INSTALLATION section
for recommended wire size.
(1) This regulator comes standard with a 4.5 foot hose
with the SP-17OT.
SP-170T
Gas Regulator & Hose Kit —
2
cylinders. Also included is a gas
2
(1)
— Includes an adjustable pressure
or mixed Gas Cylinders.
2
C-1